Seat tube and head tube - torque specifications
#1
Senior Member
Thread Starter
Join Date: Jul 2017
Location: Pacific Northwest
Posts: 1,993
Bikes: Argon 18 Gallium, BH G7, Rocky Mountain Instinct C70
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 800 Post(s)
Liked 512 Times
in
306 Posts
Seat tube and head tube - torque specifications
Does anyone know the torque specifications for the following? The integrated seat post in my Aerolight and the head tube/stem? I've done some searching online and I cannot find the information. I also contacted the bike shop and they are not getting back to me, so I am at a loss.
The stem is an EVO Monocoque ACR
The headset is FSA ACR
Thank you for your help.
The stem is an EVO Monocoque ACR
The headset is FSA ACR
Thank you for your help.
#2
Senior Member
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,925
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1819 Post(s)
Liked 1,693 Times
in
974 Posts
The top cap bolt is only tightened until play is taken out of the headset after which the pinch bolts are tightened to the correct torque
#3
LR÷P=HR
Join Date: Sep 2019
Location: SF Bay Area
Posts: 2,180
Bikes: 1981 Holdsworth Special, 1993 C-dale MT3000 & 1996 F700CAD3, 2018 Cervelo R3 & 2022 R5, JustGo Runt, Ridley Oval, Kickr Bike 8-)
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 867 Post(s)
Liked 1,204 Times
in
693 Posts
Have you tried BH directly?
Barry
Barry
#4
LR÷P=HR
Join Date: Sep 2019
Location: SF Bay Area
Posts: 2,180
Bikes: 1981 Holdsworth Special, 1993 C-dale MT3000 & 1996 F700CAD3, 2018 Cervelo R3 & 2022 R5, JustGo Runt, Ridley Oval, Kickr Bike 8-)
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 867 Post(s)
Liked 1,204 Times
in
693 Posts
OK, OK, I broke down and went and looked for you.....
HERE YOU GO
It's the number one hit when Googling BH EVO Mono ACR Stem instructions
The instructions actually state not only the Torque figures but.... "Do not go above maximum torque rating printed on the stem."
I suspect you'll find it on the Stem if you look, it's usually hidden underneath.
Captain Obvious signing off
HERE YOU GO
It's the number one hit when Googling BH EVO Mono ACR Stem instructions
The instructions actually state not only the Torque figures but.... "Do not go above maximum torque rating printed on the stem."
I suspect you'll find it on the Stem if you look, it's usually hidden underneath.
Captain Obvious signing off
#5
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
As posted above there is no torque setting for the top cap. The stem clamp bolts are most likely 5.0-5.2nm like nearly other stem on the planet that uses M5 bolts. I have no idea about the seat post, but I'd remove it from the frame and see if there's anything printed on the post itself.
Likes For cxwrench:
#8
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts