Cracked dropout
Likes For shoota:
Likes For Oneder:
#3
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,949
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 117 Post(s)
Tagged: 0 Thread(s)
Quoted: 1303 Post(s)
Liked 1,911 Times
in
1,141 Posts
Three options: First straighten everything and weld it back together. But caveates are the weld may break down the brass in the tubes that hold it in place between the stays. Second is to un-braze the drop out and replace it with a new one. Both will involve repainting the area repaired. In many cases more $ than it is worth to replace the frame as the third option. HTH, MH
Likes For Mad Honk:
#4
Senior Member
Thread Starter
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 7,827
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1872 Post(s)
Liked 692 Times
in
468 Posts
Three options: First straighten everything and weld it back together. But caveates are the weld may break down the brass in the tubes that hold it in place between the stays. Second is to un-braze the drop out and replace it with a new one. Both will involve repainting the area repaired. In many cases more $ than it is worth to replace the frame as the third option. HTH, MH
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
#5
Banned.
Join Date: Apr 2018
Posts: 821
Bikes: Wahoo of Theseus, others
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 428 Post(s)
Liked 67 Times
in
46 Posts
You can easily fix a small crack in a steel frame but this is not a crack it's a break in an important area and the welding most people can do won't be enough.
If you have taken some welding classes and have access to an arc welder you could fix it but it won't be 100% unless you put a new dropout on there as Mad Honk suggests and it seems doubtful it's worth the time, money and effort unless it's a very expensive frame.
If you have taken some welding classes and have access to an arc welder you could fix it but it won't be 100% unless you put a new dropout on there as Mad Honk suggests and it seems doubtful it's worth the time, money and effort unless it's a very expensive frame.
#6
Senior Member
Thread Starter
Join Date: Jun 2012
Location: Stillwater, OK
Posts: 7,827
Mentioned: 33 Post(s)
Tagged: 0 Thread(s)
Quoted: 1872 Post(s)
Liked 692 Times
in
468 Posts
You can easily fix a small crack in a steel frame but this is not a crack it's a break in an important area and the welding most people can do won't be enough.
If you have taken some welding classes and have access to an arc welder you could fix it but it won't be 100% unless you put a new dropout on there as Mad Honk suggests and it seems doubtful it's worth the time, money and effort unless it's a very expensive frame.
If you have taken some welding classes and have access to an arc welder you could fix it but it won't be 100% unless you put a new dropout on there as Mad Honk suggests and it seems doubtful it's worth the time, money and effort unless it's a very expensive frame.
__________________
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
2014 Cannondale SuperSix EVO 2
2019 Salsa Warbird
#7
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,084
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4205 Post(s)
Liked 3,866 Times
in
2,312 Posts
Gosh another gloom and doom reply with no context or deeper explanation. At least you do follow up with a more detailed reply that I do agree with.
Drop out replacement is a very real option. Whether it's the value the OP will choose is the real question. Yes a weld would secure this, and if done well perhaps for a long time. But these dropouts crack from a few reasons that welding won't fix. Like being over heated during the frame's brazing. There are many builders who have replaced the drop outs many times because of this kind of crack. Campy drop outs seem to be a common brand to see this. But then they are one of the more common brands too so a larger population. Andy
Drop out replacement is a very real option. Whether it's the value the OP will choose is the real question. Yes a weld would secure this, and if done well perhaps for a long time. But these dropouts crack from a few reasons that welding won't fix. Like being over heated during the frame's brazing. There are many builders who have replaced the drop outs many times because of this kind of crack. Campy drop outs seem to be a common brand to see this. But then they are one of the more common brands too so a larger population. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#8
Senior Member
Join Date: May 2019
Location: Bloomington, IN
Posts: 2,949
Bikes: Paramount, Faggin, Ochsner, Ciocc, Basso
Mentioned: 117 Post(s)
Tagged: 0 Thread(s)
Quoted: 1303 Post(s)
Liked 1,911 Times
in
1,141 Posts
Andy,
No doom and gloom here but there are problems with what I see to repair this drop out. A wire welder won't adequately repair the dropout, and would need a stick welder to fix it but the heat would be detrimental to the brazed joint at the chain/sear stay. As I said earlier this repair could be done with correct procedures in place. but will be costly. Smiles, MH
No doom and gloom here but there are problems with what I see to repair this drop out. A wire welder won't adequately repair the dropout, and would need a stick welder to fix it but the heat would be detrimental to the brazed joint at the chain/sear stay. As I said earlier this repair could be done with correct procedures in place. but will be costly. Smiles, MH
#9
Senior Member
Andy,
No doom and gloom here but there are problems with what I see to repair this drop out. A wire welder won't adequately repair the dropout, and would need a stick welder to fix it but the heat would be detrimental to the brazed joint at the chain/sear stay. As I said earlier this repair could be done with correct procedures in place. but will be costly. Smiles, MH
No doom and gloom here but there are problems with what I see to repair this drop out. A wire welder won't adequately repair the dropout, and would need a stick welder to fix it but the heat would be detrimental to the brazed joint at the chain/sear stay. As I said earlier this repair could be done with correct procedures in place. but will be costly. Smiles, MH
#10
Senior Member
Join Date: Jan 2013
Location: South Jersey
Posts: 2,266
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 714 Post(s)
Liked 800 Times
in
475 Posts
The proper welding process for repairing this is TIG. If done correctly, there will be minimal paint loss and no damage to the brass attaching it to the stay. That said, it won't fix the design flaw that allowed it to break in the first place.
Likes For dsaul:
#11
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,515
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,396 Times
in
2,056 Posts
A competent welder could repair that as well as add a small reinforcing plate across the opening.
Good picture too!
Good picture too!