Corrosion under rim tape
#1
Junior Member
Thread Starter
Corrosion under rim tape
I was just taking apart a front wheel to rebuild with a hub dynamo, and found what looks like powdery white corrosion around one of the spoke holes:
Rim with corrosion around spoke hole
How concerned should I be?
To fill in the details, this is a wheel I built in 2017 for a drop bar conversion on an old MTB. (Alex Adventurer2 rim, Shimano Deore hub, Sapim Race spokes, Stan's tubeless rim tape). The clearance on the old frame with Rat Trap Pass tires was a little tight for comfort, so I returned it to original condition and removed the wheels after a couple of hundred miles. Since then, they hung in the shed (out of the weather but not climate controlled) until I brought them out of retirement for a Long Haul Trucker frame I picked up in early/mid 2020. They haven't been ridden in the rain, and currently have about 650 miles.
Is this apparent corrosion reason for concern? Is there anything I should do to prevent further corrosion?
Rim with corrosion around spoke hole
How concerned should I be?
To fill in the details, this is a wheel I built in 2017 for a drop bar conversion on an old MTB. (Alex Adventurer2 rim, Shimano Deore hub, Sapim Race spokes, Stan's tubeless rim tape). The clearance on the old frame with Rat Trap Pass tires was a little tight for comfort, so I returned it to original condition and removed the wheels after a couple of hundred miles. Since then, they hung in the shed (out of the weather but not climate controlled) until I brought them out of retirement for a Long Haul Trucker frame I picked up in early/mid 2020. They haven't been ridden in the rain, and currently have about 650 miles.
Is this apparent corrosion reason for concern? Is there anything I should do to prevent further corrosion?
#2
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,956
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 879 Times
in
526 Posts
If you had a significant problem, I'd suspect to see evidence of corrosion on the outside as well. And with multiple spoke holes, not just one. I'm not sure what your picture shows but I wouldn't be much concerned about it.
#3
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,953
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6178 Post(s)
Liked 4,795 Times
in
3,307 Posts
Corrosion? Where?
If it's there it's not bad enough to be anything. Just clean it up, put it all back together and ride.
You wouldn't believe the rusty steel rims many of us use to ride.
If it's there it's not bad enough to be anything. Just clean it up, put it all back together and ride.
You wouldn't believe the rusty steel rims many of us use to ride.
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
Were these rims set up with tubeless tires? Maybe some of the sealer got under the rim tape and dried and that's what you are seeing.
#5
Junior Member
Thread Starter
I’m inclined to clean up and move on, but curious what might have caused it.
Nope, I’m still sticking with tubes.
Likes For cjenrick:
#8
Senior Member
Join Date: Mar 2012
Posts: 978
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 504 Post(s)
Likes: 0
Liked 637 Times
in
355 Posts
It could be aluminum oxide, but it's hard to tell from the picture. Remove it with your fingernail and see if the underlying metal is damaged in any way. If you see clean metal underneath then it's not corrosion. If the metal is pitted and thinned, then it is corrosion and should be watched to see how fast it grows.
#9
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,953
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6178 Post(s)
Liked 4,795 Times
in
3,307 Posts
Regardless, it's not enough to be the slightest issue. You might just redo your tape again in a year or so and check if it's a continuing thing or just a one time thing.
#10
Full Member
wheel builder might have used white lithium grease on nipples
and be aware of galvanic corrosion due to dis-similar metals, ie brass to aluminum, nickel to aluminum etc
but looks like steel inserts so maybe aluminum nipples to steel
and be aware of galvanic corrosion due to dis-similar metals, ie brass to aluminum, nickel to aluminum etc
but looks like steel inserts so maybe aluminum nipples to steel