The Longest Chainstays out there
#1
Banned.
Thread Starter
The Longest Chainstays out there
I was wondering about whether or not there are bikes which have unusually long chainstays, whether they be road or mountain, modern or classic. And, that these long chainstay blessed frames are not cargo bikes (mid, longtail etc) or tandems. What have you seen in the "extra acreage" chainstay department? (Unusually long, means freakishly)
#2
Full Member
?
gm
gm
#4
Bikes are okay, I guess.
Join Date: Jan 2015
Location: Richmond, Virginia
Posts: 6,980
Bikes: Waterford Paramount Touring, Raleigh Sports 3-speeds in M23 & L23, Schwinn Cimarron oddball build, Marin Palisades Trail dropbar conversion, Nishiki Cresta GT
Liked 2,484 Times
in
1,577 Posts
Many early MTBs had what looked like absurdly long chainstays; Miyatas, DiamondBacks, etc. had 4+ inches behind the seat tube.
#5
Senior Member
Here's my '84 Stumpjumper, chainstay length about 475mm with the pictured wheel position:
Likes For HTupolev:
Likes For nick_a:
Likes For nick_a:
#8
Why?
#9
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,700
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Liked 4,537 Times
in
2,522 Posts
I was wondering about whether or not there are bikes which have unusually long chainstays, whether they be road or mountain, modern or classic. And, that these long chainstay blessed frames are not cargo bikes (mid, longtail etc) or tandems. What have you seen in the "extra acreage" chainstay department? (Unusually long, means freakishly)
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#10
Senior Member
If you want to see really long chainstays, look at stuff that Grant Petersen designs. A lot of his models go over 500mm.
Likes For urbanknight:
Likes For theblackbullet:
#14
Palmer
Join Date: Mar 2007
Location: Parts Unknown
Posts: 8,781
Bikes: Mike Melton custom, Alex Moulton AM, Dahon Curl
Liked 1,975 Times
in
1,135 Posts
There was a cat here on BF (maybe still here?) who was building custom touring bikes with reeeeeaaaaaallly long rear centers, with wheelbases pretty nearly as long as a donkeyback tandem. This was to place heavy touring loads nearer the C/G of the total machine + rider in the wheelbase. Can't remember the name of the bikes...anyone? Bueller? Bueller? Anyway, panniers are 'cargo', if you will, and the OP said 'not cargo bikes'.
Easy Racers might have long chainstays, depending.
Truebikes have long chainstays but don't look like they do.
Easy Racers might have long chainstays, depending.
Truebikes have long chainstays but don't look like they do.
#15
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 25,043
Bikes: Several, mostly not name brands.
Liked 3,675 Times
in
2,077 Posts
The eary-80s Trek 720 has 47cm chainstays, to maximize heel clearance when touring with panniers.
#17
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,339
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Liked 1,871 Times
in
1,062 Posts
I've showed these photos before. 20 inch chainstays. Here it is in road bike configuration right after I got it from the frame builder:
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
And here it is in touring mode with Panaracer Pasela 26x1.75
20200723_141115 by Richard Mozzarella, on Flickr
And Gravel with Compass 559x58 tubeless on a Velocity Cliffhanger wheels I built to replace the non-tubeless capable Dyad/Aeroheat rims previously equipped.
98080187-21F5-4D43-B49B-C324DEFB4946 by Richard Mozzarella, on Flickr
Then there is the good ol' 1974 Schwinn Varsity with 18 inch chainstays. I extended them another 2, among other changes:
20190218_050706 by Richard Mozzarella, on Flickr
Who has the longest stays? Check your local frame builder. It might be hard to go beyond 20 inches. But, 20 inches (508mm) is certainly doable. I'd recommend to anyone, if you haven't experienced a longer than average rear-center, at least give it a try. You might like it.
I tend to think of a long rear center like the tail feathers on an arrow. It knocks down the twitchy, "racy" feel at a given trail, & replaces it with a feeling of surgical precision. The bike effortlessly tracks a straight line.
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
And here it is in touring mode with Panaracer Pasela 26x1.75
20200723_141115 by Richard Mozzarella, on Flickr
And Gravel with Compass 559x58 tubeless on a Velocity Cliffhanger wheels I built to replace the non-tubeless capable Dyad/Aeroheat rims previously equipped.
98080187-21F5-4D43-B49B-C324DEFB4946 by Richard Mozzarella, on Flickr
Then there is the good ol' 1974 Schwinn Varsity with 18 inch chainstays. I extended them another 2, among other changes:
20190218_050706 by Richard Mozzarella, on Flickr
Who has the longest stays? Check your local frame builder. It might be hard to go beyond 20 inches. But, 20 inches (508mm) is certainly doable. I'd recommend to anyone, if you haven't experienced a longer than average rear-center, at least give it a try. You might like it.
I tend to think of a long rear center like the tail feathers on an arrow. It knocks down the twitchy, "racy" feel at a given trail, & replaces it with a feeling of surgical precision. The bike effortlessly tracks a straight line.
Last edited by base2; 07-04-22 at 11:14 AM.
Likes For base2:
#19
JohnDThompson I built my touring bike with 47cm chain. stays along with horizontal drop outs that add another 1cm when the wheel is moved back in the slot. One unexpected outcome is the amount of flex in the bottom end of the bike when under pressure. I used the same tubing on another frame and the same main triangle, but with 42.5cm chain stays and the bottom of the bike does not flex anywhere near what the touring bike flexes. Both frames ride well, however the touring rig is more lazy-boy than bicycle. Super duper comfortable and can fit the largest of panniers out back and have heel clearance with my size 13 feet!
#20
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,867
Bikes: RSO E-tire dropper fixie brifter
Liked 3,302 Times
in
2,096 Posts
I've showed these photos before. 20 inch chainstays. Here it is in road bike configuration right after I got it from the frame builder:
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
And here it is in touring mode with Panaracer Pasela 26x1.75
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
And here it is in touring mode with Panaracer Pasela 26x1.75
__________________
-YMMV
-YMMV
#21
Advanced Slacker
Join Date: Feb 2017
Posts: 6,252
Bikes: Soma Fog Cutter, Surly Wednesday, Canfielld Tilt
Liked 2,571 Times
in
1,451 Posts
Surly Big Dummy is pretty long.
#22
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 9,156
Bikes: Fuji Touring, Novara Randonee
Liked 2,158 Times
in
1,328 Posts
I've showed these photos before. 20 inch chainstays. Here it is in road bike configuration right after I got it from the frame builder:
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
Rodriguez High Roller UTB Disc, custom geometry by Richard Mozzarella, on Flickr
#23
Senior Member
#24
Banned.
Thread Starter
Thanks to all for the suggestions! The Big Dummy would classify as a cargo bike though. The custom Rodriguez is remarkable. I doubt it seems that I'll be able to find an older bike with the type of chainstay lengths I was looking for. It seems a frame with a 20"er for chainstays would be good. I'd like to be able to position the rear load on a bike more directly over the rear axle or between the two axles as much as possible. Right now the load is tugging on the seatstays because too much is hanging off the back end which I think has resulted in the failure of my last frame and most recent snapping off of a pannier barrel brazeon on the current frame (I think it was destned for failure though, based on the meagre brazing tack-on it received at the factory). I don't have a car anymore and have been getting around like this for about 15 years now. The type of setup has been very useful and utilitarian - and economical. I'll post a picture of my go-to bike shortly.
#25
I am potato.
Join Date: Jun 2015
Location: Pacific Northwest
Posts: 3,339
Bikes: Only precision built, custom high performance elitist machines of the highest caliber. 🍆
Liked 1,871 Times
in
1,062 Posts
pdlamb himespau I think it only uses 1 chain. Or IIRC at the most 1 chain + a link depending on the gearing on account of there being no derailleur to feed. Some chains are 112 links, others come in 116 links. With the perfectly straight chain line, it has been so long since I've bought a chain that I honestly don't remember the particulars. I'm well aware that most of what makes an e-bike chain an e-bike chain is they often are as long as 136 links. But I know I don't need one that long.
In gravel/camping mode I install a 21 or 23 cog to the a 50 tooth chainring & that can get to be pretty long. When switching I need to install an inner plate & another master link. In road mode, I run a 16 or 17 cog adjust the eccentric & remove the effective full link. This is necessitated by the adjustment range of the eccentric.
prairiepedaler have you looked here? I think the Platapus is sexy. But, they have an Atlantis & one or two others in stock.
In gravel/camping mode I install a 21 or 23 cog to the a 50 tooth chainring & that can get to be pretty long. When switching I need to install an inner plate & another master link. In road mode, I run a 16 or 17 cog adjust the eccentric & remove the effective full link. This is necessitated by the adjustment range of the eccentric.
prairiepedaler have you looked here? I think the Platapus is sexy. But, they have an Atlantis & one or two others in stock.
Last edited by base2; 07-05-22 at 10:49 AM.