Go Back  Bike Forums > Search Forums
Reload this Page >

Search Results

Search
Notices
Search: Posts Made By: Bigbadjohn
Showing results 1 to 12 of 12
Search took 0.00 seconds.
09-17-22, 08:43 PM
Replies: 2
Views: 328
Posted By Doc_Wui

IF you're using the old BMS. it was connected to...

IF you're using the old BMS. it was connected to the switch. If you replaced the BMS in your rebuild, than you needed a BMS with an ON/OFF circuit.
09-10-22, 08:43 AM
Replies: 6
Views: 562
Posted By Doc_Wui

The "anti-theft power line" in their picture...

The "anti-theft power line" in their picture probably needs to be switched to battery power to start the controller.But their website never mentions that,

I sure would like to know what that 3.3...
09-06-22, 02:26 PM
Replies: 6
Views: 562
Posted By chas58

I do like having my batteries come with a switch....

I do like having my batteries come with a switch. Failing that, the controller can work, but I usually just jump the wires, or go to home depot and get a simple low voltage switch to plug in there.
09-05-22, 10:54 PM
Replies: 6
Views: 562
Posted By kracksmith

does it come with wiring instructions if so then...

does it come with wiring instructions if so then that is how it would work as you mentioned 2 reds.

Another switch I like is to have a switch turned off completely from battery to controller
...
09-05-22, 01:31 AM
Replies: 6
Views: 562
Posted By kracksmith

i would say one of those wire goes to a manual...

i would say one of those wire goes to a manual switch to turn on and off, of course the manual switch is a separate component
07-02-21, 05:27 AM
Replies: 22
Views: 5,091
Posted By Pop N Wood

Be very careful plugging two batteries together. ...

Be very careful plugging two batteries together. If they are at different charge levels you will get a massive spark and possibly a fire.

Not trying to scare you away, just trying to let you know...
04-05-21, 01:51 PM
Replies: 9
Views: 3,588
Posted By 2old

I'm out of my element now, and wouldn't recommend...

I'm out of my element now, and wouldn't recommend that. If DW can't help, you might try endless sphere. There are individuals there who do all sorts of conversions.
04-03-21, 08:25 PM
Replies: 9
Views: 3,588
Posted By Doc_Wui

Big Bad John, You're doing it to yourself again. ...

Big Bad John, You're doing it to yourself again.

I believe the orange connector with five wires is your phase wire connector,

The rest is yikes. I would suppose the white connector with thick...
02-21-21, 08:23 PM
Replies: 22
Views: 6,375
Posted By spinnanz

No keep the halls. Although that controller will...

No keep the halls. Although that controller will run without them it will be a little noisier than with hall sensors. Also without halls it will display the error code E08 on screen.
02-16-21, 07:39 PM
Replies: 22
Views: 6,375
Posted By Doc_Wui

Ifs it a geared motor? You can tell by spinning...

Ifs it a geared motor? You can tell by spinning it w/o power A geared motor will spin forward with less resistance. It will take more force to spin backwards because the gears have engaged and are...
11-14-20, 05:13 PM
Replies: 6
Views: 6,575
Posted By Doc_Wui

Is this a different bike from the one in your...

Is this a different bike from the one in your other post? Did you ever get that running? That would be the first thing to do, get a working ebike.

Some controllers will run the motor w/o a...
09-10-19, 08:00 PM
Replies: 9
Views: 4,343
Posted By Doc_Wui

The motors will run in general on any voltage,...

The motors will run in general on any voltage, but your controller may not be able to run on higher or lower voltage, Some of this may be component voltage ratings. Some of it may be hard wired...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.