Which Velocal type do I need?
#1
Full Member
Thread Starter
Join Date: Aug 2019
Location: Albuquerque
Posts: 227
Bikes: 1st Track bike: 1978 Speedwell titanium 1st Road bike: 2001 Independent Fabrication Crown Jewel
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 116 Times
in
65 Posts
Which Velocal type do I need?
Once again bikeforums has been super helpful but this time with disappointing news that Velocals will be no longer be producing bike decals. Good to know so we can get our orders in.
But which type do you guys recommend? I was going to order the standard 2 mil type but they have UV laminates in either high gloss, low gloss and matt. The one I need is for Columbus Spirit tubing which promptly disintegrated on a NOS frame. They claim that the UV treatment will make the decal last twice as long.
But which type do you guys recommend? I was going to order the standard 2 mil type but they have UV laminates in either high gloss, low gloss and matt. The one I need is for Columbus Spirit tubing which promptly disintegrated on a NOS frame. They claim that the UV treatment will make the decal last twice as long.
Last edited by Biketiger; 11-30-22 at 10:00 PM.
#2
Senior Member
Join Date: Jul 2022
Location: Pac NW
Posts: 1,921
Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 1,798 Times
in
653 Posts
It comes down to your intentions. The uncovered ones are for full restoration assuming you are going to clear coat on top of your decals.
frankly, I love the look of patina, new decals and a clear coat to stop any further rust.
frankly, I love the look of patina, new decals and a clear coat to stop any further rust.
__________________
"Leave the gun. Take the Colnagos."
"Leave the gun. Take the Colnagos."
Last edited by Robvolz; 12-01-22 at 09:39 AM.
#3
Full Member
Thread Starter
Join Date: Aug 2019
Location: Albuquerque
Posts: 227
Bikes: 1st Track bike: 1978 Speedwell titanium 1st Road bike: 2001 Independent Fabrication Crown Jewel
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 116 Times
in
65 Posts
Good question. I plan to remove the remains of the existing decal and place a new one in its place. It will not be under a clear coat.
Should I therefore splurge on the UV coating?
Should I therefore splurge on the UV coating?
#4
Senior Member
Join Date: Mar 2012
Location: Niagara Region, Canada
Posts: 1,450
Bikes: 1970s Alex Singer, 1960s Peugeot PX 10, 1960s Bertin C37, 1973 Carre Bertin C 37, 1972 Carlton Kermesse, 1981 Peugeot PX 14 Super Competition
Mentioned: 65 Post(s)
Tagged: 0 Thread(s)
Quoted: 344 Post(s)
Liked 266 Times
in
157 Posts
Biketiger-
Yes, since there will be no clear coat, get the UV resistant ones.
Yes, since there will be no clear coat, get the UV resistant ones.
#5
Full Member
Thread Starter
Join Date: Aug 2019
Location: Albuquerque
Posts: 227
Bikes: 1st Track bike: 1978 Speedwell titanium 1st Road bike: 2001 Independent Fabrication Crown Jewel
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 116 Times
in
65 Posts
Got it - thanks for the advice!
#6
Junior Member
I recommend the 1 mil (which I haven't used) or the 0.5 mil. I used 2 mil on a Centurion-Cinelli refurbishment and the 2 mil decals looked like blocks of plastic glued to the frame. Never again!
Note the edges of the 2 mil decals. The only decals (in my opinion) which look factory correct are the 0.5 mil waterslide decals.
Note the edges of the 2 mil decals. The only decals (in my opinion) which look factory correct are the 0.5 mil waterslide decals.
#7
Master Parts Rearranger
Join Date: Mar 2015
Location: Portlandia's Kuiper Belt, OR
Posts: 4,402
Bikes: 1982 Trek 720 - 1985 Trek 620 - 1984 Trek 620 - 1980 Trek 510 - Other luminaries past and present
Mentioned: 221 Post(s)
Tagged: 0 Thread(s)
Quoted: 1556 Post(s)
Liked 2,023 Times
in
989 Posts
I've done the 2 mil adhesive decals a lot with them. Just did the 1 mil for my latest bike. There is still an edge, but either thickness applies well. For either, I'd go with a glossy finish as it matches the glossy paint of most lugged bikes unless you want the matte look. Waterslide would be good, especially for running clear coat over. I am ignorant as to a waterslide's durability without a clear coat, so feel free to educate me on that given your experience (those of you who have done so)
#8
Full Member
Thread Starter
Join Date: Aug 2019
Location: Albuquerque
Posts: 227
Bikes: 1st Track bike: 1978 Speedwell titanium 1st Road bike: 2001 Independent Fabrication Crown Jewel
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 116 Times
in
65 Posts
In my case, the Columbus Spirit is a large decal at the bottom of the seat tube so I am not too concerned about the edges as much as longevity. Since Velocals claims the laminated ones last twice as long and I will be applying over a clear coat that's what I'll do.
#9
Full Member
Join Date: Sep 2017
Location: Oklahoma City
Posts: 243
Bikes: 1985 Roberts SLX, Mercian 531, 1984 Torpado SLX,1981/82 Peugeot PSV-10, 1978 Charlie Roberts full touring, 1970 Charlie Roberts 531 road.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 79 Post(s)
Liked 164 Times
in
61 Posts
I recommend the 1 mil (which I haven't used) or the 0.5 mil. I used 2 mil on a Centurion-Cinelli refurbishment and the 2 mil decals looked like blocks of plastic glued to the frame. Never again!
Note the edges of the 2 mil decals. The only decals (in my opinion) which look factory correct are the 0.5 mil waterslide decals.
Note the edges of the 2 mil decals. The only decals (in my opinion) which look factory correct are the 0.5 mil waterslide decals.
#10
Junior Member
I'm not a bike painter, nor am I significantly inclined to do a lot of touch up painting on an old frameset with lots of wear and tear. I don't hesitate to get a bike repainted if I'm going to ride it any significant amount.
That said, my opinion about decals is:
For a bike which will not get repainted, I'd use the 1.0 mil decals. For a bike which will be repainted, I'd trust the painter (do your investigative homework) but I'd prefer the 0.5 mil decals be used along with several clear coats and sanding of the clear coat over the decals to level things out overall.
BTW: A thicker decal = more clear coats to camouflage the decal = more hand work = more expensive.
And, here's the 2001 Joe Bell interview with Rivendell. It's well worth the read: https://joebell.net/JB-interview-RR.html
That said, my opinion about decals is:
For a bike which will not get repainted, I'd use the 1.0 mil decals. For a bike which will be repainted, I'd trust the painter (do your investigative homework) but I'd prefer the 0.5 mil decals be used along with several clear coats and sanding of the clear coat over the decals to level things out overall.
BTW: A thicker decal = more clear coats to camouflage the decal = more hand work = more expensive.
And, here's the 2001 Joe Bell interview with Rivendell. It's well worth the read: https://joebell.net/JB-interview-RR.html