Notices
General Cycling Discussion Have a cycling related question or comment that doesn't fit in one of the other specialty forums? Drop on in and post in here! When possible, please select the forum above that most fits your post!

Small Pliers

Old 03-11-22, 11:21 AM
  #1  
themp
Full Member
Thread Starter
 
Join Date: Aug 2015
Location: Raleigh, NC
Posts: 314

Bikes: Specialized Crosstrail

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 119 Post(s)
Liked 58 Times in 44 Posts
Small Pliers

I use tubes that have a metal valve and nut. I have had to use a small amount of blue thread-locker to keep the nut from spinning up as I ride. I just tighten the nut enough to keep the valve stem from flexing. However, when changing a flat on a ride I found it tough to use my fingers to remove the stem nut. To the rescue was this:

https://www.walmart.com/ip/Ozark-Tra...S401/203357977

I removed the lanyard chain to even make it smaller. Hardly takes up any space in my bag and the price is right....
themp is offline  
Likes For themp:
Old 03-11-22, 11:43 AM
  #2  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,821

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6100 Post(s)
Liked 4,734 Times in 3,264 Posts
Put that plastic cap back on and maybe the nut won't loosen itself while you ride. And you won't have to use thread locker.

However you are the first I've ever read that is having a problem with their nuts. Or at least the little nuts on the presta valve stem. <grin>

If you had to come up with an alternate solution, then what about a small diameter rubber or plastic tube you can put over both the nut and the smaller part of the stem. Maybe the insulation from some larger gauge electrical wire.

Last edited by Iride01; 03-11-22 at 11:47 AM.
Iride01 is offline  
Old 03-11-22, 12:21 PM
  #3  
Barry2 
LR÷P=HR
 
Join Date: Sep 2019
Location: SF Bay Area
Posts: 2,138

Bikes: 1981 Holdsworth Special, 1993 C-dale MT3000 & 1996 F700CAD3, 2018 Cervelo R3 & 2022 R5, JustGo Runt, Ridley Oval, Kickr Bike 8-)

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 848 Post(s)
Liked 1,163 Times in 673 Posts
No nuts

Unless the Wheel is configured as Tubeless, I throw those nuts away.
Don't toss them away on a tubeless, they ARE retaining the valve against the rim internally and creating a seal.

Barry
Barry2 is offline  
Likes For Barry2:
Old 03-11-22, 12:28 PM
  #4  
Reflector Guy
Senior Member
 
Reflector Guy's Avatar
 
Join Date: Jul 2020
Location: Chicago
Posts: 1,340

Bikes: Bianchi Infinito XE, Via Nirone 7, GT Aggressor Pro

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 599 Post(s)
Liked 1,270 Times in 588 Posts
Are we referring here to the little nut on the valve itself (which is usually hidden under the cap), or to the larger nut where the valve comes out of the rim?

I have had the latter nut loosen and ride up on the valve; I just tighten it back down by hand. It doesn't have to be enormously tight.
Reflector Guy is offline  
Likes For Reflector Guy:
Old 03-11-22, 01:12 PM
  #5  
CliffordK
Senior Member
 
CliffordK's Avatar
 
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,600
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18321 Post(s)
Liked 4,490 Times in 3,338 Posts
That nut is handy to get the pump attached at times. Otherwise, it doesn't do much. I've never paid a lot of attention to how tight it actually is when riding with the tube full of air.

Purple Loctite is weaker than blue. If you want to use some, give it a try next time.
CliffordK is offline  
Old 03-11-22, 01:24 PM
  #6  
njkayaker
Senior Member
 
Join Date: Sep 2007
Location: Far beyond the pale horizon.
Posts: 14,241
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 4222 Post(s)
Liked 1,322 Times in 916 Posts
You don't need the nut. You don't need the cap.

Push on tire on the opposite side of the valve to get the pump on.
njkayaker is offline  
Likes For njkayaker:
Old 03-11-22, 01:46 PM
  #7  
Riveting
Senior Member
 
Join Date: Oct 2013
Location: Highlands Ranch, CO
Posts: 1,221

Bikes: '13 Diamondback Hybrid Commuter, '17 Spec Roubaix Di2, '17 Spec Camber 29'er, '19 CDale Topstone Gravel

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 590 Post(s)
Liked 445 Times in 260 Posts
Originally Posted by njkayaker
You don't need the nut. You don't need the cap.

Push on tire on the opposite side of the valve to get the pump on.
This is said a lot. But the problem is that some pumps need to be secured by pushing the pump down onto the stem with one hand, while the other hand has to flip the lever 90° to secure/squeeze the pump nozzle to the stem. I personally don't have a third hand to push down on the opposite side of the tire to stop the stem from going into the rim, therefore I use the the little round nut to hold the stem in place.
Riveting is offline  
Old 03-11-22, 01:56 PM
  #8  
njkayaker
Senior Member
 
Join Date: Sep 2007
Location: Far beyond the pale horizon.
Posts: 14,241
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 4222 Post(s)
Liked 1,322 Times in 916 Posts
Originally Posted by Riveting
This is said a lot. But the problem is that some pumps need to be secured by pushing the pump down onto the stem with one hand, while the other hand has to flip the lever 90° to secure/squeeze the pump nozzle to the stem. I personally don't have a third hand to push down on the opposite side of the tire to stop the stem from going into the rim, therefore I use the the little round nut to hold the stem in place.
It's not that hard. It's what I've done for years. (I don't have three hands.)
njkayaker is offline  
Likes For njkayaker:
Old 03-11-22, 02:07 PM
  #9  
Riveting
Senior Member
 
Join Date: Oct 2013
Location: Highlands Ranch, CO
Posts: 1,221

Bikes: '13 Diamondback Hybrid Commuter, '17 Spec Roubaix Di2, '17 Spec Camber 29'er, '19 CDale Topstone Gravel

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 590 Post(s)
Liked 445 Times in 260 Posts
Originally Posted by njkayaker
It's not that hard. It's what I've done for years. (I don't have three hands.)
How do you: press down on the pump, press down on the opposite side of the tire, and flip the lever all at the same time with only two hands. I just make it easy on myself and use the nut, instead of pressing on the tire, doing it your way just seems unnecessarily masochistic.

Last edited by Riveting; 03-11-22 at 02:13 PM.
Riveting is offline  
Old 03-11-22, 02:08 PM
  #10  
spelger
Senior Member
 
spelger's Avatar
 
Join Date: Jul 2015
Location: reno, nv
Posts: 2,276

Bikes: yes, i have one

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 1124 Post(s)
Liked 1,171 Times in 682 Posts
Originally Posted by Riveting
This is said a lot. But the problem is that some pumps need to be secured by pushing the pump down onto the stem with one hand, while the other hand has to flip the lever 90° to secure/squeeze the pump nozzle to the stem. I personally don't have a third hand to push down on the opposite side of the tire to stop the stem from going into the rim, therefore I use the the little round nut to hold the stem in place.
don't have a third hand...what are you, some kind of freak?
spelger is offline  
Likes For spelger:
Old 03-11-22, 02:18 PM
  #11  
njkayaker
Senior Member
 
Join Date: Sep 2007
Location: Far beyond the pale horizon.
Posts: 14,241
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 4222 Post(s)
Liked 1,322 Times in 916 Posts
Originally Posted by Riveting
How do you: press down on the pump, press down on the opposite side of the tire, and flip the lever all at the same time with only two hands. I just make it easy on myself and use the nut, instead of pressing on the tire, doing it your way just seems unnecessarily masochistic.
I never use the nut and I use pumps with levers.

You push the head onto the stem and then flip the lever up.
njkayaker is offline  
Likes For njkayaker:
Old 03-11-22, 03:23 PM
  #12  
CliffordK
Senior Member
 
CliffordK's Avatar
 
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,600
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18321 Post(s)
Liked 4,490 Times in 3,338 Posts
Originally Posted by Riveting
How do you: press down on the pump, press down on the opposite side of the tire, and flip the lever all at the same time with only two hands. I just make it easy on myself and use the nut, instead of pressing on the tire, doing it your way just seems unnecessarily masochistic.
I've got enough fingers and thumbs that I can normally push a lever up or down without thinking about it.

There are some pumps with twist heads that may be more cumbersome.

Sometimes it will depend on the length of stem. Short stems may be barely enough to snag a tread or two. Others are so long that there are no issues.

Nonetheless, it is good to have a backup plan for those times when you're on the side of the road and all the nuts vanish into the gravel.
CliffordK is offline  
Likes For CliffordK:
Old 03-11-22, 04:33 PM
  #13  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767

Bikes: lots

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times in 1,489 Posts
Some of the threads on this forum or maybe
cxwrench is offline  
Old 03-11-22, 04:40 PM
  #14  
Iride01 
I'm good to go!
 
Iride01's Avatar
 
Join Date: Jul 2017
Location: Mississippi
Posts: 14,821

Bikes: Tarmac Disc Comp Di2 - 2020

Mentioned: 50 Post(s)
Tagged: 0 Thread(s)
Quoted: 6100 Post(s)
Liked 4,734 Times in 3,264 Posts
Originally Posted by Barry2
Unless the Wheel is configured as Tubeless, I throw those nuts away.
Don't toss them away on a tubeless, they ARE retaining the valve against the rim internally and creating a seal.

Barry
Originally Posted by Reflector Guy
Are we referring here to the little nut on the valve itself (which is usually hidden under the cap), or to the larger nut where the valve comes out of the rim?

I have had the latter nut loosen and ride up on the valve; I just tighten it back down by hand. It doesn't have to be enormously tight.
Now that I read it again, I think y'all were on the right track. I thought they were the OP was talking about the little nut you spin to prepare the valve to take air.

Makes more sense that the nut the OP must be referring to is the one that prevents the stem from getting pushed into the rim.

I wouldn't tighten that much at all, too much might start pulling the stem out of the tube. I've never worried about them getting loose.

Last edited by Iride01; 03-11-22 at 04:43 PM. Reason: changed to a singular reference instead of "they were" which gives some people trouble grammatically <grin>
Iride01 is offline  
Old 03-11-22, 05:19 PM
  #15  
KJ43
Dead but dreaming
 
KJ43's Avatar
 
Join Date: Oct 2020
Location: Bay Area, CA (East Bay - Contra Costa County)
Posts: 407

Bikes: 2020 Santa Cruz Stigmata, 2022 Cannondale Synapse

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 157 Post(s)
Liked 318 Times in 178 Posts
Originally Posted by cxwrench
Some of the threads on this forum or maybe
I think those two emoji's pretty much encompass 99% of the threads on this forum.
KJ43 is offline  
Likes For KJ43:
Old 03-11-22, 09:37 PM
  #16  
alcjphil
Senior Member
 
alcjphil's Avatar
 
Join Date: Jun 2002
Location: Montreal, Quebec
Posts: 5,869
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1792 Post(s)
Liked 1,671 Times in 955 Posts
Originally Posted by cxwrench
Some of the threads on this forum or maybe
I think that many of the threads in this forum offer solutions to problems that many others never experience
alcjphil is offline  
Old 03-11-22, 09:53 PM
  #17  
Rolla
Guest
 
Join Date: Sep 2020
Posts: 2,888
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1346 Post(s)
Liked 3,269 Times in 1,439 Posts
So Googling the bike in the OP's sig, I get this:




Are we talking about threaded metal schraeder valves and nuts? Say it ain't so!


Last edited by Rolla; 03-11-22 at 09:58 PM.
Rolla is offline  
Likes For Rolla:
Old 03-11-22, 09:55 PM
  #18  
dedhed
SE Wis
 
dedhed's Avatar
 
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,516

Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970

Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2731 Post(s)
Liked 3,361 Times in 2,034 Posts
You don't "need" the nut. Some tubes the stem isn't even threaded.

dedhed is offline  
Likes For dedhed:
Old 03-11-22, 10:10 PM
  #19  
Kedosto
Callipygian Connoisseur
 
Join Date: Nov 2008
Posts: 1,373
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 564 Post(s)
Liked 350 Times in 190 Posts
Originally Posted by Rolla
So Googling the bike in the OP's sig, I get this:




Are we talking about threaded metal schraeder valves and nuts? Say it ain't so!

The first time I saw one I was taken aback.

But… I’m still shaking my head over the notion of using blue Loctite on the valve stem nut. I’m shaking the other side of my head over the notion of intentionally not using the nut when it’s so helpful. Whatever.
Kedosto is offline  
Likes For Kedosto:
Old 03-12-22, 06:20 AM
  #20  
Kapusta
Advanced Slacker
 
Kapusta's Avatar
 
Join Date: Feb 2017
Posts: 6,188

Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt

Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2749 Post(s)
Liked 2,516 Times in 1,422 Posts
I always use the nut and won’t buy tubes that are not threaded to take one.

I find on larger tires if the pressure is low, the stem just pushes into the rim when I try to push the pump head on but unless less it is really low I can’t push against the tire enough to brace the stem, so I have to deflate the tire to be able to do so.

Last edited by Kapusta; 03-12-22 at 02:35 PM.
Kapusta is offline  
Likes For Kapusta:
Old 03-12-22, 06:27 AM
  #21  
southpier
Senior Member
 
Join Date: Aug 2011
Posts: 552
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 197 Post(s)
Liked 51 Times in 41 Posts
what time does walmart open? asking for a friend
southpier is offline  
Old 03-12-22, 07:15 AM
  #22  
freeranger
Senior Member
 
freeranger's Avatar
 
Join Date: Jun 2005
Location: Kentucky
Posts: 2,579

Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike

Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 421 Post(s)
Liked 691 Times in 431 Posts
If you want to leave the nut on a presta valve stem, but don't want to tighten it down against the rim, you could always buy a small round rubber o-ring at the hardware store and put it just above the nut.
freeranger is offline  
Old 03-12-22, 08:01 AM
  #23  
rumrunn6
Senior Member
 
rumrunn6's Avatar
 
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,529

Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0

Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5220 Post(s)
Liked 3,565 Times in 2,332 Posts
a cpl of my Schrader tubes have threads & the screw on collar. out of curiosity I used one, one time. it kept coming loose. thought maybe because I drill out the Presta holes, so there wasn't much surface tension at the rim to keep it in place. about 1 second more thought than it deserved. so I chucked it


rumrunn6 is offline  
Old 03-12-22, 09:57 AM
  #24  
Jeff Neese
Senior Member
 
Join Date: Jul 2014
Posts: 1,486
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 1080 Post(s)
Liked 681 Times in 438 Posts
Originally Posted by Rolla
So Googling the bike in the OP's sig, I get this:




Are we talking about threaded metal schraeder valves and nuts? Say it ain't so!

I have one bike with schrader valves. I found that some Schwalbe schrader tubes have those lock nuts and now that's all I buy. That nut makes it SO much easier both to inflate the tires, and it keeps them straight in the rim. We've all seen wheels where the valve stem was off to an angle. Few things look more ghetto on a bicycle.

It's funny to me the people that say they don't use those nuts, even on their presta valves. There's no downside.

Jeff Neese is offline  
Old 03-12-22, 10:15 AM
  #25  
njkayaker
Senior Member
 
Join Date: Sep 2007
Location: Far beyond the pale horizon.
Posts: 14,241
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
Quoted: 4222 Post(s)
Liked 1,322 Times in 916 Posts
Originally Posted by Jeff Neese
I have one bike with schrader valves. I found that some Schwalbe schrader tubes have those lock nuts and now that's all I buy. That nut makes it SO much easier both to inflate the tires, and it keeps them straight in the rim. We've all seen wheels where the valve stem was off to an angle. Few things look more ghetto on a bicycle.
You don't need the little nut to install tubes properly.
njkayaker is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.