Is this Rim Safe?
#1
Is this Rim Safe?
Hi all,
I have gotten several flats with this wheel and so decided to investigate the rim more closely thinking maybe there is a sharp edge inside somewhere. I took the tire/tube off and noticed the rim tape was not on straight and so not fully covering the spoke holes and thought this was the issue. I removed the old rim tape and planned to replace it but discovered this sharp protruding edge at the point where the two ends of the rim join together. Can I just file this sharp edge down flush with the inner rim surface or is this rim not safe and not salvageable? The outside rim braking surfaces are smooth with no gaps or cracks.
I have gotten several flats with this wheel and so decided to investigate the rim more closely thinking maybe there is a sharp edge inside somewhere. I took the tire/tube off and noticed the rim tape was not on straight and so not fully covering the spoke holes and thought this was the issue. I removed the old rim tape and planned to replace it but discovered this sharp protruding edge at the point where the two ends of the rim join together. Can I just file this sharp edge down flush with the inner rim surface or is this rim not safe and not salvageable? The outside rim braking surfaces are smooth with no gaps or cracks.
#2
Senior Member
If you are asking about the seam, then yes. I'm not a fan of C&V hookless clinchers, but with the proper tire, it's fine.
#3
#4
Senior Member
#5
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,341
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Liked 4,188 Times
in
2,471 Posts
The seam looks pretty typical and if the rim strip covers it I would have no concerns.
IIRC this rim does have rim bead hooks. What it doesn't have are the bead seating shelf and dropped center well that are more common these days. Andy
IIRC this rim does have rim bead hooks. What it doesn't have are the bead seating shelf and dropped center well that are more common these days. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#6
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 13,325
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Liked 4,333 Times
in
2,789 Posts
If you have anything sticking up and cutting the tape, by all means file it down. Just don't get aggressive and file beyond the inside channel (or extension of the channel at the gaps at the joint). Don't remove material to pretty up those gaps. They are fine. The rim is under close to pure compression there and the gaps don't hurt anything as long as they have rim tape stretched over them.
#7
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 39,647
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Liked 3,485 Times
in
1,913 Posts
Yes, you can certainly file the joint smoother if it helps you sleep at night
However, it won't make a difference unless the punctures are located there. Obviously, a burr opposite the valve can't cause a puncture elsewhere.
However, it won't make a difference unless the punctures are located there. Obviously, a burr opposite the valve can't cause a puncture elsewhere.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#8
It is hard to show what it feels like in the picture but it actually sticks up quite a but from the surface and has a sharp edge to it. Thanks to all who have replied here. I will carefully file it smooth to at least remove the sharp edge. Something had caused all the flat tires I got with this wheel. It was either this or the fact that the original rim tape did not cover all spoke holes.After smoothing it out I will apply new rim tape.
#9
Senior Member
Join Date: Jan 2014
Location: The banks of the River Charles
Posts: 2,051
Bikes: 2022 Salsa Beargrease, 2020 Seven Evergreen, 2019 Honey Allroads Ti, 2018 Seven Redsky XX, 2017 Trek Boon 7, 2014 Trek 520, 2006 Gary Fisher Montare
Liked 937 Times
in
497 Posts
Kinda kooks to me like the seam has cracked in the rim channel.
#10
Senior Member
Join Date: Jul 2015
Location: NW Oregon
Posts: 3,748
Bikes: !982 Trek 930R Custom, Diamondback ascent with SERIOUS updates, Fuji Team Pro CF, Specialized Sirrus Gravel convert '09 Comencal Meta 5.5
Liked 1,125 Times
in
802 Posts
i might take a minute to de-burr it, but filing it smooth isn't needed.. it's a high spot in the weld job... smooth it a bit and ride it.
#11
Senior Member
Join Date: Aug 2006
Location: Valley Forge: Birthplace of Freedom
Posts: 1,305
Bikes: Novara Safari, CAAD9, WABI Classic, WABI Thunder
Liked 460 Times
in
241 Posts
You may have luck with some emory cloth (like sandpaper for metal) and sand it, or dremel carefully.
__________________
Be watchful, stand firm in the faith, act like men, be strong. Let all that you do be done in love.
Be watchful, stand firm in the faith, act like men, be strong. Let all that you do be done in love.
#12
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 39,647
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Liked 3,485 Times
in
1,913 Posts
Either mount the tire with a reference lined up at the valve, or use a pen to make a reference there.
Then if you get a cut on the tread side, note and mark the tire there. For a cut on the rim side mark the rim.
This way you'll know if something is causing repeat flats, or they're random, unrelated events.
Note, rim side flats within an inch on either side of the valve usually have a unique cause specific to that location.
Likes For FBinNY:
#13
It is hard to show what it feels like in the picture but it actually sticks up quite a but from the surface and has a sharp edge to it. Thanks to all who have replied here. I will carefully file it smooth to at least remove the sharp edge. Something had caused all the flat tires I got with this wheel. It was either this or the fact that the original rim tape did not cover all spoke holes.After smoothing it out I will apply new rim tape.
#14
Senior Member
Wheel usable?
Hi all,
I have gotten several flats with this wheel and so decided to investigate the rim more closely thinking maybe there is a sharp edge inside somewhere. I took the tire/tube off and noticed the rim tape was not on straight and so not fully covering the spoke holes and thought this was the issue. I removed the old rim tape and planned to replace it but discovered this sharp protruding edge at the point where the two ends of the rim join together. Can I just file this sharp edge down flush with the inner rim surface or is this rim not safe and not salvageable? The outside rim braking surfaces are smooth with no gaps or cracks.
I have gotten several flats with this wheel and so decided to investigate the rim more closely thinking maybe there is a sharp edge inside somewhere. I took the tire/tube off and noticed the rim tape was not on straight and so not fully covering the spoke holes and thought this was the issue. I removed the old rim tape and planned to replace it but discovered this sharp protruding edge at the point where the two ends of the rim join together. Can I just file this sharp edge down flush with the inner rim surface or is this rim not safe and not salvageable? The outside rim braking surfaces are smooth with no gaps or cracks.
#15
Senior Member
It is hard to show what it feels like in the picture but it actually sticks up quite a but from the surface and has a sharp edge to it. Thanks to all who have replied here. I will carefully file it smooth to at least remove the sharp edge. Something had caused all the flat tires I got with this wheel. It was either this or the fact that the original rim tape did not cover all spoke holes.After smoothing it out I will apply new rim tape.
Nope, just not the best/prettiest weld job.
That's not a split, that's the seam where the two ends of the metal are joined. I'm going to guess from the look that the rim is initially pinned and than a quick weld on the inside to keep it from moving as extra insurance. That seam s readily available on lots of different rims and especially older rims since most were only pinned together and held just fine.
Likes For Russ Roth:
#16
I filed the rough edge down last night. No issues with that at all. Before doing anything else I decided to put the wheel in the truing stand. I got the side to side pretty true but the radial trueness is not great and there is a slight hop at the seam joint. I will try and see if I can improve it some more. I rode this wheel before and did not notice any hop but it definately does not run as true as any of the other wheels that I own.
#17
Senior Member
Lots of pinned rims don't always spin out perfectly round near the seam, in most of the instances I can recall the seam stuck out more to be more like a hop and between a 1/4 and full turn tighter of the two spokes that flank it have been needed to bring it closer into round there. Pinned rims can also be slightly out of alignment there are well, this is one of the reasons rims went to milled sidewalls, braking is significantly improved but the seam is also milled smooth and flat in the process. My limited experience with Wolber is that they were decent but softer which made them more prone to moving with small tweaks and easy to over adjust so a little more care needed, but still a decent wheel when built, just finding the difference between new materials, construction and shapes vs. older designs.
#19
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 6,358
Bikes: 1989 Cinelli Supercorsa
Liked 3,313 Times
in
1,992 Posts
There's nothing wrong with that rim.
Likes For smd4:
#20
#21
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 39,647
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Liked 3,485 Times
in
1,913 Posts
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#22
Senior Member
Join Date: Apr 2005
Location: Northern CA
Posts: 751
Bikes: Cannondale tandems: '92 Road, '97 Mtn. Mongoose 10.9 Ti, Kelly Deluxe, Tommaso Chorus, Cdale MT2000, Schwinn Deluxe Cruiser, Torker Unicycle, among others.
Liked 210 Times
in
131 Posts
The seam looks typical. But anything sharp should be smoothed.
HOWEVER, that spoke hole on the right? MAJOR burr sticking up! I'd want to be sure to address that as well as all the other spoke holes. Emery cloth will work, but a Dremel will make much quicker and cleaner work of it. I'd use one of their steel cutting bits with really fine teeth. It will throw really tiny aluminum shards, so be sure to maybe use a vacuum to catch 'em all and be sure the rim is clear of them all. Careful they can stick in your skin too!
Big cause of repeated flats is sharp spoke hole edges and cheapo rim strips. Under high road tire pressure, cheapo rim strip (rubber, for example) gets pushed into the spoke hole, exposing the edges, flatting your tube. Replace rim strips quality alternatives like Velox.
HOWEVER, that spoke hole on the right? MAJOR burr sticking up! I'd want to be sure to address that as well as all the other spoke holes. Emery cloth will work, but a Dremel will make much quicker and cleaner work of it. I'd use one of their steel cutting bits with really fine teeth. It will throw really tiny aluminum shards, so be sure to maybe use a vacuum to catch 'em all and be sure the rim is clear of them all. Careful they can stick in your skin too!
Big cause of repeated flats is sharp spoke hole edges and cheapo rim strips. Under high road tire pressure, cheapo rim strip (rubber, for example) gets pushed into the spoke hole, exposing the edges, flatting your tube. Replace rim strips quality alternatives like Velox.
#23
Thanks to all for these interesting ,and helpful comments. Yes, for sure I also noticed the spoke holes have the sharp edges. They will get covered by rim tape but will take care of the burr first. I may end up using this wheel on the trainer only even though I think it will be OK. Will see.