Totally Tubular
#3201
Senior Member
Join Date: Dec 2015
Location: San Diego
Posts: 740
Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima? 1998 Serotta Atlanta
Liked 206 Times
in
120 Posts
I just checked the pressure after a 20 hour wait. It dropped from 100psi to just below 20psi. So not the valve core.
I'll try to find time today to pull the wheel off, dunk in water to see if a leak is detectable and will add sealant. The current condition of the tread and sidewall doesn't merit a full-blown repair. This tire has given me nine years of use with no issues until now. Tubular life is good!
I'll try to find time today to pull the wheel off, dunk in water to see if a leak is detectable and will add sealant. The current condition of the tread and sidewall doesn't merit a full-blown repair. This tire has given me nine years of use with no issues until now. Tubular life is good!
#3202
Couldn’t possibly use anything other than an Italian-made engraver/scriber for keying the tyre bed of my Record Pave rims. Always scribed parallel lines on new rims back in the 80s/90s and never should have neglected that step last year when sandpaper didn’t scratch the surface…
__________________
Nothing quite says wall hanger like drillium toe straps
Nothing quite says wall hanger like drillium toe straps
#3203
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,919
Bikes: 82 Medici, 85 Ironman, 2011 Richard Sachs
Liked 2,236 Times
in
1,217 Posts
^The Horror!
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
Likes For Classtime:
#3204
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 13,019
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Liked 2,341 Times
in
1,036 Posts
Final report on my very slow leaking Schwalbe One tubular:
Sealant took care of the leak. The tire was still holding at 100psi this morning after adding Effetto Mariposa Caffelatex sealant yesterday morning and pumping to the same. Now I just have to ride the Paramount every week to keep the sealant from pooling at the bottom and hardening.
Sealant took care of the leak. The tire was still holding at 100psi this morning after adding Effetto Mariposa Caffelatex sealant yesterday morning and pumping to the same. Now I just have to ride the Paramount every week to keep the sealant from pooling at the bottom and hardening.
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Likes For pastorbobnlnh:
#3205
Senior Member
Join Date: Jan 2023
Posts: 538
Bikes: Two Peter Mooney customs, a 1980 Trek 510 townie, a Marin Stelvio set up for TTs.
Liked 342 Times
in
186 Posts
First, make sure the valve core is tight. If that doesn't do it, sealant. I've not had good luck locating a puncture by putting tire in water as the bubbles are really only indicating where the air is escaping from the casing and that may not coincide with where it is escaping the tube.
Last edited by MooneyBloke; 03-01-24 at 04:50 PM.
#3206
Senior Member
Join Date: Jan 2023
Posts: 538
Bikes: Two Peter Mooney customs, a 1980 Trek 510 townie, a Marin Stelvio set up for TTs.
Liked 342 Times
in
186 Posts
A small vessel of water and dish soap is even better I think. You brush it on generously, and where the air escapes, there is a large and obvious bubble.
#3208
Senior Member
Join Date: Dec 2015
Location: San Diego
Posts: 740
Bikes: 1978 Bruce Gordon, 1977 Lippy, 199? Lippy tandem, Bike Friday NWT, 1982 Trek 720, 2012 Rivendell Atlantis, 1983 Bianchi Specialissima? 1998 Serotta Atlanta
Liked 206 Times
in
120 Posts
Interesting. In four decades on sew-ups both garbage and excellent, I've never seen a displaced bubbles if the tire is in good shape. The path of least resistance is through the puncture or at least very close. I do pinch the tire to look for tread cuts in the area to be doubly sure though.
#3209
Senior Member
Join Date: Aug 2009
Location: Berkeley, CA
Posts: 7,382
Bikes: '72 Cilo Pacer, '72 Gitane Gran Tourisme, '72 Peugeot PX10, '73 Speedwell Ti, '74 Peugeot UE-8, '75 Peugeot PR-10L, '80 Colnago Super, '85 De Rosa Pro, '86 Look Equipe 753, '86 Look KG86, '89 Parkpre Team, '90 Parkpre Team MTB, '90 Merlin
Liked 2,686 Times
in
647 Posts
Interesting. In four decades on sew-ups both garbage and excellent, I've never seen displaced bubbles if the tire is in good shape. The path of least resistance is through the puncture or at least very close. I do pinch the tire to look for tread cuts in the area to be doubly sure though.
#3210
Senior Member
Join Date: Jan 2023
Posts: 538
Bikes: Two Peter Mooney customs, a 1980 Trek 510 townie, a Marin Stelvio set up for TTs.
Liked 342 Times
in
186 Posts
I've been riding tubulars since the 80s and I have also experienced what [MENTION=427857]L134[/MENTION] is describing. Not often, but more than a couple times. I have submerged a tubular to find small bubbles emanating from a general area of the sidewall (say a few inches long),
Valve hole bubbling might indeed be displaced, but when I've had that, it was leading to an irreparable failure of the stem on some Vitt CXes.
#3211
Senior Member
Join Date: May 2012
Location: Point Reyes Station, California
Posts: 4,631
Bikes: Indeed!
Liked 3,800 Times
in
1,197 Posts
A dried out casing may indeed give a false indication, but I try to touch up areas like that with latex emulsion because the bare casing is more prone to abrasion damage. In any case, pinching the tread around the bubbles should give you an idea where the damage lies.
Brent
__________________
"I have a tendency to meander sometimes." B.G.
"I have a tendency to meander sometimes." B.G.
#3212
Senior Member
Join Date: Jan 2023
Posts: 538
Bikes: Two Peter Mooney customs, a 1980 Trek 510 townie, a Marin Stelvio set up for TTs.
Liked 342 Times
in
186 Posts
Please share your source for liquid latex. In decades gone by I used the Jevelot product which came in a small jar that was good for many applications. Alas, Jevelot and Hugh Enochs are no more. I'd appreciate any lead on a substitute. I tried using tire sealant but it didn't adhere as well as my memory of the Jevelot product.
Brent
Brent
I also use this to stick the base tape back down after restitching cotton sew-ups. The main issue with either of these is the rather short shelf life once opened; in my experience, the rubber tends to fall out of suspension over time. Evidently carpet layers use some sort of latex emulsion as well, but I've not had any experience here. If you investigate this and can let me know of a good brand, I'd be very interested especially if it's cheaper than the Tear Mender.
Let me state loudly that I've never found a good base tape repair adhesive for Conti Sprinters. Those seem to be a one-and-done tire unless you like riding on dicey base tape.
Last edited by MooneyBloke; 03-06-24 at 10:44 AM.
Likes For MooneyBloke:
#3213
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 13,019
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Liked 2,341 Times
in
1,036 Posts
I finally had a chance to test-ride my sealant filled Schwalbe One tubular. 20 miles and no air loss! The ride also gave me a chance to check the road worthiness of the leather handlebar bag I just completed. More on the new bag can be found in the DIY Bag thread.
As mounted on my '71 P13 Paramount with other leather projects.
As mounted on my '71 P13 Paramount with other leather projects.
#3215
Freewheel Medic
Join Date: Oct 2005
Location: An Island on the Coast of GA!
Posts: 13,019
Bikes: Snazzy* Schwinns, Classy Cannondales & a Super Pro Aero Lotus (* Ed.)
Liked 2,341 Times
in
1,036 Posts
__________________
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Bob
Enjoying the GA coast all year long!
Thanks for visiting my website: www.freewheelspa.com
Likes For pastorbobnlnh:
#3216
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 25,043
Bikes: Several, mostly not name brands.
Liked 3,675 Times
in
2,077 Posts
Please share your source for liquid latex. In decades gone by I used the Jevelot product which came in a small jar that was good for many applications. Alas, Jevelot and Hugh Enochs are no more. I'd appreciate any lead on a substitute. I tried using tire sealant but it didn't adhere as well as my memory of the Jevelot product.
Brent
Brent
https://www.amazon.com/Liquid-Latex-...r_1_18?sr=8-18
Likes For JohnDThompson:
#3218
Full Member
Hey, sorry, this question is probably answered somewhere in this long thread, but are 22-23mm silk tubular tires with latex inner tubes for the road still being made? I’m in the US. Thanks in advance.
Last edited by Biker Pete; 03-07-24 at 07:17 PM.
#3219
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
__________________
Nothing quite says wall hanger like drillium toe straps
Nothing quite says wall hanger like drillium toe straps
Likes For seagrade:
#3220
Full Member
Available direct from FMB in France…
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
#3221
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 10,369
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Liked 3,474 Times
in
1,820 Posts
__________________
Life is too short not to ride the best bike you have, as much as you can.
Life is too short not to ride the best bike you have, as much as you can.
#3222
Full Member
rene herse has fmb https://www.renehersecycles.com/shop...-700c-x-23-mm/
#3223
Full Member
Available direct from FMB in France…
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
Last edited by Biker Pete; 03-31-24 at 07:24 AM.
Likes For Biker Pete:
#3224
Full Member
Available direct from FMB in France…
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
https://fm-boyaux.cc/en/route/28-82-.../36-largeur-22
No affiliation.
#3225
Senior Member
Join Date: Jan 2015
Location: Los Angeles
Posts: 4,919
Bikes: 82 Medici, 85 Ironman, 2011 Richard Sachs
Liked 2,236 Times
in
1,217 Posts
Just the tread?
__________________
I don't do: disks, tubeless, e-shifting, or bead head nymphs.
I don't do: disks, tubeless, e-shifting, or bead head nymphs.