Tap thread size
#1
WGB
Thread Starter
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
Tap thread size
I want to move from 4.5mm threads on my Ross Signature shifter bosses to 5mm so i have more choice of shifters. To do this do I need to get a specific size of 5mm tap or just ask for one for M4 5mm?? Just wanted to be sure because once they are tapped I can't go back....
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,093
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4208 Post(s)
Liked 3,875 Times
in
2,315 Posts
First- There is no M4 5mm. M4 is a 4mm OD.
Second- do check the boss's shape and it's compatibility with other shift levers.
Third- A bottoming tap will tap to nearly the base of a blind hole, which is what a boss has. Generally one uses a tapered tap then a plug tap and then the bottoming one.
Do be careful with the tap contacting the bottom of the hole. Tap breakage is very easy. Andy
Second- do check the boss's shape and it's compatibility with other shift levers.
Third- A bottoming tap will tap to nearly the base of a blind hole, which is what a boss has. Generally one uses a tapered tap then a plug tap and then the bottoming one.
Do be careful with the tap contacting the bottom of the hole. Tap breakage is very easy. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#3
Full Member
Join Date: Apr 2019
Location: Northern NJ
Posts: 419
Bikes: 1987 Pinarello Montello, 1996 Litespeed Classic, 1996 Colnago Master Light, 1997 Litespeed Ultimate, 2006 Opera Leonardo FP, 2006 Pinarello Paris FP, 1984 Pinarello Record, 89-ish Cornelo Profilo
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 119 Times
in
73 Posts
Does M4.5 have the same pitch as M5? If not, when you try to drill and tap M5 where the M4.5 hole is, you will probably end up with a mess - there's not enough difference that the drill will clean out the M4.5 threads completely. If they are both coarse thread they are both .5mm pitch.
#4
Blamester
How does the thread size effect the shifter?
No goin back if you tap it.
Keep it simple try a washer first.
No goin back if you tap it.
Keep it simple try a washer first.
#5
WGB
Thread Starter
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
Andy
I understand I will have to very carefully file tabs on the bosses to allow the replacement bases to fit.
Was going to drill a pilot hole first through bosses into frame (figure the base of each boss will cover those) and then wanted to tap the bolt holes to allow use of the slightly fatter bolts that rest of my shifter choices have. If I predrill the bosses the tap shouldn't bottom out.
Does this make sense??
I understand I will have to very carefully file tabs on the bosses to allow the replacement bases to fit.
Was going to drill a pilot hole first through bosses into frame (figure the base of each boss will cover those) and then wanted to tap the bolt holes to allow use of the slightly fatter bolts that rest of my shifter choices have. If I predrill the bosses the tap shouldn't bottom out.
Does this make sense??
#6
WGB
Thread Starter
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
Sorry the current shifter bolts are a slightly smaller diameter and thought they were 4.5mm but are they infact M4.5 bolts??
#7
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,984
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26424 Post(s)
Liked 10,380 Times
in
7,208 Posts
Anyway, I'd hate for you to come to grief over this. If all else fails, just buy and M4 and an M5 machine screw at the Home Depot and use them as gauges for what you have now.
#8
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Does M4.5 have the same pitch as M5? If not, when you try to drill and tap M5 where the M4.5 hole is, you will probably end up with a mess - there's not enough difference that the drill will clean out the M4.5 threads completely. If they are both coarse thread they are both .5mm pitch.
#9
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
#10
Full Member
Join Date: Apr 2019
Location: Northern NJ
Posts: 419
Bikes: 1987 Pinarello Montello, 1996 Litespeed Classic, 1996 Colnago Master Light, 1997 Litespeed Ultimate, 2006 Opera Leonardo FP, 2006 Pinarello Paris FP, 1984 Pinarello Record, 89-ish Cornelo Profilo
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 148 Post(s)
Liked 119 Times
in
73 Posts
Thanks. Yes, my bad. In M4.5, coarse is .75 I believe. I like to believe things on modern bikes are standardized well enough that I don't have to think too hard about metric threads.
#11
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,093
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4208 Post(s)
Liked 3,875 Times
in
2,315 Posts
I'd like to believe in world peace too but reality says otherwise. The bike business if full of mixed dimensional (metric and fractional) and designs meant to further the manufacture's profits and not the end user lives easier. Andy
__________________
AndrewRStewart
AndrewRStewart
#12
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,790
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3590 Post(s)
Liked 3,400 Times
in
1,934 Posts
Campagnolo type bosses are 5mm x 0.8mm thread; some Shimano bosses are 4.5mm x 0.75mm thread. I doubt you could retap a 4.75 x 0.75 boss to 5 x 0.8 without problems. Shimano did make a conversion kit to mount Campagnolo type levers ona Shimano "A-type" boss:
Source: Sutherland's 4th Edition
Source: Sutherland's 4th Edition
Likes For JohnDThompson:
#13
aka: Dr. Cannondale
Join Date: Jul 2009
Posts: 7,734
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2155 Post(s)
Liked 3,404 Times
in
1,205 Posts
Hmmmm.
I've actually had good luck tapping a 4.5mm bolt hole (old Shimano style) to 5mm X 8 using either a 'poor man's tap' - essentially a hardened 5mm bolt with a pair of vertical valleys Dremeled into it- or a 5mm bottoming tap so that it would accept a now-standard 5mm mounting bolt for a cable stop or downtube shifter.
Just be careful and take your time. No need to drill anything out, just re-tap the threads.
I've actually had good luck tapping a 4.5mm bolt hole (old Shimano style) to 5mm X 8 using either a 'poor man's tap' - essentially a hardened 5mm bolt with a pair of vertical valleys Dremeled into it- or a 5mm bottoming tap so that it would accept a now-standard 5mm mounting bolt for a cable stop or downtube shifter.
Just be careful and take your time. No need to drill anything out, just re-tap the threads.
__________________
Hard at work in the Secret Underground Laboratory...
Hard at work in the Secret Underground Laboratory...
#14
WGB
Thread Starter
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
@rccardr - I think it was your thread that got me thinking I could do this!
https://www.bikeforums.net/classic-v...ter-style.html
I was going to drill through into the down tube first with a very fine bit to prevent having the tap bottoming and breaking. I get that I have to stop after every 1/4 turn, reverse and clean the threads and that I must oil the tap.
Do I not still have to very carefully file tabs on the bosses to allow the replacement bases to fit?? Or, are you saying that just re-tapping the threads will be all I need?
I saw the mention of using the .5 inch hole saw and thought if I did this after drilling it my be neater and have a more flush fit to the frame
https://www.homedepot.com/p/Milwauke...0511/204994403
The Ross currently has the Shimano Z401 shifters and I wanted to switch to Exage Sport Shifters, if only because I have the same model levers, FD and RD on the bike already.
https://www.bikeforums.net/classic-v...ter-style.html
I was going to drill through into the down tube first with a very fine bit to prevent having the tap bottoming and breaking. I get that I have to stop after every 1/4 turn, reverse and clean the threads and that I must oil the tap.
Do I not still have to very carefully file tabs on the bosses to allow the replacement bases to fit?? Or, are you saying that just re-tapping the threads will be all I need?
I saw the mention of using the .5 inch hole saw and thought if I did this after drilling it my be neater and have a more flush fit to the frame
https://www.homedepot.com/p/Milwauke...0511/204994403
The Ross currently has the Shimano Z401 shifters and I wanted to switch to Exage Sport Shifters, if only because I have the same model levers, FD and RD on the bike already.
#15
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,116
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1789 Post(s)
Liked 1,629 Times
in
933 Posts
Why not keep the existing screws we all know work & swap the lever?
These are downtube shifters, correct? What am I missing?
These are downtube shifters, correct? What am I missing?
Last edited by base2; 06-16-19 at 09:44 PM.
#16
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,037
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 341 Times
in
251 Posts
Andy
I understand I will have to very carefully file tabs on the bosses to allow the replacement bases to fit.
Was going to drill a pilot hole first through bosses into frame (figure the base of each boss will cover those) and then wanted to tap the bolt holes to allow use of the slightly fatter bolts that rest of my shifter choices have. If I predrill the bosses the tap shouldn't bottom out.
Does this make sense??
I understand I will have to very carefully file tabs on the bosses to allow the replacement bases to fit.
Was going to drill a pilot hole first through bosses into frame (figure the base of each boss will cover those) and then wanted to tap the bolt holes to allow use of the slightly fatter bolts that rest of my shifter choices have. If I predrill the bosses the tap shouldn't bottom out.
Does this make sense??
Of course, you might be able to use the 4.5mm bolts with a small washer to hold the larger shifters. That would be ideal - no machining.
If that won't work what does the current setup look like? Pictures with the current bosses mounted and (if they're removeable) with them removed would be useful.
I am familiar with two scenarios. One is that there are bosses welded in place and you want to enlarge the thread from M4.5 (4.5mm od x 0.75mm per thread) to M5 (5mm od x 0.8mm per thread). If so, you don't need to drill holes in the frame. There exist things called bottoming taps. Ideally you use these in association with two other taps. The first one is more tapered and gets you started, but doesn't thread all the way down. The bottoming tap has almost no taper and taps almost to the bottom of the hole. There's a tap type that is midway between the two that you use in-between the taper tap and the bottoming tap.
If the current setup has a stud from one side to the other that holds the bosses, and the whole assembly comes off, then just enlarge the frame hole a bit and swap out a new set of bosses, which should be available for your frame size.
If you are planning on drilling into a modern, high strength frame and then tapping the frame, it won't work. Not anything I'd try, anyway. The alloy or steel is very strong and so is used in very thin wall sections so its too thin to hold threads. There are techniques (you drill a very small hole then indent a little nipple into the metal, and then thread the nipple). The pic below shows the ideal case of holes that are extruded and could be effectively tapped. Hard to do perfectly in a closed frame like a bike tube.
BTW, I can envision no scenario where I'd want to use a carbide grit hole so on anything remotely related to a a bicycle frame or part. That type of tool is for drilling very rough holes in ceramics. There are carbide-tipped hole saws that you might use on, say, work-hardened Reynolds 953 but that would be shop use in fabricating frames, not bike mode work. What was your intention? How are you proposing to use this?
Last edited by WizardOfBoz; 06-16-19 at 09:46 PM.
#17
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,790
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3590 Post(s)
Liked 3,400 Times
in
1,934 Posts
#18
Banned
More tools
Does M4.5 have the same pitch as M5? If not, when you try to drill and tap M5 where the M4.5 hole is, you will probably end up with a mess - there's not enough difference that the drill will clean out the M4.5 threads completely. If they are both coarse thread they are both .5mm pitch.
Measure.. there are thread pitch gages , which are part of most machinists tool boxes...
Metric pitch is thread per MM , so count how many per 10mm then divide by 10 .
#19
WGB
Thread Starter
Join Date: Jul 2017
Location: Niagara Region
Posts: 2,917
Bikes: Panasonic PT-4500
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1800 Post(s)
Liked 2,334 Times
in
1,378 Posts
I had this update fully typed then had a power failure!
Starting again.
First I'd like to apologize because I didn't post any pictures.
Here is the shifter boss for my Ross Signature. Current shifters are Shimano Z401. These take a Shimano only proprietary bolt (machine screw?? lever Screw??). I recently acquired a partial Exage Sport groupset which included the shifter set but no bolts. I reached for some spare bolts and no, standard M5 shifter bolts don't work because the Z401 bosses are threaded for a smaller bolt size. I believe that the current bosses are Shimano A type bosses and require bolts that are referred to variously as M4.5 x .75 or 4.5mm x .75. They are ones referred to by JohnDThompson above.
Z401 and Exage Sport shifters
Exage on top and 401 on bottom
The original bolts are a MM or so too short to fit through the Sport shifters and engage the threads of the boss and the Exage require a different boss cover than the Z401 have.
401 base on top and Exage on bottom
I spoke with a local frame builder who suggested that rather than search for longer M4.5 bolts I should just tap the threads to take the M5 x .80 bolts. I would have had him tap it there and then but I didn't have the frame with me. He walked me through the tap process and it seemed straight forward.
I approached a neighbor who has lots of taps and other nice tools but he didn't have any 5mm taps. The neighbor suggested that I insert a drill bit into the bolt hole in the boss and drill into the frame and he said that drilling would prevent the tap from bottoming out and breaking in the threads (at least I think that's what he meant). Judging from the response on here, I guess that pre-drilling before tapping is not needed.
The neighbor suggested a local store to get the tap. I began to wonder if there waa certain thread size that I needed and now realize the .80 part of the M5 x .80 will cover that question.
This brings me to the next part where my post was confusing
The replacement boss covers won't fit onto the bosses and so the bosses must be modified or trimmed to allow the mounting of the new bosses. In his post RCCARDR used a file very judiciously and trimmed the stop so that new covers would work.
RCCARDR photo
As for the drill comment, I found a thread on here where someone taped the frame to prevent damage and used a 1/2 inch hole saw with a 9mm center to very carefully trim the boss to allow the boss covers to fit snugly to the down tube. I suspect I could get by with just the tapping of the threads and a little - very little - filing.
https://www.bikeforums.net/classic-v...ter-style.html
brewerkz photo before
brewerkz during photo
brewerkz after photo
Starting again.
First I'd like to apologize because I didn't post any pictures.
Here is the shifter boss for my Ross Signature. Current shifters are Shimano Z401. These take a Shimano only proprietary bolt (machine screw?? lever Screw??). I recently acquired a partial Exage Sport groupset which included the shifter set but no bolts. I reached for some spare bolts and no, standard M5 shifter bolts don't work because the Z401 bosses are threaded for a smaller bolt size. I believe that the current bosses are Shimano A type bosses and require bolts that are referred to variously as M4.5 x .75 or 4.5mm x .75. They are ones referred to by JohnDThompson above.
Z401 and Exage Sport shifters
Exage on top and 401 on bottom
The original bolts are a MM or so too short to fit through the Sport shifters and engage the threads of the boss and the Exage require a different boss cover than the Z401 have.
401 base on top and Exage on bottom
I spoke with a local frame builder who suggested that rather than search for longer M4.5 bolts I should just tap the threads to take the M5 x .80 bolts. I would have had him tap it there and then but I didn't have the frame with me. He walked me through the tap process and it seemed straight forward.
I approached a neighbor who has lots of taps and other nice tools but he didn't have any 5mm taps. The neighbor suggested that I insert a drill bit into the bolt hole in the boss and drill into the frame and he said that drilling would prevent the tap from bottoming out and breaking in the threads (at least I think that's what he meant). Judging from the response on here, I guess that pre-drilling before tapping is not needed.
The neighbor suggested a local store to get the tap. I began to wonder if there waa certain thread size that I needed and now realize the .80 part of the M5 x .80 will cover that question.
This brings me to the next part where my post was confusing
The replacement boss covers won't fit onto the bosses and so the bosses must be modified or trimmed to allow the mounting of the new bosses. In his post RCCARDR used a file very judiciously and trimmed the stop so that new covers would work.
RCCARDR photo
As for the drill comment, I found a thread on here where someone taped the frame to prevent damage and used a 1/2 inch hole saw with a 9mm center to very carefully trim the boss to allow the boss covers to fit snugly to the down tube. I suspect I could get by with just the tapping of the threads and a little - very little - filing.
https://www.bikeforums.net/classic-v...ter-style.html
brewerkz photo before
brewerkz during photo
brewerkz after photo
#20
Generally bewildered
Join Date: Aug 2015
Location: Eastern PA, USA
Posts: 3,037
Bikes: 2014 Trek Domane 6.9, 1999 LeMond Zurich, 1978 Schwinn Superior
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1152 Post(s)
Liked 341 Times
in
251 Posts
Does M4.5 have the same pitch as M5? If not, when you try to drill and tap M5 where the M4.5 hole is, you will probably end up with a mess - there's not enough difference that the drill will clean out the M4.5 threads completely. If they are both coarse thread they are both .5mm pitch.
To throw another idea into the mix, if you are drilling a through-hole anyway, you might use a form tap rather than a cutting tap. The cutting tap would cut new grooves that may interlap with the old threads, and the interaction might tend to cause the tap to go in at the wrong angle. If that happens, the tap will likely break. Also, a cutting tap will remove metal without regards to whether that material is needed. A form tap will move the metal around. I think you'd get a better thread with a form tap.
That said, I'm pretty sure that this fastener is not super high stress (may be wrong- has anyone ever pulled one out or broken this type of screw in use?)
#21
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,515
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,398 Times
in
2,057 Posts
Thread
Thread Starter
Forum
Replies
Last Post
antidentite
Bicycle Mechanics
8
05-04-13 03:07 PM
ljsense
Bicycle Mechanics
16
02-16-12 10:35 PM