Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Capable chain repair tool? Does one exist that can be carried on the bike?

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Capable chain repair tool? Does one exist that can be carried on the bike?

Old 05-18-19, 07:51 PM
  #1  
KC8QVO
Senior Member
Thread Starter
 
Join Date: Apr 2013
Posts: 948

Bikes: Surly Disk Trucker, 2014 w/Brooks Flyer Special saddle, Tubus racks - Duo front/Logo Evo rear, 2019 Dahon Mariner D8, Both bikes share Ortlieb Packer Plus series panniers, Garmin Edge 1000

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 299 Post(s)
Liked 76 Times in 67 Posts
Capable chain repair tool? Does one exist that can be carried on the bike?

If I had to repair a chain at home I'd use my hydraulic press. That isn't very portable.

I have a cheap screw type chain repair tool and tried to use it before - its pretty much worthless as the screw just bends and walks off.

Is there something out there that is good quality and durable enough to work well that I can carry on the bike?
KC8QVO is offline  
Old 05-18-19, 07:55 PM
  #2  
LeeG
Senior Member
 
Join Date: Sep 2008
Posts: 4,957
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Likes: 0
Liked 7 Times in 6 Posts
Try another screw type, they work fine.
LeeG is offline  
Old 05-18-19, 08:17 PM
  #3  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 15,169

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Raleigh Pro, Trek Cycle Cross, Mongoose tomac ATB, GT Bravado ATB, JCP Folder

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3011 Post(s)
Liked 1,335 Times in 934 Posts
I would suggest a quality chain tool like a Park CT-5. Very common and likely the most common replacement pin if one should break. But I'll add a tip. Once the chain is positioned in the too, the pin is screwed onto the chain's rivet and it mbegins to move slightly. Then back off the tool's pin and restart the screwing in. What this does is let the tool's pin better center on the chain's rivet before plunging into the chain's holes. If the tool's pin hangs up on the edge of the hole two things can happen. One is that the chain plate's hole can be punched larger then wanted. The other is the tool's pin can bend. Once bent it is vastly harder to line up with the next rivet and bend further. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 05-18-19, 08:38 PM
  #4  
BCDrums
Recreational Road Cyclist
 
BCDrums's Avatar
 
Join Date: Sep 2013
Location: MetroWest, Mass.
Posts: 360

Bikes: 1990 Peter Mooney road bike

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 164 Post(s)
Liked 90 Times in 59 Posts
Originally Posted by KC8QVO View Post
Is there something out there that is good quality and durable enough to work well that I can carry on the bike?
I took a chain tool on a cross-country ride and never used it. What are you doing that you need to carry such a tool? “Durable” implies that you expect to use it a lot.
BCDrums is offline  
Old 05-18-19, 08:47 PM
  #5  
woodcraft
Senior Member
 
woodcraft's Avatar
 
Join Date: Apr 2012
Location: Nor Cal
Posts: 5,833
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1734 Post(s)
Likes: 0
Liked 802 Times in 496 Posts
Not featherweight at 75g, but this is robust, compact & inexpensive.

https://www.amazon.com/Pedros-Six-Pa...ustomerReviews
woodcraft is offline  
Old 05-18-19, 08:49 PM
  #6  
themp
Senior Member
 
Join Date: Aug 2015
Posts: 235

Bikes: Specialized Crosstrail

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 79 Post(s)
Liked 30 Times in 22 Posts
Originally Posted by BCDrums View Post
I took a chain tool on a cross-country ride and never used it. What are you doing that you need to carry such a tool? “Durable” implies that you expect to use it a lot.
I carry this:

https://www.parktool.com/product/min...hain-tool-ct-5

and have on multiple occasions helped someone who has a broken chain on our heavily used MUP/Greenway. It has always been a broken quick link that is now missing, so I usually break the chain for a pin and put it back together one link short. It gets them home. I also carry different speed quick links, but usually the person just wants the chain shortened and do not want to take my quick link as a fix.
themp is offline  
Old 05-18-19, 08:59 PM
  #7  
Canker
Senior Member
 
Join Date: Aug 2005
Posts: 1,503
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 243 Post(s)
Liked 95 Times in 56 Posts
Are you trying to reuse a pin because that is a huge PITA and not a good idea. Pick up some quick links and carry those then you only need the chain tool to break the chain. Even pretty crappy chain tool can break a chain.
Canker is offline  
Old 05-18-19, 09:28 PM
  #8  
wipekitty
vespertine member
 
wipekitty's Avatar
 
Join Date: Jul 2013
Location: nowhere, USA
Posts: 2,476

Bikes: Yes

Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 686 Post(s)
Liked 215 Times in 163 Posts
Another vote for Park Tool CT-5.

I managed to mess one up pretty badly, but it took me a decade to do so, and I'm very good at breaking things.
wipekitty is offline  
Old 05-18-19, 09:47 PM
  #9  
SylvainG
Senior Member
 
Join Date: Apr 2017
Location: Ottawa,ON,Canada
Posts: 1,270

Bikes: Schwinn Miranda 1990, Giant TCX 2 2012

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 486 Post(s)
Liked 10 Times in 7 Posts
I have this multitool (different but with the same chain repair) and tried in on a piece of chain I have. Bit harder on the thumb but this work to extract and reattach a new pin.

SylvainG is offline  
Likes For SylvainG:
Old 05-18-19, 09:57 PM
  #10  
reburns
Senior Member
 
Join Date: Apr 2012
Location: Saratoga, CA
Posts: 365

Bikes: 2005 Trek T2000; 2005 Co-motion Speedster Co-pilot; various non-tandem road and mountain bikes

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 89 Post(s)
Liked 34 Times in 22 Posts
https://www.prestacycle.com/product/...ain-accessory/

combined with the Presta ratchet and bits that I now carry instead of a combo multi tool, this really works great
reburns is offline  
Likes For reburns:
Old 05-18-19, 10:28 PM
  #11  
Loose Chain
Senior Member
 
Loose Chain's Avatar
 
Join Date: Sep 2009
Location: USA
Posts: 2,067

Bikes: 84 Pinarello Trevisio, 86 Guerciotti SLX, 96 Specialized Stumpjumper, 2010 Surly Cross Check, 88 Centurion Prestige, 73 Raleigh Sports, GT Force, Bridgestone MB4

Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 278 Post(s)
Liked 69 Times in 54 Posts
I have owned many chain tools, never really had a problem with any of them. If the push pin is bent, get a new tool.
Loose Chain is offline  
Old 05-18-19, 10:30 PM
  #12  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 12,769

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1369 Post(s)
Liked 597 Times in 446 Posts
Originally Posted by Andrew R Stewart View Post
I would suggest a quality chain tool like a Park CT-5. Very common and likely the most common replacement pin if one should break. But I'll add a tip. Once the chain is positioned in the too, the pin is screwed onto the chain's rivet and it mbegins to move slightly. Then back off the tool's pin and restart the screwing in. What this does is let the tool's pin better center on the chain's rivet before plunging into the chain's holes. If the tool's pin hangs up on the edge of the hole two things can happen. One is that the chain plate's hole can be punched larger then wanted. The other is the tool's pin can bend. Once bent it is vastly harder to line up with the next rivet and bend further. Andy
+1
You may have to do this 2-3 times before you get a good, straight push.
I'd use a Quicklink for repair. Too many chains that are not supposed to be rejoined with the pin.
Bill Kapaun is offline  
Likes For Bill Kapaun:
Old 05-18-19, 11:03 PM
  #13  
jideta
Senior Member
 
Join Date: Apr 2019
Location: Honolulu
Posts: 262
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 94 Post(s)
Liked 138 Times in 74 Posts
Park I Beam and KMC Missing Link.
Never leave home without them.
jideta is offline  
Old 05-19-19, 01:38 AM
  #14  
krecik
Senior Member
 
Join Date: Jun 2018
Posts: 358
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 137 Post(s)
Liked 85 Times in 54 Posts
​​​​​​​

Last edited by krecik; 01-13-21 at 01:55 PM.
krecik is offline  
Old 05-19-19, 05:59 AM
  #15  
shelbyfv 
Senior Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 9,157
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 2575 Post(s)
Liked 2,837 Times in 1,513 Posts
I've found even the ones included in multi tools (as above) adequate for on the road repairs. Generally you are just pushing out one pin to remove the broken link. Quick link for the repair. Technique and patience are key.
shelbyfv is offline  
Old 05-19-19, 06:07 AM
  #16  
dedhed
SE Wis
 
dedhed's Avatar
 
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 7,915

Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970

Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1704 Post(s)
Liked 1,347 Times in 870 Posts
Hydraulic press for a chain seems like a bit of overkill to me. At least what I consider a hydraulic press.
https://www.northerntool.com/shop/to...1793_200641793
dedhed is online now  
Old 05-19-19, 06:10 AM
  #17  
dsbrantjr
Senior Member
 
dsbrantjr's Avatar
 
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,152

Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta

Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 1371 Post(s)
Liked 905 Times in 630 Posts
Another vote for the CT-5.
dsbrantjr is offline  
Old 05-19-19, 07:20 AM
  #18  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 32,903

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 1686 Post(s)
Likes: 0
Liked 564 Times in 417 Posts
Originally Posted by krecik View Post
Chain breakers aren't really made to split a chain with no help from the user. A chain pin has been squashed (mushroomed) at the edges, that's what keeps it in the link. When I split a chain at home, I file the head with a file or a dremel before using the tool, that way, it will last for years.
This is overkill. There is no need to file or Dremel the pin before removal. A decent chain tool will easily remove a riveted pin from any chain if used properly (i.e. aligned over the pin). I have a Park CT-3 that has cut dozens and dozens of chains to length over 25+ years and has never needed a new pin. I carry a very small chain tool on my bike but have only used it once and that was to help another rider who's chain was improperly installed initially.

Carry a quick link for when you really need a road-side chain repair.
HillRider is offline  
Old 05-19-19, 07:56 AM
  #19  
JohnDThompson 
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 22,838

Bikes: Several, mostly not name brands.

Mentioned: 134 Post(s)
Tagged: 0 Thread(s)
Quoted: 2684 Post(s)
Liked 1,395 Times in 866 Posts
Originally Posted by dedhed View Post
Hydraulic press for a chain seems like a bit of overkill to me.
That was my thought as well. We assembled hundreds of chains daily at Trek, using chain pliers:



But pliers aren't very portable. I carry a "chain pup" with me on rides (I've had it for years and haven't had to use it yet):

JohnDThompson is offline  
Old 05-19-19, 08:00 AM
  #20  
krecik
Senior Member
 
Join Date: Jun 2018
Posts: 358
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 137 Post(s)
Liked 85 Times in 54 Posts
​​​​​​​

Last edited by krecik; 01-13-21 at 01:58 PM.
krecik is offline  
Old 05-19-19, 08:22 AM
  #21  
fietsbob
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,599

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,321 Times in 831 Posts
Modern bushing-less flush rivet head derailleur chains are never lengthened,
only shortened and joined with a quick link.

to effect repairs you bring a section of the same chain and more quick links...

So for pressing out the rivet pin, the chain tool can be simple , though it needs to be reliable..


gave a trusty, but not the lightest one, to a friend , he found a lighter, more aluminum one , brought it instead ..

and somewhere in the southern Argentine Andes foothills he had to find a nail and use a rock ,

when the lighter chain tool broke..








.....
fietsbob is offline  
Likes For fietsbob:
Old 05-19-19, 08:42 AM
  #22  
HillRider
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 32,903

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 1686 Post(s)
Likes: 0
Liked 564 Times in 417 Posts
Originally Posted by JohnDThompson View Post
But pliers aren't very portable. I carry a "chain pup" with me on rides (I've had it for years and haven't had to use it yet):

Yeah, I have a couple of those and have them on my daily ride bikes. I used it one time to repair another rider's chain and it worked but it certainly isn't a "shop quality" tool. I haven't seen them for sale in years and wonder if they are still being made.
HillRider is offline  
Old 05-19-19, 09:43 AM
  #23  
krecik
Senior Member
 
Join Date: Jun 2018
Posts: 358
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 137 Post(s)
Liked 85 Times in 54 Posts
​​​​​​​

Last edited by krecik; 01-13-21 at 02:10 PM.
krecik is offline  
Old 05-19-19, 10:14 AM
  #24  
shelbyfv 
Senior Member
 
shelbyfv's Avatar
 
Join Date: Jun 2007
Location: TN
Posts: 9,157
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 2575 Post(s)
Liked 2,837 Times in 1,513 Posts
Originally Posted by krecik View Post
I suggest that you carry a spare chain with you already cut to the correct length with you on your rides as well as a master link to connect it.
shelbyfv is offline  
Old 05-19-19, 11:09 AM
  #25  
Bill Kapaun
Really Old Senior Member
 
Bill Kapaun's Avatar
 
Join Date: Feb 2007
Location: Mid Willamette Valley, Orygun
Posts: 12,769

Bikes: 87 RockHopper,2008 Specialized Globe. Both upgraded to 9 speeds.

Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 1369 Post(s)
Liked 597 Times in 446 Posts
Originally Posted by krecik View Post
I suggest that you carry a spare chain with you already cut to the correct length on your rides as well as a master link to connect it............
The OP wanted a LIGHT WEIGHT TOOL to carry.
Not a heavy chain.
Bill Kapaun is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.