Need Ritchey crank end cap
#1
Full Member
Thread Starter
Join Date: Sep 2017
Location: Maryland
Posts: 368
Bikes: Diamondback Haanjo Trail, Fuji Team Road
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 160 Post(s)
Liked 68 Times
in
46 Posts
Need Ritchey crank end cap
The non-drive side of my Ritchey crank is missing the black end cap you see on the drive side. The cap is threaded and screws into my crank and has a hole in the middle for the crank bolt.
I haven't had luck on eBay or on the Ritchey website. Any idea where I can one? It's really just cosmetic, but I just want to complete the bike. (The bike isn't this dirty anymore)
I haven't had luck on eBay or on the Ritchey website. Any idea where I can one? It's really just cosmetic, but I just want to complete the bike. (The bike isn't this dirty anymore)
#2
Senior Member
Join Date: Oct 2005
Location: SW Ohio
Posts: 3,682
Bikes: Puch Marco Polo, Saint Tropez, Masi Gran Criterium
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1163 Post(s)
Liked 442 Times
in
315 Posts
https://www.ebay.com/itm/Mounting-Bo...-127632-2357-0
Like this?
i can’t tell if your Ritchey crank is square taper or Octalink or Isis. I’m assuming square taper?
Like this?
i can’t tell if your Ritchey crank is square taper or Octalink or Isis. I’m assuming square taper?
#3
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,509
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2746 Post(s)
Liked 3,390 Times
in
2,053 Posts
#5
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,509
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2746 Post(s)
Liked 3,390 Times
in
2,053 Posts
Likes For dedhed:
#6
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,551
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 582 Times
in
399 Posts
Split image. Top is original crank bolt and chainring hardware; bottom is the Ti replacement. Notice the original was not self-extracting.
#7
Full Member
Thread Starter
Join Date: Sep 2017
Location: Maryland
Posts: 368
Bikes: Diamondback Haanjo Trail, Fuji Team Road
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 160 Post(s)
Liked 68 Times
in
46 Posts
The first time I tried removing the cranks, I did leave the cap in place and thought better of it once the washer started bearing on the back side of the cap. I ended up using a puller and it required A LOT of torque.
Likes For pennpaul: