Are these fork/stem races removeable? Worth the trouble?
#1
Member
Thread Starter
Are these fork/stem races removeable? Worth the trouble?
I would like to remove the aluminum races from the frame so I can clean/polish them. I think they're are quite likely stuck, if they're even removeable at al. I don't want to risk damaging them if removal is too difficult.
Thoughts?
Thoughts?
#2
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,091 Times
in
722 Posts
I suspect that they are steel, judging by the red rust. Check with a magnet.
#3
Member
Thread Starter
#4
Made in Taiwan
Join Date: Sep 2008
Location: Vancouver
Posts: 214
Bikes: Camerotti ti roadbike, Old Sears Free Spirit Tange Hi-Ten Single Speed built from a 12 speed, 1997 Cannondale CAD3 r500 with Shimano 6400 groupset
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 35 Post(s)
Liked 11 Times
in
9 Posts
Those are headset cups, there is a specific tool used to hammer them out so that pressure is applied evenly all the way around.
If you don't have access to such a tool or don't want to make your own. You can use a large flat head screw driver and hammer to tap out the cups. However, if you remove the cups, the bigger problem is getting them seated again or pressed back into your frame.
Please, do a google search on on 1) headset cup removal and 2) headset cup installation. Better yet, watch some youtube videos.
If you don't know what you are doing, you can damage your bike/parts.
If you don't have access to such a tool or don't want to make your own. You can use a large flat head screw driver and hammer to tap out the cups. However, if you remove the cups, the bigger problem is getting them seated again or pressed back into your frame.
Please, do a google search on on 1) headset cup removal and 2) headset cup installation. Better yet, watch some youtube videos.
If you don't know what you are doing, you can damage your bike/parts.
__________________
All dogs want to be lap dogs doesn't matter the size
-Animal loving friend
All dogs want to be lap dogs doesn't matter the size
-Animal loving friend
Likes For *Scuba:
#5
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,091 Times
in
722 Posts
Never Fix A Running Piece. I am not sure what you could do in the way of cleaning/polishing the cups after removal that you could not do in situ.
#6
Member
Thread Starter
#7
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
Just google search 'headset cup removal'...you'll get thousands of results in a fraction of a second. It's easy w/ the correct tool.
Likes For cxwrench:
#8
Member
Thread Starter
Those are headset cups, there is a specific tool used to hammer them out so that pressure is applied evenly all the way around.
If you don't have access to such a tool or don't want to make your own. You can use a large flat head screw driver and hammer to tap out the cups. However, if you remove the cups, the bigger problem is getting them seated again or pressed back into your frame.
Please, do a google search on on 1) headset cup removal and 2) headset cup installation. Better yet, watch some youtube videos.
If you don't know what you are doing, you can damage your bike/parts.
If you don't have access to such a tool or don't want to make your own. You can use a large flat head screw driver and hammer to tap out the cups. However, if you remove the cups, the bigger problem is getting them seated again or pressed back into your frame.
Please, do a google search on on 1) headset cup removal and 2) headset cup installation. Better yet, watch some youtube videos.
If you don't know what you are doing, you can damage your bike/parts.
#9
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,911
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3556 Post(s)
Liked 3,332 Times
in
1,899 Posts
But keep in mind you'll need another "correct tool" to reinstall them properly.
If the goal is merely to remove the surface rust for cosmetic reasons, leave them in place and rub with crumpled aluminum foil or a scotch-brite™ pad to get rid of the rust.
#10
Senior Member
Join Date: Nov 2014
Location: Eastern Iowa
Posts: 631
Bikes: 2014 Trek Allant drop bar conversion, modified Schwinn MTN commuter, 2015 Trek 520, Soma ES, Salsa Journeyman, 1980 Trek 414
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 178 Post(s)
Liked 355 Times
in
166 Posts
Mask off the headtube to protect it and polish the cups while they are still installed. You will not get them any cleaner by removing them from the headtube - the only part that is inaccessible is the part of the cups that are pressed against the inside of the headtube, and you don't want to polish that anyway. You also risk damage to the cups and frame if you do not have the proper removal and re-installation tools.
Likes For SalsaShark:
#12
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,106
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,412 Times
in
799 Posts
There are homemade tools that can accomplish the removal and installation of the cups. One source is RJ the bike guy on youtube. I used his tool ideas for that, and they worked OK. You just need to take your time and make sure things are progressing properly. However, I did end up buying a removal tool and a headset press as I had other bikes to do. I bought both tools during a sale at Chain Reaction Cycles.com. IIRC, it was about $80 usd for both. The prices have gone up since I purchased. If this is a onetime deal, the cost is probably not worth it.
As stated above, I think you could accomplish what you want without removing the cups. If you are just touching up the paint on the frame, no need to remove the cups.
As stated above, I think you could accomplish what you want without removing the cups. If you are just touching up the paint on the frame, no need to remove the cups.
Likes For delbiker1: