For the love of English 3 speeds...
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
Current state.
Rear view
Cuts a nice profile!
Decals revealed after removing Batman tape and metal head badge
Sturmey Archer AW. Stamped "62" "2"
Front rim.
Front and rear fenders. Decal almost entirely worn off rear.
Hi, again. I think I can post photos now that I've achieved ten posts! I had all of this written out prior to joining this forum, so bear with me if it's kinda long. I found this bike, or should I say it found me, at a local thrift store. I knew it seemed something unique, but didn't pull the trigger on buying it for the $40 they originally wanted for it, and it looked like a kid had previously owned it as it had Batman duct tape over the seat and down tubes, but after a week of it sitting there and no one wanting it we negotiated a $25 price and it was mine! When I saw it originally I had taken some pictures of and had tried doing some research online about what kind of bike this might be. I Googled the "Royal" head badge and could only find one photo by someone selling a crusty one on U.K. Ebay for four Pounds. I did find all sorts of similar logos though, but nothing else that matched. I determined, I think, it was probably something made by Raleigh or a subsidiary. Through Sheldon Brown's site I found out how to determine it's age via the Sturmey Archer gear hub. It was indeed stamped "62" "2" "AW". So, 1962! Heck, that's old! I should know as I was born in 1964. ;-) I found the stamped serial number under the seat and it reads "26269 N PH". For some reason Sheldon Brown's and other sites skip how to decode serial #s from 1962 and 1963. So, anyone's guess is as good as mine what it means. I think since there is a "2" "62" close to each other at the beginning and that's the same as what's on the gear hub, I'm going with 1962 as year of build. The "N" some would saw could be made in Nottingham. The decal on the rear fender is mostly rubbed off, and I read on another site that's where it might say Nottingham. No idea about the "PH", well I do have a theory. After I cleaned off the Batman tape one could see remnants of the decal on the seat post of what appears to say "Made in England for someone Harris something building in New York". Well, I did find one other mention online of another person having a bike from this year and his decal read, "Made in England For D.P. Harris HDW & MFG Rollfast Building New York". Yup, that's what this one appears so say too. Does the "PH" on the stamped serial# mean P Harris? Furthering this theory, the only mention of a "Royal" brand on Brown's site says there was a "Royal Scot" (closest to Royal on the list) brand that was made for a major bicycle dealer in New York. So, that's my best guess. The bike was made in England by Raleigh for D.P. Harris (founder of the famous Rollfast bikes) in 1962. So, then, how did it get to Denver, Colorado? Someone thought enough of the bike to replace some parts at some point to keep it going; an aluminum USA Sunrim on the rear, a vinyl Avocet seat, a Nitto aluminum handle bar neck , Cheng Shin tires a added a nifty 1980s Union Dynamo front and rear light set (made in West Germany - it works!). I'm guessing the brake and gear cable lines and tubes may have been replaced too. Otherwise, best I can tell is everything else is original and I'm happy to report the thing rides great! The tires and tubes even are holding air after pumping them up and the gears and brakes work fine. I haven't really had to do anything but some cleaning, and I'll do more in the near future, plus lubricating. I love the rusty,rough patina. Anyway, that's the story so far on my 1962 Royal English 3-speed. I know it's a "B" brand Raleigh and probably not worth very much money, but it has character and I love it! If anyone has any info or corrections, please feel free to chime in.
I notice that the trigger is on the wrong side.
Depending on your skill level, I would attend to the bottom bracket and headset bearings.
A short term temp fix is to pour some heavy oil (not too much) down the seat tube and let the
excess seep out the bottom.
I agree to leave the paint/patina alone other than a good cleaning.
Keep your eye open for a vintage leather saddle to top it off.
Senior Member
Good morning. I have a question... The 3 speed hub on my late 50's Hercules says "3 Speed Model NO14522 HUB" on it and I don't see any other markings on it. I cannot seem to find any information on it. Anyone hear of that hub model? The bike had a mix match of parts on it so it could have been from anything. Thanks!
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Cool bike and I like the price..
I notice that the trigger is on the wrong side.
Depending on your skill level, I would attend to the bottom bracket and headset bearings.
A short term temp fix is to pour some heavy oil (not too much) down the seat tube and let the
excess seep out the bottom.
I agree to leave the paint/patina alone other than a good cleaning.
Keep your eye open for a vintage leather saddle to top it off.
I notice that the trigger is on the wrong side.
Depending on your skill level, I would attend to the bottom bracket and headset bearings.
A short term temp fix is to pour some heavy oil (not too much) down the seat tube and let the
excess seep out the bottom.
I agree to leave the paint/patina alone other than a good cleaning.
Keep your eye open for a vintage leather saddle to top it off.
Regarding the trigger (I assume shifter? Sorry,I'm still learning the lingo) I tried moving it already and unfortunately due to the lack of slack in the cable and the curves of the handle bar it pretty much only fits there where it is. Otherwise, the cable fitting coming out of the shifter bends and/or the clamp won't fit well enough to tighten the bracket screws.
Yea, I love the battle-worn patina. I'd also love to know what it has gone through to have all the scrapes, bumps and bruises. Fortunately, here in Denver since it's so dry we have no trouble with things rusting so doubt any aging will get much worse as ling as it's not kept outside all the time.
Yes, I'll be keeping an eye out for a new seat for sure. I'm a thrift store junky so am always on the lookout for a deal! hehe
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Welcome to the English roadster club! You got a great deal there. Good detective work. Looks like someone who knew what they were doing turned this old bike into a real rider. The stem was changed to get a bit more reach and they lowered the overall gearing with what looks to be a 22T cog on the AW hub. New chain, cables, alloy rims and an inexpensive but useable seat. Not kid stuff. I'm not surprised it rides well.
Serial number. does the "2" "62" that matches the numbers on the hub mean 1962? "N" for Nottingham? "PH" for DP Harris?
As it was in the thrift store. It was tipped on it's side. it does look like a Gotham City bike with the Batman tape, eh?
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
Thank you! Is the purpose of pouring oil down the seat rube to oil the crank? If so it does has an oil port there. I'm reading here on this site that 20 weight motor oil is what I should use for this and in the Sturmey Archer gear hub? My car uses 5w20. Would that work?
Regarding the trigger (I assume shifter? Sorry,I'm still learning the lingo) I tried moving it already and unfortunately due to the lack of slack in the cable and the curves of the handle bar it pretty much only fits there where it is. Otherwise, the cable fitting coming out of the shifter bends and/or the clamp won't fit well enough to tighten the bracket screws.
Yea, I love the battle-worn patina. I'd also love to know what it has gone through to have all the scrapes, bumps and bruises. Fortunately, here in Denver since it's so dry we have no trouble with things rusting so doubt any aging will get much worse as ling as it's not kept outside all the time.
Yes, I'll be keeping an eye out for a new seat for sure. I'm a thrift store junky so am always on the lookout for a deal! hehe
Regarding the trigger (I assume shifter? Sorry,I'm still learning the lingo) I tried moving it already and unfortunately due to the lack of slack in the cable and the curves of the handle bar it pretty much only fits there where it is. Otherwise, the cable fitting coming out of the shifter bends and/or the clamp won't fit well enough to tighten the bracket screws.
Yea, I love the battle-worn patina. I'd also love to know what it has gone through to have all the scrapes, bumps and bruises. Fortunately, here in Denver since it's so dry we have no trouble with things rusting so doubt any aging will get much worse as ling as it's not kept outside all the time.
Yes, I'll be keeping an eye out for a new seat for sure. I'm a thrift store junky so am always on the lookout for a deal! hehe
I use a blue marine grease.
Most of us use the blue 3 in 1 oil in the hub, a few drops every couple of months seems to to the trick.
As far as the trigger,someone has replaced the cable with one that was too short.
New ones are readily available from most bike shops @ $8.00-10.00
You'll need to trim the housing to fit your set up.
Trigger is traditionally mounted flat (parallel to the ground) in front of the right caliper.
This is, of course, a personal preference..
Last edited by gster; 11-08-18 at 10:10 AM.
Newbie
Join Date: Nov 2018
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'm trying to post some images on the Raleigh bike but not sure its working. The stainless steel part at the center of the back wheel says Sturmy Archer and has the numbers 08 or 80 depending on which way you read it. At the bottom of the center of the bike (between the pedals) is the number 122822 if I'm reading it correctly. Still trying to find out if it is a 1969 bike.
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I'm trying to post some images on the Raleigh bike but not sure its working. The stainless steel part at the center of the back wheel says Sturmy Archer and has the numbers 08 or 80 depending on which way you read it. At the bottom of the center of the bike (between the pedals) is the number 122822 if I'm reading it correctly. Still trying to find out if it is a 1969 bike.
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Yes, to lubricate the BB bearings, I've got some heavy weight gear oil. But this is only a temporary solution until you get it apart and do a proper repack.
I use a blue marine grease.
Most of us use the blue 3 in 1 oil in the hub, a few drops every couple of months seems to to the trick.
As far as the trigger,someone has replaced the cable with one that was too short.
New ones are readily available from most bike shops @ $8.00-10.00
You'll need to trim the housing to fit your set up.
Trigger is traditionally mounted flat (parallel to the ground) in front of the right caliper.
This is, of course, a personal preference..
I use a blue marine grease.
Most of us use the blue 3 in 1 oil in the hub, a few drops every couple of months seems to to the trick.
As far as the trigger,someone has replaced the cable with one that was too short.
New ones are readily available from most bike shops @ $8.00-10.00
You'll need to trim the housing to fit your set up.
Trigger is traditionally mounted flat (parallel to the ground) in front of the right caliper.
This is, of course, a personal preference..
Senior Member
Does anyone know how to take a vintage cottered crank chain ring and use it with a cotter less 3 piece setup?
Membership Not Required
Join Date: Jan 2005
Location: On the road-USA
Posts: 16,855
Bikes: Giant Excursion, Raleigh Sports, Raleigh R.S.W. Compact, Motobecane? and about 20 more! OMG
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 70 Post(s)
Likes: 0
Liked 16 Times
in
15 Posts
Aaron
__________________
Webshots is bailing out, if you find any of my posts with corrupt picture files and want to see them corrected please let me know. :(
ISO: A late 1980's Giant Iguana MTB frameset (or complete bike) 23" Red with yellow graphics.
"Cycling should be a way of life, not a hobby.
RIDE, YOU FOOL, RIDE!"_Nicodemus
"Steel: nearly a thousand years of metallurgical development
Aluminum: barely a hundred
Which one would you rather have under your butt at 30mph?"_krazygluon
Webshots is bailing out, if you find any of my posts with corrupt picture files and want to see them corrected please let me know. :(
ISO: A late 1980's Giant Iguana MTB frameset (or complete bike) 23" Red with yellow graphics.
"Cycling should be a way of life, not a hobby.
RIDE, YOU FOOL, RIDE!"_Nicodemus
"Steel: nearly a thousand years of metallurgical development
Aluminum: barely a hundred
Which one would you rather have under your butt at 30mph?"_krazygluon
Senior Member
Thanks, BigChief! I forgot to post a photo of the serial number. Here it is as well as a pic of the bike as I found it in the thrift store complete with Batman tape! Like I said I can't find any reference to decode 1962 #s anywhere so far. And yeah, I'd love to know when and where someone did all that work to keep it road worthy. Thanks for the welcoming feedback everyone!
Serial number. does the "2" "62" that matches the numbers on the hub mean 1962? "N" for Nottingham? "PH" for DP Harris?
As it was in the thrift store. It was tipped on it's side. it does look like a Gotham City bike with the Batman tape, eh?
Serial number. does the "2" "62" that matches the numbers on the hub mean 1962? "N" for Nottingham? "PH" for DP Harris?
As it was in the thrift store. It was tipped on it's side. it does look like a Gotham City bike with the Batman tape, eh?
The rear wheel shows to have a CR18 sticker on it. The Sun CR18 rim is the best modern replacement rim for the 26 X 1-3/8 EA3 rims. Looks like it has stainless spokes as well. I think those rims are going for about $30, or so, these days and to build it with SS spokes-- probably $50 in parts (rim and spokes). So, that's a good thing right there -- the rear wheel with hub alone is worth the entry.
Senior Member
Join Date: Dec 2012
Location: St. Paul, MN
Posts: 1,604
Bikes: Too many 3-speeds, Jones Plus LWB
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 360 Post(s)
Liked 280 Times
in
126 Posts
Nervar used to make the Nervar Sport crankset, which was initially a steel cottered crank with alloy chainrings. Later versions were cotterless but still made of steel. There were also cottered alloy cranksets, but they are quite rare! Generally speaking, cottered cranks are easier to work with once you have a proper cotter press. They are less likely to creak and loosen up.
Senior Member
Join Date: Jan 2015
Posts: 3,240
Mentioned: 103 Post(s)
Tagged: 0 Thread(s)
Quoted: 1299 Post(s)
Likes: 0
Liked 104 Times
in
86 Posts
In any case, this 1950 Sports has locknuts so won't have damage from the left side mounting. I like this bike. One of the best CL ads I've seen in a long time.
Last edited by BigChief; 11-08-18 at 04:04 PM.
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Looks like a real good deal.
The rear wheel shows to have a CR18 sticker on it. The Sun CR18 rim is the best modern replacement rim for the 26 X 1-3/8 EA3 rims. Looks like it has stainless spokes as well. I think those rims are going for about $30, or so, these days and to build it with SS spokes-- probably $50 in parts (rim and spokes). So, that's a good thing right there -- the rear wheel with hub alone is worth the entry.
The rear wheel shows to have a CR18 sticker on it. The Sun CR18 rim is the best modern replacement rim for the 26 X 1-3/8 EA3 rims. Looks like it has stainless spokes as well. I think those rims are going for about $30, or so, these days and to build it with SS spokes-- probably $50 in parts (rim and spokes). So, that's a good thing right there -- the rear wheel with hub alone is worth the entry.
Senior Member
There really isn't any way to do that without some sort of machining.
Nervar used to make the Nervar Sport crankset, which was initially a steel cottered crank with alloy chainrings. Later versions were cotterless but still made of steel. There were also cottered alloy cranksets, but they are quite rare! Generally speaking, cottered cranks are easier to work with once you have a proper cotter press. They are less likely to creak and loosen up.
Nervar used to make the Nervar Sport crankset, which was initially a steel cottered crank with alloy chainrings. Later versions were cotterless but still made of steel. There were also cottered alloy cranksets, but they are quite rare! Generally speaking, cottered cranks are easier to work with once you have a proper cotter press. They are less likely to creak and loosen up.
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
Oh, real good to know! Thanks! I think that Nitto handle bar stem is going for $20-$30 on eBay too. A used Union Dynamo light set (1980s) is going for $25. (the lens on this one is cracked though). Based on these replaced parts: rim, spokes, handlebar neck and that Avocet O2 seat, does anyone have a guess as to when the work may have been done on this?
Royal Crown Lightweight, made for D.P. Harris...1956
$77.50 in 1956 would cost $510.00 today
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
More info
Apparently sold at Firestone stores...
https://thecabe.com/forum/threads/pa...crowns.110056/
Apparently sold at Firestone stores...
https://thecabe.com/forum/threads/pa...crowns.110056/
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
That is way cool! Not much different six years later, eh? Wonder if the '62 had the chain guard and was sold with those accessories. I got the impression when doing my research that once Raleigh bought many of the smaller companies out around 1960 some of the builds weren't as robust afterwards. Hence maybe why the '62 is just called "Royal". I need to steal that pic for my photo blog. hehe Thanks!
Last edited by Stenavpix; 11-08-18 at 07:41 PM.
Senior Member
Join Date: Jan 2015
Posts: 3,240
Mentioned: 103 Post(s)
Tagged: 0 Thread(s)
Quoted: 1299 Post(s)
Likes: 0
Liked 104 Times
in
86 Posts
That is way cool! Not much different six years later, eh? Wonder if the '62 had the chain guard and was sold with those accessories. I got the impression when doing my research that once Raleigh bought many of the smaller companies out around 1960 some of the builds weren't as robust afterwards. Hence maybe why the '62 is just called "Royal". I need to steal that pic for my photo blog. hehe Thanks!
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The bike in this ad looks American to me. The one piece crank and shark fin front mudguard stand out. Hard to say, but it looks like a welded frame too. Raleigh made so many custom label bikes that it's hard to keep track of them all. The OP's bike is typical of these from the early 60s. I have one too. A Royal Scot. There's a good chance the Royal looked very similar with white grips and cable housings. And this seat which is truly horrible to ride on. BTW, mine has a dealer sticker from "Wheel Goods" in Minneapolis
Senior Member
Join Date: Apr 2012
Location: Toronto
Posts: 2,572
Bikes: 1971 Hercules, 1978 Raleigh Superbe, 1978 Raleigh Tourist, 1964 Glider 3 Speed, 1967 Raleigh Sprite 5 Speed, 1968 Hercules AMF 3 Speed, 1972 Raleigh Superbe, 1976 Raleigh Superbe, 1957 Flying Pigeon, 1967 Dunelt 3 Speed
Mentioned: 57 Post(s)
Tagged: 0 Thread(s)
Quoted: 1030 Post(s)
Liked 445 Times
in
288 Posts
The bike in this ad looks American to me. The one piece crank and shark fin front mudguard stand out. Hard to say, but it looks like a welded frame too. Raleigh made so many custom label bikes that it's hard to keep track of them all. The OP's bike is typical of these from the early 60s. I have one too. A Royal Scot. There's a good chance the Royal looked very similar with white grips and cable housings. And this seat which is truly horrible to ride on. BTW, mine has a dealer sticker from "Wheel Goods" in Minneapolis
1964 AMF Hercules.
A very original bike so I've left the seat as is...
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,864
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2300 Post(s)
Liked 2,066 Times
in
1,260 Posts
Member
Join Date: Oct 2018
Location: Denver, CO
Posts: 33
Bikes: 1962 Royal 3 speed, 1986 Jetter 15 speed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I'm in Denver.
Last edited by Stenavpix; 11-09-18 at 08:59 AM.
Senior Member
Join Date: Jan 2015
Posts: 3,240
Mentioned: 103 Post(s)
Tagged: 0 Thread(s)
Quoted: 1299 Post(s)
Likes: 0
Liked 104 Times
in
86 Posts