Shimano STI brake hoods...Best way to remove?
#1
Senior Member
Thread Starter
Join Date: Mar 2016
Location: North of Boston
Posts: 905
Bikes: 1973 Schwinn Sports Tourer plus a " few" more :)
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 212 Post(s)
Liked 202 Times
in
148 Posts
Shimano STI brake hoods...Best way to remove?
I need to remove a pastor shimano sti 5500 brake hoods.
I want to save them and clean them.
Would like to know from the many experts here, the best way to do.
I can just see the side I side piece where the cable goes could be more than a challenge
As always......appreciate your help and time
I want to save them and clean them.
Would like to know from the many experts here, the best way to do.
I can just see the side I side piece where the cable goes could be more than a challenge
As always......appreciate your help and time
#2
Senior Member
Join Date: Aug 2010
Location: Wurundjeri Country
Posts: 2,483
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 1087 Post(s)
Liked 1,916 Times
in
936 Posts
Carefully. A hairdryer is handy just to make the rubber a bit more compliant. I found getting them on was harder than getting them off. YMMV.
#3
Thread derailleur
Join Date: Mar 2004
Location: Glendora, CA
Posts: 668
Bikes: Croll '94 & Cannondale Supersix '15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 378 Post(s)
Liked 478 Times
in
275 Posts
I accomplished this best by removing the shifter from the handlebar.
Little bit of soapy water solution and pull off.
Little bit of soapy water solution and pull off.
Likes For roadcrankr:
#4
aka: Dr. Cannondale
Join Date: Jul 2009
Posts: 7,761
Mentioned: 235 Post(s)
Tagged: 0 Thread(s)
Quoted: 2168 Post(s)
Liked 3,500 Times
in
1,226 Posts
I use a hair dryer to warm them up and then a squirt of lighter fluid from each end to make them slippery.
I also pull them off from the bar end.
BUT they are old, so no matter what you do they might split.
I also pull them off from the bar end.
BUT they are old, so no matter what you do they might split.
__________________
Hard at work in the Secret Underground Laboratory...
Hard at work in the Secret Underground Laboratory...
#5
Ride, Wrench, Swap, Race
Join Date: Jan 2010
Location: Northern California
Posts: 9,205
Bikes: Cheltenham-Pedersen racer, Boulder F/S Paris-Roubaix, Varsity racer, '52 Christophe, '62 Continental, '92 Merckx, '75 Limongi, '76 Presto, '72 Gitane SC, '71 Schwinn SS, etc.
Mentioned: 132 Post(s)
Tagged: 0 Thread(s)
Quoted: 1568 Post(s)
Liked 1,306 Times
in
869 Posts
There are no replacement hoods available for Shimano 9s STI levers from pre-2004 or so.
I use a squirt of rubbing alcohol to remove hoods using a twisting action.
They are getting stretched when they are half-way off, so I try to be quick about it.
Twisting action gets them fully on after getting them started on the handlebar end, that's the tricky part.
I use a squirt of rubbing alcohol to remove hoods using a twisting action.
They are getting stretched when they are half-way off, so I try to be quick about it.
Twisting action gets them fully on after getting them started on the handlebar end, that's the tricky part.
#6
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,558
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 493 Post(s)
Liked 1,666 Times
in
762 Posts
I've only removed these after taking the shifter off the bars. Indoors warmth and soapy water help.
#7
Senior Member
Thread Starter
Join Date: Mar 2016
Location: North of Boston
Posts: 905
Bikes: 1973 Schwinn Sports Tourer plus a " few" more :)
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 212 Post(s)
Liked 202 Times
in
148 Posts
All great ideas!!!!!
Thank you.....I might just take the shifter off and clean.......
Or leave on and clean.
Believe it or not, I found a pair of replacement hoods !!!!!
Used of course. But they cleaned up nice with dawn dish detergent and warm water.
Just using my hands to clean.
did this for about 5 minutes. Rinsed and let dry.
I know getting hoods off and on are a PIA...!!!!
Sometimes if the hoods are completely shot, AND I have a new set to replace them with, I just cut them off.
Being these hoods are VERY RARE to get, I want to try to salvage them
I'll keep all posted
Meanwhile....keep all the ideas coming
Greatly appreciated!!!!
Thank you.....I might just take the shifter off and clean.......
Or leave on and clean.
Believe it or not, I found a pair of replacement hoods !!!!!
Used of course. But they cleaned up nice with dawn dish detergent and warm water.
Just using my hands to clean.
did this for about 5 minutes. Rinsed and let dry.
I know getting hoods off and on are a PIA...!!!!
Sometimes if the hoods are completely shot, AND I have a new set to replace them with, I just cut them off.
Being these hoods are VERY RARE to get, I want to try to salvage them
I'll keep all posted
Meanwhile....keep all the ideas coming
Greatly appreciated!!!!
#8
Senior Member
Join Date: Apr 2009
Posts: 999
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 404 Post(s)
Liked 595 Times
in
308 Posts
With the levers off of the bars a squirt of silicone spray under the hood will not only let them come right off but is actually good for them. Unlike the other crap that has been suggested.
JMO of course. Use whatever turns you on.
JMO of course. Use whatever turns you on.
#9
Thread derailleur
Join Date: Mar 2004
Location: Glendora, CA
Posts: 668
Bikes: Croll '94 & Cannondale Supersix '15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 378 Post(s)
Liked 478 Times
in
275 Posts
Worth noting that, with 9-speed of that era, it's easier to pull brake cables than derailleur cables.
At least in terms of reinstalling and adjusting. So detaching the levers method requires brake cable detachment.
Using silicone works for removal, but you want to completely dry it off the shifter body prior to installing the replacements.
Otherwise, the new hoods could squirm around too much.
At least in terms of reinstalling and adjusting. So detaching the levers method requires brake cable detachment.
Using silicone works for removal, but you want to completely dry it off the shifter body prior to installing the replacements.
Otherwise, the new hoods could squirm around too much.
#10
Senior Member
Thread Starter
Join Date: Mar 2016
Location: North of Boston
Posts: 905
Bikes: 1973 Schwinn Sports Tourer plus a " few" more :)
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 212 Post(s)
Liked 202 Times
in
148 Posts
Hoods are OFF !!!
Heated them up slightly with a heat light.
Then working from the bottom "peeled" them back.
Took about 1 -2 minutes each hood.
Soaking and washed with dawn dish soap using just my hands mainly......used a sponge for about 5 seconds.
they are in fair to good condition.
As long as they are not sticky.......fine with me.
After drying I'll check. Have the baby powder on hand just in case
Thanks again for all the help !!!
Much appreciated
Happy and Safe New Year to all!!!!
Heated them up slightly with a heat light.
Then working from the bottom "peeled" them back.
Took about 1 -2 minutes each hood.
Soaking and washed with dawn dish soap using just my hands mainly......used a sponge for about 5 seconds.
they are in fair to good condition.
As long as they are not sticky.......fine with me.
After drying I'll check. Have the baby powder on hand just in case
Thanks again for all the help !!!
Much appreciated
Happy and Safe New Year to all!!!!
#11
Full Member
Indeed, but some of us are lucky enough to have NOS ones hanging around. Mine happen to be unopened in the original package. I should probably sell them, don't have any bikes with 9-speed STI's, only 8 and 10.