Using an undersized tube , what issues does this cause?
#1
Senior Member
Thread Starter
Using an undersized tube , what issues does this cause?
Hi there ,
Can I get away with a tube marked 35 c in a 44mm tire ?
What kind of issues if any would I have ?
Thanks
Can I get away with a tube marked 35 c in a 44mm tire ?
What kind of issues if any would I have ?
Thanks
#2
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
It'll work because butyl tubes have the ability to stretch several times their unstretched size. However, the tube is stretched much thinner so flats will be more likely. If it's all you got, pop it in and ride to the bike shop or W*lmart to get a size closer to your tire, then keep the undersized one as a spare.
Likes For ClydeClydeson:
#3
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,903
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,931 Times
in
1,212 Posts
The only time I couldn't get a glueless patch to work was in a similar situation. By the time I got the patched tube back in the tire and pumped it up to pressure, apparently the patch had almost set and then the tube stretched away from the patch as it was inflated.
Moral of the story? Always have a spare tube. And as Clyde said, get a tube that's closer to the correct size.
Moral of the story? Always have a spare tube. And as Clyde said, get a tube that's closer to the correct size.
#4
Senior Member
Join Date: Mar 2012
Posts: 982
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 506 Post(s)
Likes: 0
Liked 638 Times
in
356 Posts
It'll work because butyl tubes have the ability to stretch several times their unstretched size. However, the tube is stretched much thinner so flats will be more likely. If it's all you got, pop it in and ride to the bike shop or W*lmart to get a size closer to your tire, then keep the undersized one as a spare.
#5
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,186
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,307 Times
in
1,117 Posts
I agree with KerryIrons. If something gets through the tire, the minuscule difference in tube stretch probably isn't going to be the make or break factor in getting a flat. If I had to choose a tube a size larger or size smaller, I'd rather have the smaller for ease of mounting and being less likely to get pinched.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
#6
Senior Member
Join Date: May 2003
Location: Mountain Brook. AL
Posts: 4,002
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 303 Post(s)
Likes: 0
Liked 136 Times
in
104 Posts
OTOH rubber is a material that stretches most where weak or thin, so any areas of thinning or any
scratch on the rubber will disproportionately thin out more increasing the risk of puncture or leak.
Probability is you will be ok but depends on individual tube factors. (Once had a bent with 406
wheels with a 34mm tire and 25mm tube with microcuts all over it, tube flatted every ride
for 5 rides -slow learner- til I looked it over and noted the microcuts and tossed it).
scratch on the rubber will disproportionately thin out more increasing the risk of puncture or leak.
Probability is you will be ok but depends on individual tube factors. (Once had a bent with 406
wheels with a 34mm tire and 25mm tube with microcuts all over it, tube flatted every ride
for 5 rides -slow learner- til I looked it over and noted the microcuts and tossed it).
#7
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
I've had good results using 18 to 28 mm tubes in 32 mm wide tyres.
Going for 37 mm was stretching it a bit and, depending on the pressure, tube getting stretched open can happen (tried it, with varying success, but wouldn't recommend it).
Yes, I'm aware that tubes do stretch quite much over their stated max tyre width, but it appears they don't really "like" being stretched too much.
Now, the question is: is the difference between 35 mm (if we assume that's what 35 c means) to 44 mm enough of a difference to make a difference.
I have no idea.
I'd feel comfortable using such a tube in a 37, or even a 40 mm wide tyre, but considering the cost of tubes, I might be tempted to give it a test with a 44 mm wide tyre only if I had no other use (wheel) for it. Just not on the front wheel.
Going for 37 mm was stretching it a bit and, depending on the pressure, tube getting stretched open can happen (tried it, with varying success, but wouldn't recommend it).
Yes, I'm aware that tubes do stretch quite much over their stated max tyre width, but it appears they don't really "like" being stretched too much.
Now, the question is: is the difference between 35 mm (if we assume that's what 35 c means) to 44 mm enough of a difference to make a difference.
I have no idea.
I'd feel comfortable using such a tube in a 37, or even a 40 mm wide tyre, but considering the cost of tubes, I might be tempted to give it a test with a 44 mm wide tyre only if I had no other use (wheel) for it. Just not on the front wheel.
Likes For Bike Gremlin:
#8
Senior Member
Join Date: Sep 2015
Location: /dev/null
Posts: 675
Bikes: Soma Double Cross Disc (2017), red Hardrock FS (circa 1996)
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 217 Post(s)
Liked 155 Times
in
102 Posts
Some discussion of possible problems with thin tubes in wide tires in this thread: https://www.bikeforums.net/bicycle-m...cher-flat.html
#9
Senior Member
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Liked 1,200 Times
in
760 Posts
It'll work because butyl tubes have the ability to stretch several times their unstretched size. However, the tube is stretched much thinner so flats will be more likely. If it's all you got, pop it in and ride to the bike shop or W*lmart to get a size closer to your tire, then keep the undersized one as a spare.
Anything that pierces the tire itself, will puncture a tube regardless of whether it's a tiny bit more stretched than a larger tube.
Also, getting a tube into a tire and that tire mounted is much easier with a smaller tube, much less to get pinched between the tire bead and the rim.