Using different gears for wear prevention?
#1
Senior Member
Thread Starter
Join Date: Dec 2017
Location: Ontario
Posts: 53
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Using different gears for wear prevention?
Do any of you make a point to use differing gears so as not to wear out certain cogs prematurely?
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
#2
Senior Member
I'd rather wear out the cassette than start cross chaining and wearing out everything else.
I consider the cassette a wear and tear disposable item.
I consider the cassette a wear and tear disposable item.
#3
Senior Member
I shift for good cadence to not wear out my knees. I worry less about wearing cogs since they are easier to replace than knees.
Do you always go with same speed on flats? I naturally shift through most cogs by starting at 0 and riding at varying speeds at varying grades and wind.
Do you always go with same speed on flats? I naturally shift through most cogs by starting at 0 and riding at varying speeds at varying grades and wind.
Likes For HerrKaLeun:
#4
Tragically Ignorant
Join Date: Jun 2018
Location: New England
Posts: 15,613
Bikes: Serotta Atlanta; 1994 Specialized Allez Pro; Giant OCR A1; SOMA Double Cross Disc; 2022 Allez Elite mit der SRAM
Mentioned: 62 Post(s)
Tagged: 0 Thread(s)
Quoted: 8186 Post(s)
Liked 9,098 Times
in
5,054 Posts
The machine is supposed to prevent me from wearing out, the reverse definitely takes a back seat. I use the gears I need, and really don't care if it takes a few miles off a replaceable part.
Likes For livedarklions:
#5
Firm but gentle
Slightly Off Topic
I also worry about cog wear and drivetrain wear in general. This mindset has me usually installing a new chain about every 2500 to 3000 miles. I know there is about a rivet diameter of stretch at this point. The bike just seems to shift better and everything feels smoother with that brand new chain, could be mental. Part of me wants to be able to say “screw it, it’s just a bicycle, ride it till it skips”, but that will never happen.
#6
Senior Member
I guess it better than not using brakes because not wanting to buy new pads/rotors
Likes For mattleegee:
#7
In Real Life
Join Date: Jan 2003
Location: Down under down under
Posts: 52,152
Bikes: Lots
Mentioned: 141 Post(s)
Tagged: 0 Thread(s)
Quoted: 3203 Post(s)
Liked 596 Times
in
329 Posts
Do any of you make a point to use differing gears so as not to wear out certain cogs prematurely?
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
Why not just replace the 15 or 17 cogs when they wear out?
__________________
Rowan
My fave photo threads on BF
Century A Month Facebook Group
Machka's Website
Photo Gallery
Rowan
My fave photo threads on BF
Century A Month Facebook Group
Machka's Website
Photo Gallery
#8
Senior Member
Join Date: Jul 2006
Location: Lebanon (Liberty Hill), CT
Posts: 8,473
Bikes: CAAD 12, MASI Gran Criterium S, Colnago World Cup CX & Guru steel
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 1743 Post(s)
Liked 1,281 Times
in
740 Posts
Use the gears you need to use. Replace as needed.
Likes For bruce19:
#9
cowboy, steel horse, etc
Join Date: Sep 2008
Location: The hot spot.
Posts: 44,842
Bikes: everywhere
Mentioned: 71 Post(s)
Tagged: 1 Thread(s)
Quoted: 12771 Post(s)
Liked 7,687 Times
in
4,081 Posts
Do any of you make a point to use differing gears so as not to wear out certain cogs prematurely?
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
#10
Full Member
#11
climber has-been
Join Date: Dec 2004
Location: Palo Alto, CA
Posts: 7,111
Bikes: Scott Addict R1, Felt Z1
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 3432 Post(s)
Liked 3,566 Times
in
1,792 Posts
The fastest wear item in the drive train is the chain. But if you ride with a worn chain, you will also wear out your cassette.
No need to worry about overusing one cog, as long as you replace the chain before it’s worn. Check the chain for wear monthly.
Park Tool makes a chain wear checker that’s not expensive:
Chain Checker
No need to worry about overusing one cog, as long as you replace the chain before it’s worn. Check the chain for wear monthly.
Park Tool makes a chain wear checker that’s not expensive:
Chain Checker
Likes For terrymorse:
#12
• —
Join Date: Jun 2015
Location: Land of Pleasant Living
Posts: 12,234
Bikes: Shmikes
Mentioned: 59 Post(s)
Tagged: 0 Thread(s)
Quoted: 10167 Post(s)
Liked 5,862 Times
in
3,155 Posts
Definitely. I run my car in 4th on the highway half the time to spare the overdrive, too.
#13
Advanced Slacker
Join Date: Feb 2017
Posts: 6,210
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2762 Post(s)
Liked 2,537 Times
in
1,433 Posts
Hmmm, cross-chaining to prevent drivetrain wear.... interesting.
#14
Senior Member
Join Date: Apr 2011
Location: Alpharetta, GA
Posts: 15,280
Bikes: Nashbar Road
Mentioned: 71 Post(s)
Tagged: 0 Thread(s)
Quoted: 2934 Post(s)
Liked 341 Times
in
228 Posts
OK I'll admit it, I have selected gears for no other reason than to distribute wear. I don't shift as much as most, and sometimes I don't "shift" mentally from my fixed gear to road bike and might finish a ride without shifting at all. It's just a shame when the 16+/- are worn out and the rest of the cassette is pristine.
Likes For wphamilton:
#15
Señor Member
Join Date: Feb 2013
Posts: 5,066
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 649 Post(s)
Liked 292 Times
in
215 Posts
Cogs primarily wear out when they are used with a worn chain. Chains wear out from being ridden with inadequate lubrication and, eventually, over time. If you replace your chain before it get to the point where it is wearing the cogs, your cogs will not wear out.
#17
Senior Member
Join Date: Jul 2002
Location: Sacramento, California, USA
Posts: 40,865
Bikes: Specialized Tarmac, Canyon Exceed, Specialized Transition, Ellsworth Roots, Ridley Excalibur
Mentioned: 68 Post(s)
Tagged: 0 Thread(s)
Quoted: 2952 Post(s)
Liked 3,106 Times
in
1,417 Posts
Yeah, this is annoying. Particularly when you primarily ride on the flat lands and you're mostly in 3 or 4 cogs max.
Likes For TimothyH:
#20
Recreational Road Cyclist
Join Date: Sep 2013
Location: MetroWest, Mass.
Posts: 548
Bikes: 1990 Peter Mooney road bike
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 257 Post(s)
Liked 252 Times
in
134 Posts
Do any of you make a point to use differing gears so as not to wear out certain cogs prematurely?
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
I'm almost always in the 15 or 17 tooth cogs and middle chainring. I was just reading how the smaller cogs can wear out a chain quicker than larger ones. I'm gonna switch it up to 23 and 26 & the large chainring for a while. I do have concerns about crosschaining and extra noise but so be it.
The thread titled "Anyone Tracking Gear Usage" got me thinking about this.
#22
- Soli Deo Gloria -
Join Date: Aug 2015
Location: Northwest Georgia
Posts: 14,779
Bikes: 2018 Rodriguez Custom Fixed Gear, 2017 Niner RLT 9 RDO, 2015 Bianchi Pista, 2002 Fuji Robaix
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 6844 Post(s)
Liked 736 Times
in
469 Posts
Cassette and front ring wear can be minimized by using several chains throughout the life of one cassette.
I use three chains per cassette, cleaning and swapping about every 1000 miles for road, more frequent for gravel.
-Tim-
I use three chains per cassette, cleaning and swapping about every 1000 miles for road, more frequent for gravel.
-Tim-
#23
Tragically Ignorant
Join Date: Jun 2018
Location: New England
Posts: 15,613
Bikes: Serotta Atlanta; 1994 Specialized Allez Pro; Giant OCR A1; SOMA Double Cross Disc; 2022 Allez Elite mit der SRAM
Mentioned: 62 Post(s)
Tagged: 0 Thread(s)
Quoted: 8186 Post(s)
Liked 9,098 Times
in
5,054 Posts
If you really want to avoid wear, don't ride the bike.
Solutions can be worse than the problems they are intended to address. If your legs are ok with shifting for this purpose, no harm in doing it. If I were to shift for that purpose only, I would find it incredibly annoying because of my strong preference for high gears.
The better question might be if there's any way to buy bikes these days other than SS that don't have a bunch of gears we don't need?
Solutions can be worse than the problems they are intended to address. If your legs are ok with shifting for this purpose, no harm in doing it. If I were to shift for that purpose only, I would find it incredibly annoying because of my strong preference for high gears.
The better question might be if there's any way to buy bikes these days other than SS that don't have a bunch of gears we don't need?
#24
Senior Member
Join Date: Oct 2015
Location: San Diego, California
Posts: 4,077
Bikes: Velo Orange Piolet
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
Quoted: 2228 Post(s)
Liked 2,011 Times
in
972 Posts
I make a point of staying out of the small cogs unless I'm in the big chainring (I have triple cranks). In the past I have worn out the small cogs prematurely, so I try to avoid that.
#25
Banned
Join Date: Mar 2018
Location: Providence
Posts: 732
Bikes: Specialized tarmac sl2 giant tcx zero
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 319 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
I just use 30 dollar caasttea and a 30 dollar.chain and switch them out for the better ones on race day .