Fork Crown Width
01-24-22, 08:55 PM
#1
Banned.
Thread Starter
Join Date: Jun 2004
Location: Torrance, CA
Posts: 3,061
Bikes: Homebuilt steel
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 2193 Post(s)
Liked 425 Times
in
337 Posts
Fork Crown Width
Thinking about making a flat or semi-flat crown fork and noticed a variety of different crown widths. Some crowns rated on inside clearance and others center to center between the blades. Going for clearance of at least 28c road tires, if not a little bigger. Don't need fender clearance or anything like that. I don't want anything super wide either. Just medium sporty. Any guidance appreciated.
01-25-22, 07:09 AM
#2
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,396
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,696 Times
in
2,517 Posts
You're going to have to work pretty hard to find a crown that does not clear 28c tires. There were some vintage ones that would be tight.
01-25-22, 10:04 AM
#3
Team Beer
Join Date: Apr 2004
Location: Sacramento CA
Posts: 6,339
Bikes: Too Many
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 114 Post(s)
Liked 159 Times
in
104 Posts
The Allotec A17-1 is a flat crown and has a 42 mm inside width.
https://framebuildersupply.com/colle...m-inside-width
https://framebuildersupply.com/colle...m-inside-width
__________________
I'm not one for fawning over bicycles, but I do believe that our bikes communicate with us, and what this bike is saying is, "You're an idiot." BikeSnobNYC
I'm not one for fawning over bicycles, but I do believe that our bikes communicate with us, and what this bike is saying is, "You're an idiot." BikeSnobNYC
Likes For Cynikal:
01-25-22, 10:09 AM
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
Tom- I could measure the crowns I have if needed, most are mix of HJ, Richard Sachs and Pacenti. The HJ crowns are the narrowest IIRC and they cleat the 28 tires I've run, although not with much more clearance. What size steerer? Andy
__________________
AndrewRStewart
AndrewRStewart
01-25-22, 10:05 PM
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,073
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4201 Post(s)
Liked 3,857 Times
in
2,305 Posts
Tom- I pulled out the 1" crowns I have, it's a lot. Most are off topic for your needs. I measured the inside widths about where a tire's wide point might be. The HJ are about 42mm and this is about the narrowest I would suggest for a 28mm tire. The Pacenti Artisan runs about 47mm. Both for aprox 20x28 blades. If you end up wanting to use either of these (or other 1" crowns) let me know. Andy
__________________
AndrewRStewart
AndrewRStewart
