Rack for bikes with fenders
#1
Senior Member
Thread Starter
Rack for bikes with fenders
Hi all. Perhaps there is a better subforum for this, but I didn’t see one. I’m looking for a hitch-mounted bike rack that will safely accommodate bikes with fenders. Seems like most of the good ones have the swing arm that clamps down on the front wheels (like this one) which will not be very friendly to fendered bikes.
All suggestions appreciated!
All suggestions appreciated!
#3
Swagman G10
I bought one of these last year for exactly this reason. A short length of pipe insulation helps provide additional top tube cushioning and protection. I have used it for local as well as day long interstate trips and am quite pleased.
#4
Senior Member
Thread Starter
#5
No, that's why I place a short length of pipe insulation around the top tube where the clamp contacts it. Easy!
#6
QR-disc must die!!!
Join Date: Sep 2018
Location: Shenandoah Valley, Northern Virginia.
Posts: 703
Bikes: '99 Trek 520, '20 Kona Sutra (FOR SALE 48cm), '21 Simon-Bikes mini-velo and a chromoly-framed folding bicycle with drop-bars and V-brakes, that rolls even while folded.
Likes: 0
Liked 199 Times
in
147 Posts
Any reasonably stocked bicycle shop should have numerous racks that are compatible with fenders. The bicycle itself is where the incompatibility would exist, as some do not have eyelets for racks.
#7
Senior Member
If you don’t want a rack that touches the frame, look at:
Saris Superclamp family
Thule Helium Platform (?)
Fender friendly wheel clamps and no pipe insulation required.
-mr. bill
Saris Superclamp family
Thule Helium Platform (?)
Fender friendly wheel clamps and no pipe insulation required.
-mr. bill
Last edited by mr_bill; 03-05-20 at 05:56 AM.
#8
Senior Member
Thread Starter
Those both appear to be precisely the type of rack that I would like to avoid: that clamp on the front wheel will damage a fender, I believe. Unless I am missing something?
#9
Senior Member
The clamps on the front wheel at 10:00 will NOT damage a fender. On the rear wheel, use a wheel strap.
If you don’t want to touch your tire, wheel, or frame get a rack where you remove the front wheel and clamp through the fork. If you don’t want to do that, I’m stumped.
-mr. bill
Last edited by mr_bill; 03-05-20 at 07:24 AM.
#10
Senior Member
Thread Starter
Read The Manual.
The clamps on the front wheel at 10:00 will NOT damage a fender. On the rear wheel, use a wheel strap.
If you don’t want to touch your tire, wheel, or frame get a rack where you remove the front wheel and clamp through the fork. If you don’t want to do that, I’m stumped.
-mr. bill
The clamps on the front wheel at 10:00 will NOT damage a fender. On the rear wheel, use a wheel strap.
If you don’t want to touch your tire, wheel, or frame get a rack where you remove the front wheel and clamp through the fork. If you don’t want to do that, I’m stumped.
-mr. bill
Or are you saying that the clamps are soft/gentle/whatever?
#11
Senior Member
-mr. bill
#12
Advanced Slacker
Join Date: Feb 2017
Posts: 6,252
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Liked 2,571 Times
in
1,451 Posts
The front arm is pushing back, and it is completely dependent on the rear strap to pull back against it. The cradle the rear wheel sits in is tilted the wrong way. Can it be tilted forward to push back against the force from the front wheel clamp? Is the position of it adjustable so that it can be slid back behind the center of the rear wheel?
The rear wheel strap (or any wheel strap) should be just keeping the bike from bouncing out. As pictured, it is mission critical to keep the bike in the rack at all, and under a bit of tension.
Maybe I am missing something, here.
@ OP: I think for full fendered bikes, a frame clamp is the best option. They are the most flexible solution out there. They are also not thrown off by front racks.
Of course, I have never had issues with racks that contact the frame causing any damage, even after roughly 40K miles of travel with several bikes all over the country. YMMV.
#13
Senior Member
Yeah, you take another look at the wheel trays in the picture. Think about why they are angled that way. The bike very simply can't "roll" out of the wheel trays if you use the wheel strap and tire clamp.
Hope you find what you are looking for. I wish you good luck in your search.
-mr. bill
Hope you find what you are looking for. I wish you good luck in your search.
-mr. bill
#14
Let's Ride!
Join Date: Jul 2008
Location: Triad, NC USA
Posts: 2,582
Bikes: --2010 Jamis 650b1-- 2016 Cervelo R2-- 2018 Salsa Journeyman 650B
Liked 40 Times
in
27 Posts
I think Mr Bill might be right but I have used a frame rack with straps holding the wheels in. I want to upgrade but I have a bike with fenders and it definitely limits some options.
#15
Advanced Slacker
Join Date: Feb 2017
Posts: 6,252
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Liked 2,571 Times
in
1,451 Posts
Yeah, you take another look at the wheel trays in the picture. Think about why they are angled that way. The bike very simply can't "roll" out of the wheel trays if you use the wheel strap and tire clamp.
Hope you find what you are looking for. I wish you good luck in your search.
-mr. bill
Hope you find what you are looking for. I wish you good luck in your search.
-mr. bill
Does the angle of the arms lock at different positions, such as 12 or 10 o’clock?
Just curious. I assume you have one of these and have used it with full coverage fenders, so I’ll take your word for it if it has worked out well.
Last edited by Kapusta; 03-05-20 at 10:04 AM.
#16
Senior Member
-mr. bill
#18
Junior Member
Several of our bikes have fenders and racks mounted, and when we were shopping for hitch-mount bike racks there were fewer options that officially supported carrying bikes with fenders. We ended up with the Thule EasyFold XT2. It isn't cheap, it isn't light, it isn't as quick and easy to attach / remove bikes, but it carries any of our bikes very securely.
https://www.thule.com/en-us/bike-rac...-xt-2-_-903202
https://www.thule.com/en-us/bike-rac...-xt-2-_-903202
#19
nothing to see here
I use a Kuat sherpa rack with a bike with metal portland design works fenders. I have transported it thousands of miles without any damage to the front fender. I do put a small microfiber cloth between the arm and the fender/fork area to protect the finish but that's it.
Last edited by Bryan C.; 03-08-20 at 11:11 AM.