V-brake Bosses
#1
Junior Member
Thread Starter
Join Date: Nov 2011
Posts: 9
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
V-brake Bosses
Hi. Does anyone have a list of values for location of V-brake or Canti bosses in relation to hub centre different wheel sizes, specifically for 26" (559) but others would be good to have. Thanks, Ian
#2
Senior Member
Join Date: Dec 2019
Posts: 955
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 321 Post(s)
Liked 263 Times
in
212 Posts
I don't know what the official size is but I measured it to be 253.5mm for 26", and used this on a frame. The brakes fit fine. But I would also be interested to have a proper chart.
Likes For guy153:
#3
Senior Member
Join Date: Jan 2013
Location: South Jersey
Posts: 2,266
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 714 Post(s)
Liked 800 Times
in
475 Posts
Page 89 in this document has the specifications you are looking for. It is the 2015-16 Shimano frame fit specifications https://drive.google.com/file/d/0B-G...DobICllealyI5A
Likes For iandusud:
#5
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,986
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1172 Post(s)
Liked 2,567 Times
in
1,072 Posts
Careful trusting a chart though. Confirm with the actual brakes you want to use. Most have a range of adjustment, so extreme precision isn't needed, but watch out for edge cases.
Depending some on dropout design, rear posts usually angle away from the axle center, where front posts can angle towards the axle if there's significant rake. "Soft tail" curved seatstays like on a Hetchins, or curved near the bottom to miss a disk brake, could make your posts point at some angle compared to normal (tangent to the rim).
Mark B
Depending some on dropout design, rear posts usually angle away from the axle center, where front posts can angle towards the axle if there's significant rake. "Soft tail" curved seatstays like on a Hetchins, or curved near the bottom to miss a disk brake, could make your posts point at some angle compared to normal (tangent to the rim).
Mark B
Likes For bulgie:
#6
Junior Member
Thread Starter
Join Date: Nov 2011
Posts: 9
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Hi Mark, Thank you. I have actually considered this and I'm sure that you're right that it will have some effect, although mainly on the angle at which the brake block is set as the distance from the pivot point to the brake block is relatively short compared to a calliper brake. Cheers, Ian
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,071
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4200 Post(s)
Liked 3,853 Times
in
2,303 Posts
I strongly suggest that one mocks up the canti brakes and rim, on paper if not with the actual parts. I've found that for the Shimano MT62 family of cantis work best with post to post centers of about 50+mm wider than the rim's outer width. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart: