Di2 Wire tight across handlebars
#1
Di2 Wire tight across handlebars
Hi! I just got a new bike with Ultegra Di2. There's not much slack at all in the wire that runs from one hood to the other on the handlebars. Sliding a garmin mount under that wire makes the fit pretty tight. Is this anything to worry about (pressure on it/something popping out)?
If I wanted to fit a bike light on the handlebar there's zero room.
Thanks!
If I wanted to fit a bike light on the handlebar there's zero room.
Thanks!
#3
Senior Member
Join Date: Nov 2015
Location: Music City, USA
Posts: 4,444
Bikes: bikes
Liked 1,429 Times
in
711 Posts
I would be worried to some extent if it's so tight you with a Garmin under it, but at the same time, that's an area that shouldn't ever really move either on its own, though if there was an incident and your hoods moved it could pop out, I guess.
Do you have two wires running to an external junction box or is it internal? The two external wires would probably be about 55 bucks. Not sure about the internal. Up to you if it's worth it for the piece of mind. I'd probably leave it myself.
Do you have two wires running to an external junction box or is it internal? The two external wires would probably be about 55 bucks. Not sure about the internal. Up to you if it's worth it for the piece of mind. I'd probably leave it myself.
#4
I would be worried to some extent if it's so tight you with a Garmin under it, but at the same time, that's an area that shouldn't ever really move either on its own, though if there was an incident and your hoods moved it could pop out, I guess.
Do you have two wires running to an external junction box or is it internal? The two external wires would probably be about 55 bucks. Not sure about the internal. Up to you if it's worth it for the piece of mind. I'd probably leave it myself.
Do you have two wires running to an external junction box or is it internal? The two external wires would probably be about 55 bucks. Not sure about the internal. Up to you if it's worth it for the piece of mind. I'd probably leave it myself.
With the garmin mount it is tight but reasonable. I installed a bike light mount over the wire since there's no way to get it under.
Does that type of wiring for Di2 seem normal? I'm going to call the bike shop when it opens to ask. Pictures of my bike online don't seem to have it that way.
#5
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
#6
Senior Member
Do not do this.
Mine is set up the same way. Next time the bike is in the shop and is due for new handlebar tape, I will ask them to put in a longer wire -- or, if there is slack under the tape, to let some of it out. (My bike has about 6500 miles on it, but I got a new headlight this year with a burly mount.)
In the meantime, you have options. If putting your light mount over the wire makes you nervous, move it over a bit so that it is over the tape - that will protect the wire.
Mine is set up the same way. Next time the bike is in the shop and is due for new handlebar tape, I will ask them to put in a longer wire -- or, if there is slack under the tape, to let some of it out. (My bike has about 6500 miles on it, but I got a new headlight this year with a burly mount.)
In the meantime, you have options. If putting your light mount over the wire makes you nervous, move it over a bit so that it is over the tape - that will protect the wire.
Likes For Koyote:
#7
Longer Di2 wire would be the easiest but I would go with drilling the bars and running a 1200 mm cable internally.
Check out this video by Rides of Japan
Check out this video by Rides of Japan
#8
FLIR Kitten to 0.05C
Join Date: Sep 2014
Location: Lincoln, Nebraska
Posts: 5,331
Bikes: Roadie: Seven Axiom Race Ti w/Chorus 11s. CX/Adventure: Carver Gravel Grinder w/ Di2
Liked 407 Times
in
255 Posts
Thanks for the response! The junction box is in the bar end. The bike shop could not get a hold of the normal handlebars that this bike comes with (Giant TCR) so they used a Zipp aluminum bar. There is a wire running from one hood to the other and goes across the face plate of the stem (tightly).
With the garmin mount it is tight but reasonable. I installed a bike light mount over the wire since there's no way to get it under.
Does that type of wiring for Di2 seem normal? I'm going to call the bike shop when it opens to ask. Pictures of my bike online don't seem to have it that way.
With the garmin mount it is tight but reasonable. I installed a bike light mount over the wire since there's no way to get it under.
Does that type of wiring for Di2 seem normal? I'm going to call the bike shop when it opens to ask. Pictures of my bike online don't seem to have it that way.
There are several ways to wire a cockpit, it depends on the parts you have.
#9
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 7,316
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Liked 2,396 Times
in
1,352 Posts
If the under stem A junction, it's 4 holes, 2 at the stem, 2 at each shifter.
But why ?, just tape the E-Tune wire alongside the brake housings, it's under bar tape the entire time.
This would certainly be a "I'm really bored this winter" project.
But why ?, just tape the E-Tune wire alongside the brake housings, it's under bar tape the entire time.
This would certainly be a "I'm really bored this winter" project.
#10
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
Easy solution....
Sram eTap
Problem solved
Sram eTap
Problem solved
#12
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
#13
Senior Member
Likes For Chi_Z:
#14
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
#15
serious cyclist
Join Date: Apr 2009
Location: Austin
Posts: 21,147
Bikes: S1, R2, P2
Liked 3,685 Times
in
2,028 Posts
#16
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
#17
serious cyclist
Join Date: Apr 2009
Location: Austin
Posts: 21,147
Bikes: S1, R2, P2
Liked 3,685 Times
in
2,028 Posts
#18
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
#19
serious cyclist
Join Date: Apr 2009
Location: Austin
Posts: 21,147
Bikes: S1, R2, P2
Liked 3,685 Times
in
2,028 Posts
#20
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
I put 12,000 miles on Rival 10 speed with no problem on a Trek Madone 4.6. 6000 miles in Rival CX1 on a Cannondale SuperX. 4500 miles on Red 22 on a Trek Emonda SLR and 26,000 miles on the same Emonda but with Red eTap.
I can count the number of chain drops on 1 hand.
Your sampling is minimal and I suggest it's "user" error. And you have no problem bad mouthing then entire product line. Sounds fair to me.
#21
serious cyclist
Join Date: Apr 2009
Location: Austin
Posts: 21,147
Bikes: S1, R2, P2
Liked 3,685 Times
in
2,028 Posts
Well...
I put 12,000 miles on Rival 10 speed with no problem on a Trek Madone 4.6. 6000 miles in Rival CX1 on a Cannondale SuperX. 4500 miles on Red 22 on a Trek Emonda SLR and 26,000 miles on the same Emonda but with Red eTap.
I can count the number of chain drops on 1 hand.
Your sampling is minimal and I suggest it's "user" error. And you have no problem bad mouthing then entire product line. Sounds fair to me.
I put 12,000 miles on Rival 10 speed with no problem on a Trek Madone 4.6. 6000 miles in Rival CX1 on a Cannondale SuperX. 4500 miles on Red 22 on a Trek Emonda SLR and 26,000 miles on the same Emonda but with Red eTap.
I can count the number of chain drops on 1 hand.
Your sampling is minimal and I suggest it's "user" error. And you have no problem bad mouthing then entire product line. Sounds fair to me.
Oh and two of my friends crashed at IMWisconsin because of the queued shifts issue. I'm sure that's just user error and small sample size, though. As it is for everyone else who has that issue.
#22
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
I had a shifter fall apart in my hand, which is slightly more memorable than a chain drop. The first thing you've said that's right, though, is that I have no problem bad-mouthing the entire product line. If Shimano can't get the new DA out in time for my new bike (either released or available) I'll probably just go Chorus. SRAM can piss up a rope.
Oh and two of my friends crashed at IMWisconsin because of the queued shifts issue. I'm sure that's just user error and small sample size, though. As it is for everyone else who has that issue.
Oh and two of my friends crashed at IMWisconsin because of the queued shifts issue. I'm sure that's just user error and small sample size, though. As it is for everyone else who has that issue.
Why not just stick with Shimano? The extra gear can't be that much of a difference. So you'll go with Campy which isn't compatible with your other bikes.
#23
Well...
I put 12,000 miles on Rival 10 speed with no problem on a Trek Madone 4.6. 6000 miles in Rival CX1 on a Cannondale SuperX. 4500 miles on Red 22 on a Trek Emonda SLR and 26,000 miles on the same Emonda but with Red eTap.
I can count the number of chain drops on 1 hand.
Your sampling is minimal and I suggest it's "user" error. And you have no problem bad mouthing then entire product line. Sounds fair to me.
I put 12,000 miles on Rival 10 speed with no problem on a Trek Madone 4.6. 6000 miles in Rival CX1 on a Cannondale SuperX. 4500 miles on Red 22 on a Trek Emonda SLR and 26,000 miles on the same Emonda but with Red eTap.
I can count the number of chain drops on 1 hand.
Your sampling is minimal and I suggest it's "user" error. And you have no problem bad mouthing then entire product line. Sounds fair to me.
Likes For blakcloud:
#24
On Your Left
Join Date: Nov 2011
Location: Long Island, New York, USA
Posts: 8,373
Bikes: Trek Emonda SLR, Sram eTap, Zipp 303
Liked 2,435 Times
in
1,187 Posts
GlennR is this another thread you are going to hijack that has absolutely nothing to do with the OP's question? You will then post ten times trying to prove how right you are, because your experience is what everyone else experiences and if they don't it's their fault. Give it a break, it has nothing to do with the question at hand. Maybe, you should read post #1 again and if you can solve that problem with the wire then add something useful. Your posts are tiresome and add nothing of value.
When someone posts something as a fact with limited proof, I'll will point it out.
Remember, it takes 2.
I'm also waiting for a reply to post #5.
What did the LBS say, after all they built it.
The optimist says "the glass is half full"
The pessimist says "the glass is half empty"
Th engineer says "why is the glass so large?"
Last edited by GlennR; 11-22-20 at 07:39 PM.
#25
Di2 fanatic
Ignoring the SRAM / Shimano arguments (just ride your bike, who cares what groupset people use), I'd like to add:
If the wire is only tight across the handlebars then that is fine. I mean.. I wouldn't want to ride around on a bike with a wire dangling quite a bit below the handlebar. If you're going to run a wire across from left to right, you better make sure it's tight and sticks as close to the handlebar as possible.
I would not run a wire across the handlebar myself, but that's up to you / LBS.
That said, there should definitely be excess wire / slack at the shift lever itself, or anywhere it plugs into another component. If there is not, you run the risk of accidentally unplugging wires if a shift lever moves or if you grab the bars (or that dangling wire).
At the levers it should look something like this:
If the wire is only tight across the handlebars then that is fine. I mean.. I wouldn't want to ride around on a bike with a wire dangling quite a bit below the handlebar. If you're going to run a wire across from left to right, you better make sure it's tight and sticks as close to the handlebar as possible.
I would not run a wire across the handlebar myself, but that's up to you / LBS.
That said, there should definitely be excess wire / slack at the shift lever itself, or anywhere it plugs into another component. If there is not, you run the risk of accidentally unplugging wires if a shift lever moves or if you grab the bars (or that dangling wire).
At the levers it should look something like this: