Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Crown race replacement

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Crown race replacement

Old 12-04-22, 09:09 AM
  #1  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Crown race replacement

Hiya folks,
I'm about to replace my headset and there's one item I'm not sure about: 'hammering' the crown race into place.

I've read Sheldon Brown and he says put a pipe over the steerer and tap on it.
Other people say put a pipe (PVC, mild steel etc) over the steerer and bang the pipe against the ground.

My question is: why don't people just use a short length of pipe (about 6") and tighted down the locknut against it ?
Aardwolf is offline  
Old 12-04-22, 09:50 AM
  #2  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,003

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4172 Post(s)
Liked 3,792 Times in 2,271 Posts
The pipe to be pressed down by the lock nut will need to be a fairly exact length. So one would need to make the pipe anew for every bike they do this job on. The amount of force to press the crown race on can be more than what the steerer/lock nut threads are made to handle. Shock does a better job at this job than mere pressure will do and can be faster to attain. What will one do if the fork is threadless? Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 12-04-22, 10:35 AM
  #3  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Originally Posted by Andrew R Stewart
The amount of force to press the crown race on can be more than what the steerer/lock nut threads are made to handle.
Cheers.
That's the bit I was concerned about, probably better to follow what Sheldon said then

As far as I can remember there's about 3" of thread on my forks.
And I agree it doesn't apply to threadless forks, but I don't have any such modern devices.
Aardwolf is offline  
Old 12-04-22, 10:42 AM
  #4  
dedhed
SE Wis
 
dedhed's Avatar
 
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,516

Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970

Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2731 Post(s)
Liked 3,361 Times in 2,034 Posts
Verify your crown race and seat are both the same i.e. ISO and JIS diameters are different.
dedhed is offline  
Likes For dedhed:
Old 12-04-22, 11:03 AM
  #5  
FBinNY 
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,544

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,432 Times in 1,345 Posts
It's mainly a question of good use of time.

Instead of crapping around with more tools, ie. a wrench for the lockout, and trying to tighten it while holding the fork, you can simply use the pipe you need anyway as a slide hammer and be done.

Plus the slide hammer method offers positive confirmation that the crown is seated via a change in the sound.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is online now  
Likes For FBinNY:
Old 12-04-22, 11:05 AM
  #6  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,003

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4172 Post(s)
Liked 3,792 Times in 2,271 Posts
With about 3" of threading on your fork I am concerned about the stem's wedge sitting within that threaded portion. That would be bad and most fork makers won't warranty the fork after the stem expands and cracks the steerer. The threaded portion is vastly more prone to this than the rest of the steerer. As this portion of the steerer is out of sight and since the result of steering loss is so bad I strongly suggest that you make sure the stem wedge is below that threaded section. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 12-04-22, 01:00 PM
  #7  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Originally Posted by Andrew R Stewart
With about 3" of threading on your fork I am concerned about the stem's wedge sitting within that threaded portion.
Just checked and it's 45mm of thread and the wedge is just below that.
Also remembered that I checked the wedge position about a year back to make sure it was clear of the thread
Must be getting old or something.
Aardwolf is offline  
Likes For Aardwolf:
Old 12-04-22, 03:19 PM
  #8  
gearbasher
Senior Member
 
gearbasher's Avatar
 
Join Date: May 2009
Location: Sitting on my butt in front of a computer
Posts: 1,535
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 439 Post(s)
Liked 835 Times in 363 Posts
Originally Posted by FBinNY
It's mainly a question of good use of time.

Instead of crapping around with more tools, ie. a wrench for the lockout, and trying to tighten it while holding the fork, you can simply use the pipe you need anyway as a slide hammer and be done.

Plus the slide hammer method offers positive confirmation that the crown is seated via a change in the sound.
This is the method I've always used without fail. Just tap it on by sliding the pipe up and down. It doesn't take much force.
gearbasher is offline  
Old 12-05-22, 05:52 AM
  #9  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Originally Posted by dedhed
Verify your crown race and seat are both the same i.e. ISO and JIS diameters are different.
I had read about that and was fairly certain mine was ISO - it's a 1982 Holdsworth with an original Tange headset.

Fork measures 26.98
The removed crown race measures 26.8
The replacement (Tange Levin CDS) is 26.3

Rats, I'm guessing I need a JIS one.
Seems like this was known if I'd only looked: https://forum.cyclinguk.org/viewtopic.php?t=17078

Update: Tange Levin CDS also comes as JIS, but not as common.

Last edited by Aardwolf; 12-05-22 at 06:42 AM. Reason: update
Aardwolf is offline  
Old 12-05-22, 07:11 AM
  #10  
dedhed
SE Wis
 
dedhed's Avatar
 
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,516

Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970

Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2731 Post(s)
Liked 3,361 Times in 2,034 Posts
Originally Posted by Aardwolf
I had read about that and was fairly certain mine was ISO - it's a 1982 Holdsworth with an original Tange headset.

Fork measures 26.98
The removed crown race measures 26.8
The replacement (Tange Levin CDS) is 26.3

Rats, I'm guessing I need a JIS one.
Seems like this was known if I'd only looked: https://forum.cyclinguk.org/viewtopic.php?t=17078


Update: Tange Levin CDS also comes as JIS, but not as common.

​​​​​​
You can buy Levin crown races separately.

​​​​​​https://www.somafabshop.com/shop/297...7-0-3444#attr=
https://www.retro-gression.com/produ...iki-crown-race
dedhed is offline  
Likes For dedhed:
Old 12-05-22, 07:25 AM
  #11  
Schweinhund
Senior Member
 
Join Date: Oct 2022
Posts: 1,393

Bikes: a couple

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 562 Post(s)
Liked 862 Times in 455 Posts
Originally Posted by gearbasher
This is the method I've always used without fail. Just tap it on by sliding the pipe up and down. It doesn't take much force.
and if you have a problem, you clamp the pipe in the vise and invert the fork into the pipe and place a block of wood between the fork blades and hammer lightly. I've used this method on old schwinn forks more than anything else.
Schweinhund is offline  
Old 12-05-22, 08:24 AM
  #12  
Crankycrank
Senior Member
 
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,650
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 835 Post(s)
Liked 1,054 Times in 740 Posts
Also heating up the race in boiling water and if you have a large enough freezer, put the fork in there for a couple hours or put some ice around the race seat right before installing the race. Expansion/contraction trick makes it easier to get the race on.
Crankycrank is offline  
Old 12-05-22, 11:52 AM
  #13  
soyabean
Senior Member
 
soyabean's Avatar
 
Join Date: Feb 2022
Location: GMT-5
Posts: 801
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 462 Post(s)
Liked 371 Times in 246 Posts
Originally Posted by Aardwolf
Hiya folks,
I'm about to replace my headset and there's one item I'm not sure about: 'hammering' the crown race into place.
Hammering is exactly how it is done.

I use a rubber hammer.

I've found the softest ones are the cheap ones you find at places like Dollar General, but your choice to get a Park Tool HMR-4.

If the fork is too narrow, a soft piece of wood helps. Something like crappy cheap pine from pallets.

I admit there is some experience needed to constantly eyeball along every tap so it is going in evently, otherwise skewed.

I'm not sure if there can be any possible damage from an uneven seat, as I get it right all the time.
soyabean is offline  
Old 12-05-22, 12:16 PM
  #14  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Originally Posted by Schweinhund
and if you have a problem, you clamp the pipe in the vise and invert the fork into the pipe and place a block of wood between the fork blades and hammer lightly. I've used this method on old schwinn forks more than anything else.
This is an approach I like, it seems a bit more controlled.
Aardwolf is offline  
Old 12-06-22, 01:15 PM
  #15  
grumpus
Senior Member
 
grumpus's Avatar
 
Join Date: Apr 2016
Posts: 1,067
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 442 Post(s)
Liked 404 Times in 307 Posts
Originally Posted by Aardwolf
This is an approach I like, it seems a bit more controlled.
There's really no need for a hammer, piece of wood or whatever - using a steel tube as a slide hammer is quick and easy, you can hear/feel when the race is set properly, you don't risk damaging the paint because you're holding the fork in your hand and the movement of the hammer tube is constrained by the steerer. Just don't get overenthusiastic if it's a short steerer, as an unconstrained hammer tube will mess up paint quicker than you can say "oh dear" (alternatively you slam your pinky finger against the end of the steerer).
grumpus is online now  
Old 12-13-22, 09:26 AM
  #16  
Aardwolf
Wheelman
Thread Starter
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 800

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 632 Times in 320 Posts
Tange Levin JIS turned up today and I still couldn't get the crown race on.
Probably because I've only got a piece of plastic pipe - can't find a shop round here that sells the right diameter metal tube and
Amazon would take a week to deliver.

So I phoned the local LBS and walked it round there.
Harry at Elswood Cycleworks (Putney) fitted it in 15 seconds for free
He does have the right sized pipe.
Aardwolf is offline  
Likes For Aardwolf:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.