40 year old Motobecane /bottom bracket creaky
#1
Junior Member
Thread Starter
40 year old Motobecane /bottom bracket creaky
So the time has come to do some important maintenance I have a bottom bracket creek. Sometimes it goes away for a while. It isn't very bad but hampers the enjoyment of the bike and can't be very good for it . I would like to do something about it myself . I don't have a bike stand or have I done this before .
what tools would I need ?
what is the procedure?
What grease do I need?
is repacking bearings part of it ?
Thank's
what tools would I need ?
what is the procedure?
What grease do I need?
is repacking bearings part of it ?
Thank's
#2
Senior Member
Join Date: Nov 2019
Location: Iowa
Posts: 682
Bikes: 2021 Salsa Fargo 1x12, 2019 Jamis Renegade Exploit 1x11. Motobacne NX Fat Tire
Liked 332 Times
in
170 Posts
So the time has come to do some important maintenance I have a bottom bracket creek. Sometimes it goes away for a while. It isn't very bad but hampers the enjoyment of the bike and can't be very good for it . I would like to do something about it myself . I don't have a bike stand or have I done this before .
what tools would I need ?
what is the procedure?
What grease do I need?
is repacking bearings part of it ?
Thank's
what tools would I need ?
what is the procedure?
What grease do I need?
is repacking bearings part of it ?
Thank's
#3
Blamester
Pour some oil in the bearings might fix it good enough.
Its forty years old and unless you replace it's never going to be perfect.
And everything could be seized and a pain to take apart.
Is it a cottered crank?
If it is you could give them a spray penetrating oil and then a tap of a hammer and snug up the bolt if it moves. If it doesn't it's good.
I don't know what tools specifically you would need to service but it might be a lot.
You could end up needing a drill or a torch.
Its forty years old and unless you replace it's never going to be perfect.
And everything could be seized and a pain to take apart.
Is it a cottered crank?
If it is you could give them a spray penetrating oil and then a tap of a hammer and snug up the bolt if it moves. If it doesn't it's good.
I don't know what tools specifically you would need to service but it might be a lot.
You could end up needing a drill or a torch.
#4
Junior Member
Thread Starter
Thanks for the replies It it functions pretty well I'll try what I can. I don't know what kind of crank it has . Perhaps someone here would know. I would appreciate any suggestions
Thank you again
Thank you again
#5
Banned.
There is a bottom bracket tool, what one depends on what your bottom bracket is. You will take it off and see what's in there. Probably cup and cone bearings but they might be in a race. Probably 1/4 inch but possibly slightly smaller. Just take them out and see what you have, then get new bearings of the right size they are cheap. Grease them up and put everything back together. If you can't find the right tool you can use a hammer and chisel to unscrew it.
#6
Junior Member
Thread Starter
There is a bottom bracket tool, what one depends on what your bottom bracket is. You will take it off and see what's in there. Probably cup and cone bearings but they might be in a race. Probably 1/4 inch but possibly slightly smaller. Just take them out and see what you have, then get new bearings of the right size they are cheap. Grease them up and put everything back together. If you can't find the right tool you can use a hammer and chisel to unscrew it.
#7
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,889
Bikes: Old Steelies I made, Old Cannondales
Liked 1,013 Times
in
648 Posts
Loose cotter pins ?
Post some close up pictures of the cranks from a couple of angles.
Post some close up pictures of the cranks from a couple of angles.
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#8
Junior Member
Thread Starter
I have not posted any pictures yet I just crossed the threshold of 10 posts so I should be able to. But I tried earlier today it didn't work maybe I have to change the size of the picture, will post as soon as I can. thank you for your communication , along with the others too.
I remember this bike being much more enjoyable ,a few years ago quite fast and smooth but now, something is missing.
I spun the rear wheel freewheeling it and it spun very freely but not smooth there was vibration but thats' another story.
regards
Alex
#9
O.K would love too .
I have not posted any pictures yet I just crossed the threshold of 10 posts so I should be able to. But I tried earlier today it didn't work maybe I have to change the size of the picture, will post as soon as I can. thank you for your communication , along with the others too.
I remember this bike being much more enjoyable ,a few years ago quite fast and smooth but now, something is missing.
I spun the rear wheel freewheeling it and it spun very freely but not smooth there was vibration but thats' another story.
regards
Alex
I have not posted any pictures yet I just crossed the threshold of 10 posts so I should be able to. But I tried earlier today it didn't work maybe I have to change the size of the picture, will post as soon as I can. thank you for your communication , along with the others too.
I remember this bike being much more enjoyable ,a few years ago quite fast and smooth but now, something is missing.
I spun the rear wheel freewheeling it and it spun very freely but not smooth there was vibration but thats' another story.
regards
Alex
#10
Full Member
For a great intro on all things bicycle I'd suggest you look at Lennard Zinn's bicycle maintenace book, any edition will be fine for a 40 year old Motobecane. This will show you just about all options. You Tube of course can help also.
Likes For Steelman54:
#11
Senior Member
Join Date: Apr 2020
Posts: 331
Bikes: '68 Masi Special road, Grail bike
Likes: 0
Liked 70 Times
in
58 Posts
is it the bottom bracket that creaks or the cranks? cotterless cranks will creak if
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
#12
Junior Member
Thread Starter
now we can see it though .
#13
Junior Member
Thread Starter
is it the bottom bracket that creaks or the cranks? cotterless cranks will creak if
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
so do you suppose she has a cottered or cotterless crank ??
I would like to get that book Zinn thanks for the suggestion ( ebay)
#14
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,664
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Liked 633 Times
in
436 Posts
EDIT: Here's a cottered crank from another old Motobecane (Mirage, new in 1975). The top of the cotter pin (It's not like what we think of when we say "cotter pin") is visible sticking out of the crank.
1975 Motobecane crank and chainrings
Last edited by sweeks; 06-03-20 at 06:45 PM.
#15
Senior Member
It's a basic square taper bottom bracket. They are surprisingly easy to do maintenance on, and when adjusted correctly spin as well as upscale new ones. You need this tool, https://www.parktool.com/product/cra...ttom%20Bracket to remove the crank bolts. Use this one to remove the crank arms from spindles https://www.parktool.com/product/uni...ttom%20Bracket (requires an adjustable wrench). Use this one to remove the lock ring on the non drive side
cup https://www.parktool.com/product/adj...ttom%20Bracket and this one to remove the non drive side cup https://www.parktool.com/product/cra...ttom%20Bracket. Then remove the spindle. The bearings will probably be "caged" bearings instead of "loose" (this will make sense once you remove the non drive side cup). Finally, remove the drive side cup. After forty years this may be difficult. You may need to use a threaded rod with a fender washer and nut on the non drive side, fit an adjustable wrench to the cup and then put a nut on the outside of the adjustable wrench so you can tap it with a hammer without it falling off. VERY important, the drive side cup is reverse threaded, meaning it's lefty (counterclockwise) tighty, righty (clockwise) loosey. You can then clean everything, regrease, put in new bearings (1/4"). You can either clean the cage and put bearings back into the cage, or you can pitch the cage and use loose bearings (which will make it spin more smoothly). For number of bearings, fill each cup and then remove one bearing. That's the correct number. Put everything back on in reverse. Google to learn now to correctly tighten everything using the non drive side cup and lock ring. Easy!
cup https://www.parktool.com/product/adj...ttom%20Bracket and this one to remove the non drive side cup https://www.parktool.com/product/cra...ttom%20Bracket. Then remove the spindle. The bearings will probably be "caged" bearings instead of "loose" (this will make sense once you remove the non drive side cup). Finally, remove the drive side cup. After forty years this may be difficult. You may need to use a threaded rod with a fender washer and nut on the non drive side, fit an adjustable wrench to the cup and then put a nut on the outside of the adjustable wrench so you can tap it with a hammer without it falling off. VERY important, the drive side cup is reverse threaded, meaning it's lefty (counterclockwise) tighty, righty (clockwise) loosey. You can then clean everything, regrease, put in new bearings (1/4"). You can either clean the cage and put bearings back into the cage, or you can pitch the cage and use loose bearings (which will make it spin more smoothly). For number of bearings, fill each cup and then remove one bearing. That's the correct number. Put everything back on in reverse. Google to learn now to correctly tighten everything using the non drive side cup and lock ring. Easy!
__________________
Don't complain about the weather and cower in fear. It's all good weather. Just different.
Don't complain about the weather and cower in fear. It's all good weather. Just different.
Likes For revcp:
#16
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,664
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Liked 633 Times
in
436 Posts
If the Bottom bracket hasn't been serviced in 40 years, be prepared to find wear, rust, and who knows what. I just finished re-building the Motobecane whose crank I showed elsewhere. It involved replacing the crank axle and the bearings, but it was worth the effort IMO.
EDIT: Good advice ^^ from revcp. You don't actually have to remove the drive-side cup unless it's in bad shape. Usually the crank axle races are ruined long before the cups. I left my DS cup in place. I also replaced the caged bearings (7 ball per side) with uncaged balls... 11 per side. Better load bearing and longer service life.
BB Lockring wrench
Last edited by sweeks; 06-03-20 at 07:07 PM.
#17
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,889
Bikes: Old Steelies I made, Old Cannondales
Liked 1,013 Times
in
648 Posts
Start by making sure everything's tight.
Sometimes you can isolate noises by stressing each part as individually as possible.
For instance, standing next to the bike, squeezing both brakes, and the pedal at "3-oclock" step hard on the pedal, release, step hard again.
Repeat on the other side.
Also, when you notice it while riding, pay close attention to what type of effort causes it
Sometimes you can isolate noises by stressing each part as individually as possible.
For instance, standing next to the bike, squeezing both brakes, and the pedal at "3-oclock" step hard on the pedal, release, step hard again.
Repeat on the other side.
Also, when you notice it while riding, pay close attention to what type of effort causes it
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#18
Senior Member
Join Date: Jun 2014
Location: Ontario, Canada
Posts: 4,626
Bikes: iele Latina, Miele Suprema, Miele Uno LS, Miele Miele Beta, MMTB, Bianchi Model Unknown, Fiori Venezia, Fiori Napoli, VeloSport Adamas AX
Liked 934 Times
in
646 Posts
For grease I just use a decent marine grease. It's totally waterproof and requires a good scrubbing with soap and a stiff-bristle brush to get it off.
You need a socket or special wrench that fits your nut on the bottom bracket spindle - usually 14mm but sometimes 15mm. Those a re the two most common sizes.
Then you need a crank extractor aka puller that screws into the threads on the arms of you crankarms.
A pair of large slip-joint pliers can be used in a pinch to undo the lockring on t he left side of the bottom bracket. A pin tool is usually uused to unscrew the adjustable cup. Your appears to be a large nut. If so, then a large adjustable wrench might fit it.
So, with luck t he only tool you might need to buy is the crankarm extractor/puller.
I'd clean the inside of the cups really well and then put in new ball bearings. Use lots of grease. I put grease in the cups wherethe bearings will go and also on the bearings themselves if caged.
Cheers
You need a socket or special wrench that fits your nut on the bottom bracket spindle - usually 14mm but sometimes 15mm. Those a re the two most common sizes.
Then you need a crank extractor aka puller that screws into the threads on the arms of you crankarms.
A pair of large slip-joint pliers can be used in a pinch to undo the lockring on t he left side of the bottom bracket. A pin tool is usually uused to unscrew the adjustable cup. Your appears to be a large nut. If so, then a large adjustable wrench might fit it.
So, with luck t he only tool you might need to buy is the crankarm extractor/puller.
I'd clean the inside of the cups really well and then put in new ball bearings. Use lots of grease. I put grease in the cups wherethe bearings will go and also on the bearings themselves if caged.
Cheers
#19
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 25,052
Bikes: Several, mostly not name brands.
Liked 3,684 Times
in
2,080 Posts
It's not clear from your picture who made your crank. If it is TA or Stronglight, you will need the proprietary extractor tool to remove the arms. A Motobécane of that era will likely have a metric thread bottom bracket, which limits your choices of replacement parts, should that be needed. Velo-Orange and Phil Wood offer metric thread cartridges, and there are threadless options from Velo-Orange and others that can work.
#20
Senior Member
Join Date: Apr 2020
Posts: 331
Bikes: '68 Masi Special road, Grail bike
Likes: 0
Liked 70 Times
in
58 Posts
pics are not good but I could tell that it's a 5-pin crank so it is either TA
or Stronglight. if the year is late enough the extractor threads will be standard
22mm but if earlier it would be 23mm and 23.35 respectively. closely measure
the threads b4 buying the tool(crank puller/extractor)
also noticed a Huret Jubile cable guide (the most elegant one ever)
or Stronglight. if the year is late enough the extractor threads will be standard
22mm but if earlier it would be 23mm and 23.35 respectively. closely measure
the threads b4 buying the tool(crank puller/extractor)
also noticed a Huret Jubile cable guide (the most elegant one ever)
#21
When you finish servicing the BB, put some anti-seize on the axle flats before reinstalling the crank arms. I can't tell you how many creaky-weaky noises I've made disappear with a liberal application of anti-sieze.
#22
Junior Member
Thread Starter
is it the bottom bracket that creaks or the cranks? cotterless cranks will creak if
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
they're loose ( they don't have to feel loose to be loose enough to creak)
cottered cranks creak when the swedge is coming loose between the arm and the
spider or chainring. if it's actually the bottom bracket the creak is usually because
the right side or fixed cup is loose. once again it doesn't have to feel loose to
be loose enough to creak
#23
Full Member
Could also be the saddle, pedals, stem, handlebar or the frame itself. Did You isolate the bb area ad the culprit just by ear or did You do some other testing?
#24
Junior Member
Thread Starter
Start by making sure everything's tight.
Sometimes you can isolate noises by stressing each part as individually as possible.
For instance, standing next to the bike, squeezing both brakes, and the pedal at "3-oclock" step hard on the pedal, release, step hard again.
Repeat on the other side.
Also, when you notice it while riding, pay close attention to what type of effort causes it
Sometimes you can isolate noises by stressing each part as individually as possible.
For instance, standing next to the bike, squeezing both brakes, and the pedal at "3-oclock" step hard on the pedal, release, step hard again.
Repeat on the other side.
Also, when you notice it while riding, pay close attention to what type of effort causes it
pics are not good but I could tell that it's a 5-pin crank so it is either TA
or Stronglight. if the year is late enough the extractor threads will be standard
22mm but if earlier it would be 23mm and 23.35 respectively. closely measure
the threads b4 buying the tool(crank puller/extractor)
also noticed a Huret Jubile cable guide (the most elegant one ever)
or Stronglight. if the year is late enough the extractor threads will be standard
22mm but if earlier it would be 23mm and 23.35 respectively. closely measure
the threads b4 buying the tool(crank puller/extractor)
also noticed a Huret Jubile cable guide (the most elegant one ever)
Next I am going to go non-cage and want very good bearing what do you recommend please, and how many ?
By for now , cheers.
And thanks to all that are continuing to give me advice .
#25
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,889
Bikes: Old Steelies I made, Old Cannondales
Liked 1,013 Times
in
648 Posts
Sounds like the bottom bracket is a bit loose. You can try the same test with your and, for better feel. Hold the pedal, put a little forward pressure on it, then push-pull the pedal toward the bike, and away from it. Do you feel any play ?
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html