Shimano Mega 9 shifters?
#1
Senior Member
Thread Starter
Join Date: Apr 2005
Location: Ann Arbor, MI
Posts: 16,866
Bikes: 1980 Masi, 1984 Mondonico, 1984 Trek 610, 1980 Woodrup Giro, 2005 Mondonico Futura Leggera ELOS, 1967 PX10E, 1971 Peugeot UO-8
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1854 Post(s)
Liked 661 Times
in
504 Posts
Shimano Mega 9 shifters?
Mrs. Road Fan’s grocery bike, only now being pressed into service, is a 2003 Breezer Liberty, a pretty well-equipped straight bar road bike - some racks, some panniers, some 700c “urban tires, aluminum frame, Vbrakes, full fenders, Basta wheel dyno and B&M lights, and now with a B72 saddle. Hubs and derailleurs are Deore, the chainset and shifters are Shimano Mega-9.
Gearing is 3x9 roughly 22-42 in front and 12-32 in the rear. These gearing details are approximate because I haven’t counted them out for quit a while. The Mega-9 have little gear indicators, and a thumb lever to work against the springs and a finger lever to step it the other way. Front derailleur is bottom pull.
Problems: The front and rear derailleurs move properly in response to the triggers, but the shifter detects need a lot of travel before they will stick at the “new” detent. It’’s far enough that sometimes she can’t get the shift she wants without contorting her hand - unladylike!
So I think the shifters should be overhauled, if possible to clean out gummy crud that may be getting in the way of the little parts and springs.
Has anyone done this on the Mega-9’s? Any worries beyond dropping little parts into the carpet? Any instructions or rebuild kits out there?
Or do I just need new parts? The front and rear mechs are in fine shape!
Gearing is 3x9 roughly 22-42 in front and 12-32 in the rear. These gearing details are approximate because I haven’t counted them out for quit a while. The Mega-9 have little gear indicators, and a thumb lever to work against the springs and a finger lever to step it the other way. Front derailleur is bottom pull.
Problems: The front and rear derailleurs move properly in response to the triggers, but the shifter detects need a lot of travel before they will stick at the “new” detent. It’’s far enough that sometimes she can’t get the shift she wants without contorting her hand - unladylike!
So I think the shifters should be overhauled, if possible to clean out gummy crud that may be getting in the way of the little parts and springs.
Has anyone done this on the Mega-9’s? Any worries beyond dropping little parts into the carpet? Any instructions or rebuild kits out there?
Or do I just need new parts? The front and rear mechs are in fine shape!
#2
Really Old Senior Member
It sounds like the barrel adjuster needs to be turned a "few clicks" to effectively lengthen the cable housing.
#3
The Wheezing Geezer
Join Date: Oct 2021
Location: Española, NM
Posts: 1,043
Bikes: 1976 Fredo Speciale, Jamis Citizen 1, Ellis-Briggs FAVORI, Rivendell Clem Smith Jr.
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 411 Post(s)
Liked 895 Times
in
440 Posts
The left thumb on the Mega-9s I have uses a lot of travel to get its shift, and there's not much you can do about that, except maybe angle it so it's easier. The right one uses only a little travel for one shift, but can accommodate two or three positions/shifts, depending on how far you push it. Maybe stick to one-at-a-time there.
#4
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,342
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6200 Post(s)
Liked 4,201 Times
in
2,357 Posts
Agree with Bill Kapaun. Start with the cabling before anything else.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Likes For cyccommute:
#5
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,801
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1943 Post(s)
Liked 2,164 Times
in
1,323 Posts
If it is the distance of the throw and not a difficulty pushing the lever, what you have is what you have.
Cleaning might make it easier to push, but all the shifter does is pull cable. The pawl catches and everything stays there until you push it again or pull the trigger to release the pawl.
You can dink around with stops or cable adjustment all you want, but that lever will need to swing a certain amount to engage the pawl.
John
Edit added: In theory, you could reduce the lever length and the distance would be less, but the amount of thumb pressure would increase due to less leverage… literally.
Cleaning might make it easier to push, but all the shifter does is pull cable. The pawl catches and everything stays there until you push it again or pull the trigger to release the pawl.
You can dink around with stops or cable adjustment all you want, but that lever will need to swing a certain amount to engage the pawl.
John
Edit added: In theory, you could reduce the lever length and the distance would be less, but the amount of thumb pressure would increase due to less leverage… literally.
#6
Senior Member
Join Date: Feb 2012
Location: Golden, CO and Tucson, AZ
Posts: 2,835
Bikes: 2016 Fuji Tread, 1983 Trek 520
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 674 Post(s)
Liked 738 Times
in
429 Posts
Cleaning 20+ year-old shifters isn't a bad idea, but don't do it over carpet. This is one place WD-40 works well. Since they still operate, you won't need to flush them, but they'll still take a generous spray and will drip. Stand by with a rag, and put a pan on the ground/floor. Remove the cable installation access plug and squirt there. You might get a cleaner, crisper shift.
#7
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,546
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 580 Times
in
398 Posts
However, the distance the levers have to be moved to engage the pawls remains the same.