Cut and rethread spokes ?
#1
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Napa Valley, CA
Posts: 908
Bikes: Wife says I have too many :-)
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 327 Post(s)
Liked 250 Times
in
158 Posts
Cut and rethread spokes ?
I am going to build a wheel with hub and rim I have on hand. I have some spokes to use but they are too long. I need to cut them shorter and cut new threads. Is this difficult to do ? Would I be better off to just buy new spokes ?
#2
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,516
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4353 Post(s)
Liked 3,992 Times
in
2,664 Posts
Do you have a spoke cutting and threading machine? I would probably buy the correct length personally.
#3
Senior Member
Join Date: May 2010
Location: Bastrop Texas
Posts: 4,478
Bikes: Univega, Peu P6, Peu PR-10, Ted Williams, Peu UO-8, Peu UO-18 Mixte, Peu Dolomites
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 965 Post(s)
Liked 1,629 Times
in
1,045 Posts
This is so true, but it would appear that finding good spokes right now is kinda hard as opposed to just a few months ago. I would only go to the trouble of cutting and threading if I could not find the proper spoke lengths...
Edit: That's right. The last time I resized some spokes I did not re-thread. I just cut the length and used an old spoke nipple to dress up the end.
Edit: That's right. The last time I resized some spokes I did not re-thread. I just cut the length and used an old spoke nipple to dress up the end.
__________________
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
No matter where you're at... There you are... Δf:=f(1/2)-f(-1/2)
Last edited by zandoval; 08-06-21 at 10:17 AM.
#4
Senior Member
Join Date: Apr 2010
Location: Elevation 666m Edmonton Canada
Posts: 2,482
Bikes: 2013 Custom SA5w / Rohloff Tourster
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1237 Post(s)
Liked 321 Times
in
248 Posts
It just depends if there's a close place that does them. Also depends if they are used and what's available now. Postal has been going postal lately. LOL
I've done it several times. One set I redid was right at the top of the previous threads. That was a goof measurement.
These were also hard to get 2.3 heads.
I've bought uncut ones also. I also goofed the order and got black instead of silver. Tried to sand one off, took too long and it looked lousy anyway. LOL Still have those 49 + 1.
I've done it several times. One set I redid was right at the top of the previous threads. That was a goof measurement.
These were also hard to get 2.3 heads.
I've bought uncut ones also. I also goofed the order and got black instead of silver. Tried to sand one off, took too long and it looked lousy anyway. LOL Still have those 49 + 1.
Last edited by GamblerGORD53; 08-05-21 at 11:32 PM.
#5
Really Old Senior Member
Spoke threads are rolled, not cut.
Take your micrometer and measure across the threads and again on the unthreaded section.
Threaded part is a greater dia.
Take your micrometer and measure across the threads and again on the unthreaded section.
Threaded part is a greater dia.
#6
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
#7
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
The effort and time to cut a spoke is not insignificant. I needed a replacement spoke a few months ago for a project and the shop didn't have the exact length so cut one for me. I forget what they charged me, ( $5? $10?) but it was quite a bit more than a single manufactured spoke out of a box, but considering the time it took them I didn't think it was unreasonable at all.
Each spoke is going to take some time to measure accurately and cut and crank through the threader, so the extra cost for 32 or 36 of them might be a lot. I am 100% certain you could find a box of DT Champion spokes in the right length for a lot less than 32 custom cut ones.
Each spoke is going to take some time to measure accurately and cut and crank through the threader, so the extra cost for 32 or 36 of them might be a lot. I am 100% certain you could find a box of DT Champion spokes in the right length for a lot less than 32 custom cut ones.
#8
Banned.
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,061
Bikes: Homebuilt steel
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2193 Post(s)
Liked 425 Times
in
337 Posts
Most better bike shops will have the tools to rethread your spokes. I found a shop near me that did what you are asking and they charged me less than the cost of new spokes and did them the same day. I think the mechanic enjoyed it. More recently I was looking to buy the tools to do it myself but it's kind of expensive for a hobbyist to justify.
BTW, bikehubstore.com sells lots of spokes and the owner is a great guy that goes out of his way to please. Highly recommended.
BTW, bikehubstore.com sells lots of spokes and the owner is a great guy that goes out of his way to please. Highly recommended.
Likes For IPassGas:
#10
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
How much too long are they? Is doing an extra cross a possibility?
#11
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,903
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,931 Times
in
1,212 Posts
I know there are places with these tools out there, but to my knowledge none of them are local to me. YMMV.
Likes For pdlamb:
#12
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1958 Post(s)
Liked 2,932 Times
in
1,489 Posts
The Morizumi is a great machine, very easy to use. We had one years ago and ended up stocking spokes in 10mm increments then cutting to what we needed. Greatly reduced the number of spokes we stocked. It really isn't very time consuming.
Likes For cxwrench:
#13
Senior Member
Thread Starter
Join Date: Sep 2006
Location: Napa Valley, CA
Posts: 908
Bikes: Wife says I have too many :-)
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 327 Post(s)
Liked 250 Times
in
158 Posts
is too expensive for something I would seldom use. Thanks for the idea.
And thanks to all that responded. The BF is great. A storehouse of knowledge
#14
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
Another thought: if you're using a double-walled rim and the spokes are just a tiny bit too long, nipple washers could "eat" about 1/2mm of spoke length. Nipple washers are still pretty easy to come by, too.
#15
The dropped
Join Date: Oct 2018
Location: Columbus, OH
Posts: 2,144
Bikes: Pake C'Mute Touring/Commuter Build, 1989 Kona Cinder Cone, 1995 Trek 5200, 1973 Raleigh Super Course FG, 1960/61 Montgomery Ward Hawthorne "thrift" 3 speed, by Hercules (sold) : 1966 Schwinn Deluxe Racer (sold)
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1739 Post(s)
Liked 1,014 Times
in
696 Posts
Another $0.02:
Cutting and rolling new threads is feasible for PG or single butted spokes. You might not have enough of the lower section on DB and TB spokes to roll, depending on how much you need to cut. I'm fine with spokes up to 2mm too long or short (per a calculator) on double walled rims.
Cutting and rolling new threads is feasible for PG or single butted spokes. You might not have enough of the lower section on DB and TB spokes to roll, depending on how much you need to cut. I'm fine with spokes up to 2mm too long or short (per a calculator) on double walled rims.
#16
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
As @Bill Kapaun notes, spoke threads are rolled, not cut. Some bike shops have spoke threading equipment. Phil Wood's is nice, as it rolls the threads and cuts to length in a single operation. But it's expensive (couple thousand dollars, last time I checked). Cyclo and Hozan have more affordable ones (couple hundred dollars), but in my experience, they don't do as nice a job, and you need to cut the spokes to the desired length separately.
#17
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,551
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 582 Times
in
399 Posts
Yes, if you try to cut the threads they will end up undersized. https://www.portlandbolt.com/technic...threads-bolts/
That is why they're rolled in the first place.
#18
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,516
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4353 Post(s)
Liked 3,992 Times
in
2,664 Posts
Yep. Wheel Fanatyk is out of stock (Hozan Spoke Threading Tool - Wheel Fanatyk), and it cost about 100 fancy spokes. I don't know if anybody has one of the really fancy Morizumi machines for sale, maybe I'll get one after I get me a $500 bike pump.
I know there are places with these tools out there, but to my knowledge none of them are local to me. YMMV.
I know there are places with these tools out there, but to my knowledge none of them are local to me. YMMV.
#19
Sr Member on Sr bikes
You could go the other way and cut the spoke heads off and use Z-bend pliers to creat your desired spoke length.
See this link —> https://jimlangley.net/wrench/espoketool.html
I actually created a replacement spoke this way for one of my bikes about a year or so ago. I didn’t have the z-bend pliers…just did it in the bench vise…but it works. It’s still on the bike working just fine. I’ve seen pics of wheels built entirely with Z-bent spoke. It looks OK, uniform, and works well. And, at $20.00 the pliers are a lot cheaper than a spoke threading tool.
https://www.amazon.com/Hangar-9-HAN1.../dp/B0006OBMJI
Dan
See this link —> https://jimlangley.net/wrench/espoketool.html
I actually created a replacement spoke this way for one of my bikes about a year or so ago. I didn’t have the z-bend pliers…just did it in the bench vise…but it works. It’s still on the bike working just fine. I’ve seen pics of wheels built entirely with Z-bent spoke. It looks OK, uniform, and works well. And, at $20.00 the pliers are a lot cheaper than a spoke threading tool.
https://www.amazon.com/Hangar-9-HAN1.../dp/B0006OBMJI
Dan
Last edited by _ForceD_; 08-07-21 at 04:50 PM.
Likes For _ForceD_:
#20
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,117
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
Ask around at local shops to see who has a Phil Wood or Morizumi spoke machine. My Morizumi is capable of shortening and rethreading spokes by as little as 2mm and down to whatever length the butting will allow.
#21
Senior Member
Call around, if a shop has a Phil Wood or Morizumi machine an experienced mechanic can cut/roll spokes for a wheelset in 15 minutes. I wouldnt mind the job as a mechanic, a chance to use one of the nicet, more elegant tools in the shop.
#22
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,334
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times
in
108 Posts
As above, if you can find a local shop with a Phil Wood or similar spoke threader, it's really easy. Assuming it's already set up for the correct gauge spoke (it often is), then setup is 30 seconds and maybe 10 seconds/spoke.
On the other hand, if they have one of those cheap tiny 3 roller ones then it's a PITA. I've had shops, even on an empty day, go with the "We don't use it often, can't find it" excuse just to avoid using them (wasn't a great shop).
On the other hand, if they have one of those cheap tiny 3 roller ones then it's a PITA. I've had shops, even on an empty day, go with the "We don't use it often, can't find it" excuse just to avoid using them (wasn't a great shop).
#23
Senior Member
Join Date: Dec 2007
Location: San Jose, California
Posts: 3,504
Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Likes: 0
Liked 35 Times
in
30 Posts
If you're ever down here in the South Bay, you can have them cut and re-rolled by Bicycle Express and Wheels By Fleming.
If you had posted earlier, I could have done it for you when I had my machine with me up in Loch Lomond back in May.
=8-|
If you had posted earlier, I could have done it for you when I had my machine with me up in Loch Lomond back in May.
=8-|
__________________
5000+ wheels built since 1984...
Disclaimer:
1. I do not claim to be an expert in bicycle mechanics despite my experience.
2. I like anyone will comment in other areas.
3. I do not own the preexisting concepts of DISH and ERD.
4. I will provide information as I always have to others that I believe will help them protect themselves from unscrupulous mechanics.
5. My all time favorite book is:
Kahane, Howard. Logic and Contemporary Rhetoric: The Use of Reason in Everyday Life
5000+ wheels built since 1984...
Disclaimer:
1. I do not claim to be an expert in bicycle mechanics despite my experience.
2. I like anyone will comment in other areas.
3. I do not own the preexisting concepts of DISH and ERD.
4. I will provide information as I always have to others that I believe will help them protect themselves from unscrupulous mechanics.
5. My all time favorite book is:
Kahane, Howard. Logic and Contemporary Rhetoric: The Use of Reason in Everyday Life