Bike storage from joists
#26
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,490
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2716 Post(s)
Liked 3,332 Times
in
2,024 Posts
That may be true. What I was thinking was not flat against the joists, but spanning them, sort of flat parallel to the WALL.
Honestly, re: the screwing upward hooks into the undersides... I just didn't think it was the most secure way to do it! I've never used those before and thought it would be more secure to use a loop of material to go through the hole than to trust the screw threads in the wood. Needless to say, I'm not an engineer, and It sounds like everyone who knows does it and trusts 'em.
Honestly, re: the screwing upward hooks into the undersides... I just didn't think it was the most secure way to do it! I've never used those before and thought it would be more secure to use a loop of material to go through the hole than to trust the screw threads in the wood. Needless to say, I'm not an engineer, and It sounds like everyone who knows does it and trusts 'em.
https://qis-tx.com/Newsletters/0605/
Likes For dedhed:
#27
Senior Member
Join Date: Dec 2006
Location: Houston, TX
Posts: 895
Bikes: 2017 Co-op ADV 1.1; ~1991 Novara Arriba; 1990 Fuji Palisade; mid-90's Moots Tandem; 1985 Performance Superbe
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 383 Post(s)
Liked 559 Times
in
325 Posts
Example
I lift rear wheel up and hang it first, then the front wheel.
#28
Senior Member
Join Date: Feb 2007
Location: Schwenksville, Pa
Posts: 2,859
Bikes: '80 Mercian Olympic, '82 Kabuki GranKabuki,92 DB Overdrive, '07 Rivendell AHH, '16 Clockwork All-Rounder, '22 New Albion Privateer
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 273 Post(s)
Liked 338 Times
in
178 Posts
My thought was, get a 1"x2" and cut it about 4" wider than the hole. Tie a rope to the center of it and push it through the hole leaving the rope to dangle on the opposite side of the stick with a noose just below the rafter. The 1"x2" will achor on eother side of the hole and you can hang the bikes saddle from the noose.
__________________
#29
Senior Member
Join Date: Apr 2007
Posts: 6,735
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1089 Post(s)
Liked 1,187 Times
in
750 Posts
That may be true. What I was thinking was not flat against the joists, but spanning them, sort of flat parallel to the WALL.
Honestly, re: the screwing upward hooks into the undersides... I just didn't think it was the most secure way to do it! I've never used those before and thought it would be more secure to use a loop of material to go through the hole than to trust the screw threads in the wood. Needless to say, I'm not an engineer, and It sounds like everyone who knows does it and trusts 'em.
Honestly, re: the screwing upward hooks into the undersides... I just didn't think it was the most secure way to do it! I've never used those before and thought it would be more secure to use a loop of material to go through the hole than to trust the screw threads in the wood. Needless to say, I'm not an engineer, and It sounds like everyone who knows does it and trusts 'em.
No, you don't have to worry about strength. If you're unsure, put one in, and grab it and hang and try with all your might to pull it out! It's always best to drill a hole to screw the hook into if you can.
Likes For Camilo: