Go Back  Bike Forums > Bike Forums > Folding Bikes
Reload this Page >

Any experience with lighter square taper cranks?

Notices
Folding Bikes Discuss the unique features and issues of folding bikes. Also a great place to learn what folding bike will work best for your needs.

Any experience with lighter square taper cranks?

Old 11-27-23, 02:57 AM
  #1  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts
Any experience with lighter square taper cranks?

I have converted my 7-speed Tern to 9-speed with a new wheelset from AliExpress. Itís been an excellent upgrade; the bike is however very slightly over geared, so I am considering a new crankset.

Have any of you upgraded or swapped out your crank and bottom bracket from the supplied square taper Tern one?

Are there any major pitfalls doing this? It all looks fairly standard, without weird proprietary standards.

AliExpress offer cheap and light cranksets. After the positive experience with the wheels I am considering getting the crank there too. Any recommendations?

In an ideal world I would also like a slightly lighter option, as the combined weight of bike plus bag (Dahon Airporter) means I canít add as much luggage as I would like!

thanks all!

Simon
Barchettaman is offline  
Old 11-27-23, 02:59 AM
  #2  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts



Barchettaman is offline  
Likes For Barchettaman:
Old 11-27-23, 02:59 AM
  #3  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts
We all like photos of bikes, so here are a few of it post-wheelset upgrade. Itís a Link B7 I think
Barchettaman is offline  
Old 11-27-23, 05:47 AM
  #4  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Several years ago I swapped out the Square Taper BB on my Dahon Dash for a Hollowtech 2 one. Removing a ST BB requires a crank arm extraction tool and then a wrench for the BB shellb itself. If you are gonna do it yourself, you'll need those two tools. Hollowtech simply screws on the BB shell threads, but you'll need a HT 2 wrench to tighten. You'll want a HT2 BB for 68 BSA threads. I default to the Ultegra/105 level Shimano BBR60 which sells for under $20 in my locality




I've used Litepro HT2 cranks, chainrings and bolts since 2016 without any problems so I recommend those items. Go with the steel bolts rather than the ones from 7075 Al.


Litepro crank and chainring in continuous service since 2016 across two bikes and four countries
Ron Damon is offline  
Likes For Ron Damon:
Old 11-27-23, 10:21 AM
  #5  
Jipe
Senior Member
 
Join Date: Feb 2017
Posts: 1,542
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 800 Post(s)
Likes: 0
Liked 247 Times in 211 Posts
Originally Posted by Ron Damon
Several years ago I swapped out the Square Taper BB on my Dahon Dash for a Hollowtech 2 one. Removing a ST BB requires a crank arm extraction tool
You do not necessarily need a crank arm extraction tool, self extracting crank bolts for square taper also do the job.
Jipe is offline  
Old 11-27-23, 10:59 AM
  #6  
seat_boy
Senior Member
 
Join Date: Jul 2005
Location: Dublin, OH
Posts: 576

Bikes: Serial bike flipper

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 93 Post(s)
Liked 116 Times in 73 Posts
I've used the Litepro crank on my Bike Friday for the last few years, no complaints here.

OK, one complaint: they advertised the ring as narrow wide, but it's not really. But the crank itself is OK, nothing fancy.

Last edited by seat_boy; 11-27-23 at 07:45 PM.
seat_boy is offline  
Likes For seat_boy:
Old 11-27-23, 04:25 PM
  #7  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Litepro offers both straight-narrow and normal chainrings. I should know for I've installed and used both types. I, myself, always buy the crankarms and the chainring separately, both of which are offered in a few different styles and specs.
.

Litepro chainring, wide-narrow sans chainguard
.


Litepro chainring, normal with integrated chainguard
.

Oh yeah, make sure the bolts you purchase match the drive configuration. 1x bolts for 1x, 2x bolts for 2x.

Last edited by Ron Damon; 11-27-23 at 06:41 PM.
Ron Damon is offline  
Likes For Ron Damon:
Old 11-27-23, 05:43 PM
  #8  
tds101 
55+ Club,...
 
tds101's Avatar
 
Join Date: Aug 2012
Location: Somewhere in New York, NY
Posts: 4,318

Bikes: 9+,...

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 1111 Post(s)
Liked 843 Times in 587 Posts
I love IitePro parts. The quality is better than most, and the pricing is excellent...even here in the USA.
__________________
If it wasn't for you meddling kids,...
tds101 is offline  
Likes For tds101:
Old 11-27-23, 07:46 PM
  #9  
seat_boy
Senior Member
 
Join Date: Jul 2005
Location: Dublin, OH
Posts: 576

Bikes: Serial bike flipper

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 93 Post(s)
Liked 116 Times in 73 Posts
Does Litepro make an actual NW ring with the integrated chainguard? I've grown to like the chainguard on mine, though I would probably like the NW ring more.


(I had the ring on backwards in the above picture, in an attempt to keep the chain from falling off every time I folded my BF. It didn't help, and I dropped the chain a few times every ride. This setup didn't last long, but I like the background in this picture )
seat_boy is offline  
Old 11-27-23, 07:53 PM
  #10  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Originally Posted by seat_boy
Does Litepro make an actual NW ring with the integrated chainguard?...
Not that I know of. The ones with the integrated chain guard are the original, classic chainrings. I still like their simple aesthetic the most.
Ron Damon is offline  
Old 11-27-23, 08:36 PM
  #11  
jfouellette
Full Member
 
Join Date: Aug 2021
Location: Montreal
Posts: 391

Bikes: 1999 Bike friday NWT, 2009 Bike Friday Tikit, 2023 silverock Dewy, 2008 Dahon Smooth Hound, 2023 Litepro Trifold

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 191 Post(s)
Liked 229 Times in 139 Posts
I have four Litepro crankwheels. They have been reliable. Two are on square taper BB and two on hollowtec.



jfouellette is offline  
Likes For jfouellette:
Old 11-28-23, 03:31 AM
  #12  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts
Brilliant ideas, many thanks.

This isnít the most important consideration, and I known itís impossible to get an accurate answer as I havenít weighed whatís on the bike, but can anyone give me an APPROXIMATE weight saving if I go to Hollowtech or LitePro?

thanks all once again.
Barchettaman is offline  
Old 11-28-23, 04:53 PM
  #13  
50PlusCycling
Senior Member
 
50PlusCycling's Avatar
 
Join Date: Mar 2018
Posts: 1,124
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 551 Post(s)
Liked 806 Times in 407 Posts
I swapped out the square taper crank set on my Birdy, and bolted in a Shimano Dura Ace system with the Hollow Tech bottom bracket. No other mod I did helped so much to lighten the bike, the Hollow Tech parts weighed half as much as the original parts.
50PlusCycling is offline  
Old 11-28-23, 05:00 PM
  #14  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Well, for example, the Goode ole' Shimano BB-UN55 ST BB weighs 300g while the BBR60 HT2 BB weighs about 80g so there's that. But, on the plus side, you gotta take into account the weight of the spline on the HT2 crank.
Ron Damon is offline  
Old 11-29-23, 02:06 AM
  #15  
Jipe
Senior Member
 
Join Date: Feb 2017
Posts: 1,542
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 800 Post(s)
Likes: 0
Liked 247 Times in 211 Posts
Originally Posted by Barchettaman
Brilliant ideas, many thanks.

This isn’t the most important consideration, and I known it’s impossible to get an accurate answer as I haven’t weighed what’s on the bike, but can anyone give me an APPROXIMATE weight saving if I go to Hollowtech or LitePro?

thanks all once again.


Its impossible to tell exactly without knowing the weight of your original crankset and making a choice of a new crankset because there are huge weight differences between different crankset models but you can expect at least 300g if you buy a relatively lightweight new crankset and chainring.

I saved more than that on my Brompton by swapping the original Brompton crankset for a Tune Bigfoot square taper (its not available anymore but there are many Chinese copies of this crankset) and replacing the original BB with a TI part workshop titanium axle BB for Brompton.
Jipe is offline  
Old 11-29-23, 10:22 AM
  #16  
Tourist in MSN
Senior Member
 
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,195

Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.

Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 3458 Post(s)
Liked 1,465 Times in 1,143 Posts
Originally Posted by Jipe
You do not necessarily need a crank arm extraction tool, self extracting crank bolts for square taper also do the job.
If you get one of these, make sure that the black rings that thread into the crankset are tight and you may consider using a thread locker to make sure they stay there.

I used those on my heavy touring bike several years ago for a month long tour. I have to remove both crank arms to fit my bike into the S&S case. But one of the black rings self extracted somewhere in the middle of Iceland. When I went to remove both crank arms, discovered one was missing. That meant I had to remove the other one to move to the other side of the crank when I lacked the proper tools to do that. Since then I now carry a real proper crank arm removal instead of the self extracting crank bolts.
Tourist in MSN is offline  
Old 11-29-23, 04:49 PM
  #17  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Originally Posted by Tourist in MSN
If you get one of these, make sure that the black rings that thread into the crankset are tight and you may consider using a thread locker to make sure they stay there.

I used those on my heavy touring bike several years ago for a month long tour. I have to remove both crank arms to fit my bike into the S&S case. But one of the black rings self extracted somewhere in the middle of Iceland. When I went to remove both crank arms, discovered one was missing. That meant I had to remove the other one to move to the other side of the crank when I lacked the proper tools to do that. Since then I now carry a real proper crank arm removal instead of the self extracting crank bolts.
Do you mean to tell us that the self extracting bolt self extracted? 😆

To be fair, though, I've heard plenty of stories from folks with HT2 cranks whose non-drive side crank arm simply feel off while pedaling, enduring insufferable embarrassment, cuz the main bolt had unscrewed. Note that unlike pedal threads, the main HT2 crank arm bolt on the non-drive side, is threaded normally, meaning that it unscrews in the same direction as the pedaling motion.

Last edited by Ron Damon; 01-08-24 at 11:46 PM.
Ron Damon is offline  
Old 11-29-23, 07:51 PM
  #18  
Tourist in MSN
Senior Member
 
Join Date: Aug 2010
Location: Madison, WI
Posts: 11,195

Bikes: 1961 Ideor, 1966 Perfekt 3 Speed AB Hub, 1994 Bridgestone MB-6, 2006 Airnimal Joey, 2009 Thorn Sherpa, 2013 Thorn Nomad MkII, 2015 VO Pass Hunter, 2017 Lynskey Backroad, 2017 Raleigh Gran Prix, 1980s Bianchi Mixte on a trainer. Others are now gone.

Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
Quoted: 3458 Post(s)
Liked 1,465 Times in 1,143 Posts
Originally Posted by Ron Damon
Do you mean to tell us that the self extracting bolt self extracted? 😆
.....
Yup, as I said: But one of the black rings self extracted somewhere in the middle of Iceland.



As I noted, using a threadlocker would probably prevent it from falling out. I did not suggest more detail, as the OP is in Germany and I do not know what brands of thread locker is sold there. But the removable (blue) would be best.

Originally Posted by Ron Damon
...
To be fair, though, I've heard plenty of stories from folks with HT2 cranks whose non-drive side crank arm simply feel off while pedaling, enduring insufferable embarrassment, cuz the main bolt had unscrewed. Note that unlike pedal threads, the main HT2 crank arm bolt on the non-drive side, is threaded normally, meaning that it unscrews in the same direction as the pedaling motion.

While in the topic, one minus of the Litepro HT2 cranks is they come with a main bolt made out of plastic with a nonstandard pattern. I always replace it with an aftermarket bolt made of out Al alloy with a hex pattern that can be turned with an ubiquitous Allen key. M18 is the thread size of the bolt you'll want to buy for Litepro HT2 cranks.
Not sure what an HT2 crank is.

Many years ago a friend was out for a bike ride, he later told me that as he was riding, he suddenly heard someone swearing loudly. He looked over and saw a bicyclist with a crank arm hanging down from his foot. That was in the toe clip era, before shoe cleats.

I have square taper cranks on most of my bikes, but my road bike that I bought as a complete bike has a Campy Power Torque. All the bikes I built up from parts, which is most of them, have square taper.
Tourist in MSN is offline  
Old 11-29-23, 08:04 PM
  #19  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Hollowtech 2 (HT2)


Replacement metal bolt

Last edited by Ron Damon; 11-30-23 at 11:15 PM.
Ron Damon is offline  
Likes For Ron Damon:
Old 01-09-24, 04:05 AM
  #20  
Duragrouch
Senior Member
 
Join Date: Apr 2017
Posts: 1,615
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 726 Post(s)
Liked 405 Times in 323 Posts
I agree with others, and strongly recommend replacing a square taper bottom bracket, with a hollowtech II style crank (but NOT Shimano, there is a recall on many, come apart, a spider bonded (glued, or mashed together under pressure) to the chainring).

External bearings last longer, both because larger and/or more balls per side, and spaced further apart, but also because you can periodically readjust the bearing preload to take up slack; you can't do that with a cartridge square taper BB (you can with old style non-cartridge, but it's a pain), and once loose, wear accelerates; proper preload (zero slack) is key. The crank does not freeze up on the taper due to corrosion, or work its way loose due to putting anti-seize or grease on the taper. Very easy to remove the crank for cleaning.

My preference is retro 5 bolt on 110mm bolt circle diameter, with replaceable chainrings. I'm currently using a 50/34 that came complete with external bearings for about USD $75, equal or less cost than 2 chainrings alone. The bearing spline style is "ISO external", quite common. I'd recommend a bearing wrench that has the 4 most common styles, it's only slightly more expensive than a 2 or 3 way wrench, and you're set for life.
Duragrouch is online now  
Old 03-07-24, 09:04 AM
  #21  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts
Iíve gone with a Litepro 47t square taper crankset, for Ä33,50 it seemed like a decent deal.

I might convert the whole rig to drop bars too as I have the parts (drop bar with MTB clamp diameter, 9-speed Shimano STI shifter, a travel agent, a Tektro long pull drop bar lever) in the parts bin.

I just need to check that itíll fit OK in the Dahon Airporter suitcase with the drop bars as I travel with this a lot.
Barchettaman is offline  
Old 03-07-24, 11:58 PM
  #22  
Duragrouch
Senior Member
 
Join Date: Apr 2017
Posts: 1,615
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 726 Post(s)
Liked 405 Times in 323 Posts
Originally Posted by Barchettaman
Iíve gone with a Litepro 47t square taper crankset, for Ä33,50 it seemed like a decent deal.

I might convert the whole rig to drop bars too as I have the parts (drop bar with MTB clamp diameter, 9-speed Shimano STI shifter, a travel agent, a Tektro long pull drop bar lever) in the parts bin.

I just need to check that itíll fit OK in the Dahon Airporter suitcase with the drop bars as I travel with this a lot.
If the handlebar clamp opens up like a clamshell so drop bars easily removable, my guess is it should fit that way, if not fully assembled.

I have an early Dahon stem without a clamshell clamp, so would take an hour to pull apart and an hour to reassemble. I may have to upgrade that if I travel; no drop bars, but do have flat bar with bar-ends and clip-on aero bar, which makes for a bigger fold because that stem folds between the frame halves. But the telescoping stem is weaker. I'll look for a tall fixed stem with clamshell clamp.
Duragrouch is online now  
Old 03-08-24, 01:09 AM
  #23  
Barchettaman
Senior Member
Thread Starter
 
Barchettaman's Avatar
 
Join Date: Oct 2008
Location: Frankfurt, Germany
Posts: 1,544

Bikes: Focus trash find commuter, Eddy Merckx Corsa, BP Stealth TT bike, Leader 720 TT bike, Boardman Comp Hybrid drop bar conversion, Quantec CX budget cyclocross build, SerottaNOS frameset ready to build up!

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Liked 104 Times in 69 Posts
When I got the bike I found the reach at the bars too short and the handling very twitchy. I ended up with a stem extender from AliExpress which works superbly well:



I highly recommend this mod; it transforms the handling and comfort of the bike. I know thereís an Andros stem extender from Tern but it was incompatible with my handlebar post.

I need to check if the 25.4 drop bar has a wide enough clamp diameter for this extender, and if so, I will have a look at swapping them in.
Barchettaman is offline  
Old 03-08-24, 03:10 AM
  #24  
Duragrouch
Senior Member
 
Join Date: Apr 2017
Posts: 1,615
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 726 Post(s)
Liked 405 Times in 323 Posts
Originally Posted by Barchettaman
When I got the bike I found the reach at the bars too short and the handling very twitchy. I ended up with a stem extender from AliExpress which works superbly well:



I highly recommend this mod; it transforms the handling and comfort of the bike. I know thereís an Andros stem extender from Tern but it was incompatible with my handlebar post.

I need to check if the 25.4 drop bar has a wide enough clamp diameter for this extender, and if so, I will have a look at swapping them in.
Yes, putting the bars further forward helps stability, both by putting that mass further forward of the steering axis, and your hand force causing a more "centering" feel; My handlebars are centered on the stempost but are still forward of the steering axis as the stempost is canted forward from the steering axis.

Yes, width of clamp diameter on bars can be a problem, both for that, and for typical clip-on aero bars that don't mount close to the stem clamp; clamping on the smaller diameter is possible with shims, but problematic if clamping in the transition (tapered) area between diameters. If aeros clamp close to the stem, then they prevent use of a stem extender like you have. I have aero clip-ons.

I saw some of those extenders on amazon, but most looked much less stout than the Tern part, which is expensive; The parts will be subjected to significant torsion loads when climbing, in addition to normal bending loads. Some looked like they were designed just to mount a short bar for accessories like lights and computer, but not transfer handlebar loads to the stem. But again, I can't use due to my aero bars. Also, my current reach is perfect.

What I would like to fit, and would be worth the cost, is one of those parallel-link suspension stems, which my current stempost will not accommodate, but even if I get one that does, I don't want the bars further forward, which that stem would do. A stempost more tilted back would correct that, but then is more likely to get hit with my knees when climbing.

Last edited by Duragrouch; 03-08-24 at 03:24 AM.
Duragrouch is online now  
Old 03-08-24, 04:01 AM
  #25  
Ron Damon
Senior Member
 
Join Date: Jun 2022
Location: The Ring of Fire
Posts: 928
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 461 Post(s)
Liked 566 Times in 355 Posts
Originally Posted by Barchettaman
When I got the bike I found the reach at the bars too short and the handling very twitchy. I ended up with a stem extender from AliExpress which works superbly well:



I highly recommend this mod; it transforms the handling and comfort of the bike. I know there’s an Andros stem extender from Tern but it was incompatible with my handlebar post.

I need to check if the 25.4 drop bar has a wide enough clamp diameter for this extender, and if so, I will have a look at swapping them in.
Another, perhaps simpler way to add reach is use a riser bar rotated forwards.

An advantage of this approach is that whereas stem of the sort above are kinda limited in size, riser handlebars come in a myriad of rises. You need 9cm of additional reach, no problem. Ridiculous, yes, but you can simply get a 9cm riser bar.

Last edited by Ron Damon; 03-08-24 at 04:58 AM.
Ron Damon is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.