Brake caliper reach "margin"
#1
Newbie
Thread Starter
Join Date: May 2022
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Brake caliper reach "margin"
Brake caliper reach margin
Hello everyone,I've recently replaced the front brake caliper on a bike with a vintage road frame and 700c wheels. The old caliper had a 46mm-58mm reach while the new one is 39mm-51mm. The pads on on the new caliper make perfect contact with the rim's brake surface if I put them all the way down (at 51mm), so everything works fine, but I don't have any extra "room" to move them further down and I don't know if this could become a problem in the future (e.g. when the pads wear?).Can I just keep using this caliper or should I try to return it and purchase something with more reach (so that I have some extra margin)?
If in the future I'll ever need to replace my front wheel, I'll pick either a 700c or a 27" one, so the caliper should keep working just fine.. Is there something else I should consider?
Sorry if the question sounds stupid, but this is a beater bike and I've already spent too much money on it, so I'd like to make the right choice to avoid wasting even more money in the future
EDIT:
I've added pictures in an album of my profile named "Caliper reach"
Last edited by Osdril; 05-23-22 at 09:03 AM. Reason: Add pictures
#2
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
If the pads align well with the brake track you are fine. Your new caliper is a "short reach" and the old one was "long reach". Long reach brakes are increasing hard to find so be glad the new one is able to align. There should be no future problems but you can obtain a little extra clearance by filing the bottom of the adjustment slot a mm or so.
#3
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,790
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3510 Post(s)
Liked 2,925 Times
in
1,774 Posts
The shoes on my rear caliper on my bike are at the bottom. I don't foresee this as being any kind of problem.
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
One can always slightly grind the pads' upper edges to a bevel to further avoid the tire. Andy
__________________
AndrewRStewart
AndrewRStewart
#5
Newbie
Thread Starter
Join Date: May 2022
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thank you everyone, unfortunately I cannot post pictures yet..
If there's not anything that I should worry about in the future I think I'll just keep it
If there's not anything that I should worry about in the future I think I'll just keep it
#6
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
If in the future I'll ever need to replace my front wheel, I'll pick either a 700c or a 27" one, so the caliper should keep working just fine.. Is there something else I should consider?
Not sure what I think about a 700C on the rear and a 27" on the front. I'd want same size wheels.
PS. You can put pics in the Gallery here on BF and just let us know they are there.
#7
Newbie
Thread Starter
Join Date: May 2022
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If you pick the 27" wheel & tire in the future, then make sure you have room. That's going use up at least 8 more millimeters (≈5/16") clearance to whatever the closest point of interference is. Might be even less room if your current tire size is under 32 mm width
Not sure what I think about a 700C on the rear and a 27" on the front. I'd want same size wheels.
PS. You can put pics in the Gallery here on BF and just let us know they are there.
Not sure what I think about a 700C on the rear and a 27" on the front. I'd want same size wheels.
PS. You can put pics in the Gallery here on BF and just let us know they are there.
#8
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
Voilà, your pics....
#9
Newbie
Thread Starter
Join Date: May 2022
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#10
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,790
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3510 Post(s)
Liked 2,925 Times
in
1,774 Posts
I've got dual-pivot brakes that look like yours, except mine are on the rear. Each shoe hits the rim squarely where it should. Even if my brake arms were longer, I would have set the shoes up exactly where they are now.
#11
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,511
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2746 Post(s)
Liked 3,390 Times
in
2,053 Posts
Or invest $$ in drop pads.
https://www.amazon.com/Aican-Aluminu...0788QX964?th=1
https://bdopcycling.com/product/bdop...rs-pair-black/
#13
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
If this was a saddle all the way forward or rearward on it's rails I might be uncomfortable too. But for the brake pads I have no issue with going all the way to the end of the slot. The pads don't move in the slot once you tighten the nut.
#14
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Given the OP is working on an older road frame that originally had long reach brakes, I expect the fork and rear stay tire clearances are pretty generous.
#15
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,985
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,808 Times
in
3,316 Posts
((630-622) / 2 ) + (32 - 28) = 8 mm.
Or am I still thinking wrong somewhere? Though I do agree that many road bikes I've had from back in that day were formerly 27" wheels and even then very generous with space. But it's not something I'd assume willy nilly for all when all I have to do is look.
Last edited by Iride01; 05-23-22 at 05:16 PM.