Sram brake sleeve nut won't fit into frame's hole
#1
Jacko nose historian
Thread Starter
Join Date: Sep 2005
Location: Salt Lake City!
Posts: 671
Bikes: 2006 52cm Trek 2200, Specialized Rockhopper (gets infrequent use unfortunately)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sram brake sleeve nut won't fit into frame's hole
The frame here is a 2008 Opera Canova (same as Pinarello fp3 I think). The frame fixing nut, or sleeve nut, or whatever it's called is too wide to fit into the hole for mounting the rear brake. This seems strange since the hole in the fork has no problems. I'm using sram force brakes which come with a few nuts in various lengths, but they are all the same diameter and don't fit the hole.
What's the solution for this?
What's the solution for this?
#3
Senior Member
Sometimes the problem is just too much paint/clearcoat, right at the front of the hole. A round file or dremel sanding drum can fix it.
#4
Jacko nose historian
Thread Starter
Join Date: Sep 2005
Location: Salt Lake City!
Posts: 671
Bikes: 2006 52cm Trek 2200, Specialized Rockhopper (gets infrequent use unfortunately)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So the frame has clear coat on top of carbon (no paint). Your solution seems simple for sure. I'm just nervous about damaging the structural integrity. I've emailed both sram and pinarello to see what their responses are. I'd guess they'll say, "dremel at your own risk" and void any warranty since they have liability issues to worry about.
I'm curious how often you've drilled or dremeled out like that and how common it is. Ever had a problem with it. Etcetera.
Thx
I'm curious how often you've drilled or dremeled out like that and how common it is. Ever had a problem with it. Etcetera.
Thx
#5
Jacko nose historian
Thread Starter
Join Date: Sep 2005
Location: Salt Lake City!
Posts: 671
Bikes: 2006 52cm Trek 2200, Specialized Rockhopper (gets infrequent use unfortunately)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
still worried that it's possibly dangerous.
#6
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
A short 5/16" drill bit turned by gripping it sideways in a pair of pliers or Vise Grips can be used to ream out the hole to the proper diameter. You have to turn it a fraction of a rotation at a time but it will work and should only remove the paint or clearcoat that's clogging the hole. Do NOT drill from the rear of the frame, you only want to open up the side of the hole facing the seat tube.
#7
Senior Member
Join Date: Dec 2009
Location: Melbourne, Oz
Posts: 9,545
Bikes: https://weightweenies.starbike.com/forum/viewtopic.php?f=10&t=152015&p=1404231
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 1528 Post(s)
Liked 718 Times
in
510 Posts
+1 Hillrider. I'd try it by hand though.
There's no good reason why it shouldn't be the standard size; I bet it's just not finished properly.
There's no good reason why it shouldn't be the standard size; I bet it's just not finished properly.
#8
Jacko nose historian
Thread Starter
Join Date: Sep 2005
Location: Salt Lake City!
Posts: 671
Bikes: 2006 52cm Trek 2200, Specialized Rockhopper (gets infrequent use unfortunately)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
yup. That did it. Thanks everybody.