Rockbros sucker rack
#1
Senior Member
Thread Starter
Join Date: Feb 2019
Posts: 330
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 57 Times
in
40 Posts
Rockbros sucker rack
Any experience? Positives/negatives? It's ~$120 less than a Seasucker; Prime shipping; and returns until Jan 2021. Is this a good area to save some coin, or is this a terrible idea to "cheap out" on? [straps muli-thousand dollar bike using $180 bike mount] 😄
#2
Senior Member
A proper bike rack is not that expensive.
#3
Senior Member
Join Date: Jan 2010
Location: TC, MN
Posts: 39,520
Bikes: R3 Disc, Haanjo
Mentioned: 354 Post(s)
Tagged: 1 Thread(s)
Quoted: 20810 Post(s)
Liked 9,456 Times
in
4,672 Posts
No experience, but with the visual suction indicators and a bit of redundancy, I wouldn't be too worried. I mean, I'd still be a little nervous the first time around, and I'd be somewhat OCD about checking on the indicators any time that I used it, but I'd still use it if I couldn't use a conventional rack.
#4
Senior Member
Thread Starter
Join Date: Feb 2019
Posts: 330
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 57 Times
in
40 Posts
I've been using the strap-on Allen, trunk bike rack, but since the addition of deep section wheels the bike flutters and slaps the trunk. I use bungee cords to hold the bike frame to the mount, as well as to hold the front wheel steady. At freeway speeds it still moves around. I figure having the bike inline with the wind, and tethered by the fork dropout, would steady the bike.
As stated by Whyfi, the redundancy in the front suction cups helps alleviate worry, and I would double-triple check the suction cups anytime I make a stop. I've scoured the web for negative reviews and I've only found one or two, where someone claimed the aluminum base plate cracked or that the suction cups cracked their windshield.
As stated by Whyfi, the redundancy in the front suction cups helps alleviate worry, and I would double-triple check the suction cups anytime I make a stop. I've scoured the web for negative reviews and I've only found one or two, where someone claimed the aluminum base plate cracked or that the suction cups cracked their windshield.
Likes For Elvo:
#6
Senior Member
Join Date: Oct 2016
Location: San Mateo,Ca.
Posts: 3,985
Bikes: TRIMMED DOWN THE HERD
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1091 Post(s)
Liked 936 Times
in
601 Posts
Definitely a bad idea! I'd spend for a Sea Sucker if it's really worth it(I wouldn't use a suction rack,IMO).
#7
Junior Member
Join Date: Aug 2016
Posts: 100
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 9 Times
in
8 Posts
I have a Rockbros sucker rack. No complaints - only mod I did was a bit of threadlocker on the bolts. Make sure the roof and suction cups are clean and you shouldn't have an issue. Check the indicators at every stop, though.
I haven't take it on a 500+ mile journey, but I did take it around the I275 loop of Cincinnati - about 90 miles. I stopped once and everything was holding as it should.
I haven't take it on a 500+ mile journey, but I did take it around the I275 loop of Cincinnati - about 90 miles. I stopped once and everything was holding as it should.
#8
Senior Member
Thread Starter
Join Date: Feb 2019
Posts: 330
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 57 Times
in
40 Posts
I have a Rockbros sucker rack. No complaints - only mod I did was a bit of threadlocker on the bolts. Make sure the roof and suction cups are clean and you shouldn't have an issue. Check the indicators at every stop, though.
I haven't take it on a 500+ mile journey, but I did take it around the I275 loop of Cincinnati - about 90 miles. I stopped once and everything was holding as it should.
I haven't take it on a 500+ mile journey, but I did take it around the I275 loop of Cincinnati - about 90 miles. I stopped once and everything was holding as it should.
#9
Senior Member
Thread Starter
Join Date: Feb 2019
Posts: 330
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 57 Times
in
40 Posts
I just took a quick look at those items. The 1upusa is sold out until Nov and has a higher associated cost. The Kuat nv uses a tow hitch, which isn't something I'm looking for. I like the idea of suction cup mounts because of its versatility and ease of transport.
#14
well hello there
Join Date: May 2005
Location: Point Loma, CA
Posts: 15,430
Bikes: Bill Holland (Road-Ti), Fuji Roubaix Pro (back-up), Bike Friday (folder), Co-Motion (tandem) & Trek 750 (hybrid)
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 503 Post(s)
Liked 336 Times
in
206 Posts
If that's true, that would be a deal breaker for me right there. No way I'm going to be forced to clean my vehicle's roof every time I use a bike rack, or face the possibility of rack failure.
__________________
.
.
Two wheels good. Four wheels bad.
.
.
Two wheels good. Four wheels bad.
#15
Senior Member
Join Date: Jan 2010
Posts: 39,229
Mentioned: 211 Post(s)
Tagged: 1 Thread(s)
Quoted: 18409 Post(s)
Liked 15,520 Times
in
7,324 Posts
#17
Junior Member
Join Date: Aug 2016
Posts: 100
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 9 Times
in
8 Posts
Yes, the single rear cup can be a point of failure, but I think they take that into account. It would be easy enough to design a mount with two cups for a single bike, but they don't.
Even if it fails what's the worst that happens? There's still friction between the cup and the roof so it shouldn't slide around too much. If you hit a bump, maybe the rear wheel comes up off the roof?
John
Even if it fails what's the worst that happens? There's still friction between the cup and the roof so it shouldn't slide around too much. If you hit a bump, maybe the rear wheel comes up off the roof?
John
#18
Senior Member
Join Date: Nov 2015
Posts: 8,922
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 4717 Post(s)
Liked 1,882 Times
in
998 Posts
Yes, the single rear cup can be a point of failure, but I think they take that into account. It would be easy enough to design a mount with two cups for a single bike, but they don't.
Even if it fails what's the worst that happens? There's still friction between the cup and the roof so it shouldn't slide around too much. If you hit a bump, maybe the rear wheel comes up off the roof?
John
Even if it fails what's the worst that happens? There's still friction between the cup and the roof so it shouldn't slide around too much. If you hit a bump, maybe the rear wheel comes up off the roof?
John
#20
well hello there
Join Date: May 2005
Location: Point Loma, CA
Posts: 15,430
Bikes: Bill Holland (Road-Ti), Fuji Roubaix Pro (back-up), Bike Friday (folder), Co-Motion (tandem) & Trek 750 (hybrid)
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 503 Post(s)
Liked 336 Times
in
206 Posts
Just make sure to keep the surface contact areas all clean and I'm sure you won't have multiple failures.
__________________
.
.
Two wheels good. Four wheels bad.
.
.
Two wheels good. Four wheels bad.
#21
Senior Member
Thread Starter
Join Date: Feb 2019
Posts: 330
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 173 Post(s)
Liked 57 Times
in
40 Posts
Against all odds, I will be giving the IPT suction bike rack a try. It only has one, large front suction cup; it has no redundancy. I did a little research on Amazon and it would seem they specialize in these suction cup products for use as professional devices. That gives me some reassurance. The product is also within a more reasonable price range ($99) for such a product. I'll report back my findings [fingers crossed]
Likes For Princess_Allez:
#22
Junior Member
Join Date: Aug 2016
Posts: 100
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 9 Times
in
8 Posts
Against all odds, I will be giving the IPT suction bike rack a try. It only has one, large front suction cup; it has no redundancy. I did a little research on Amazon and it would seem they specialize in these suction cup products for use as professional devices. That gives me some reassurance. The product is also within a more reasonable price range ($99) for such a product. I'll report back my findings [fingers crossed]
John
#23
FLIR Kitten to 0.05C
Join Date: Sep 2014
Location: Lincoln, Nebraska
Posts: 5,331
Bikes: Roadie: Seven Axiom Race Ti w/Chorus 11s. CX/Adventure: Carver Gravel Grinder w/ Di2
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 2349 Post(s)
Liked 406 Times
in
254 Posts
Against all odds, I will be giving the IPT suction bike rack a try. It only has one, large front suction cup; it has no redundancy. I did a little research on Amazon and it would seem they specialize in these suction cup products for use as professional devices. That gives me some reassurance. The product is also within a more reasonable price range ($99) for such a product. I'll report back my findings [fingers crossed]
Likes For Marcus_Ti:
#24
Senior Member
Join Date: Sep 2009
Posts: 94
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 10 Post(s)
Likes: 0
Liked 5 Times
in
2 Posts
I use a SeaSucker on several hundred mile trips a few times a year. Interstate speeds a good bit of the time. I follow the recommendations and have never had an issue. I wouldn't want to put anything very heavy on it, but it seems to be perfectly fine for a ~16lbs road bike