Hand position on drop bars?
#1
Senior Member
Thread Starter
Hand position on drop bars?
Just curious. What is the hand position you use/like the most on you drop bar road bike, Hoods? Bends?Tops? Drops? I ask because I notice that on different bikes I prefer different positions despite the bike similar bike fit on all three bikes. On my Domane I favor the bends and tops. On my Mazama touring bike I prefer the hoods. On my Spcialized Lanster single speed I also like the hoods. the only time I am on the drops is to fight a headwind or when I come down a steep, fast hill.
#2
Banned
specifics?
Are the set ups quite different from each other? or all the same?
Being in such a variety, what is the style of drop bar bend in each case..?
.
Being in such a variety, what is the style of drop bar bend in each case..?
.
Last edited by fietsbob; 11-21-18 at 12:04 PM.
#3
52psi
Join Date: Aug 2013
Location: Tucson, AZ
Posts: 4,017
Bikes: Schwinn Volare ('78); Raleigh Competition GS ('79)
Liked 803 Times
in
392 Posts
Drops, almost exclusively. I used to be ramps/hoods 90% of the time, but evolved away from that over the last year or two.
__________________
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
A race bike in any era is a highly personal choice that at its "best" balances the requirements of fit, weight, handling, durability and cost tempered by the willingness to toss it and oneself down the pavement at considerable speed. ~Bandera
#4
Mother Nature's Son
Join Date: Mar 2016
Location: Sussex County, Delaware
Posts: 3,158
Bikes: 2014 Orbea Avant MD30, 2004 Airborne Zeppelin TI, 2003 Lemond Poprad, 2001 Lemond Tourmalet, 2014? Soma Smoothie
Liked 1,472 Times
in
838 Posts
I spend much more time on the hoods than any other area. I do change positions frequently and use pretty much the whole handlebar, just not as much as the hoods. I also change position in each one of the specific areas, forward or backward, side to side, straightening, bending the arms and just sort of rolling my shoulder hands or wrists. I have spinal and shoulder issues and even just making small adjustments helps to minimize the stress/fatigue factor. Along that same line I use a more relaxed set up on my bikes. Like bikes themselves, what you like and are comfortable with are very personal. I think for most people that is an ongoing adaptation from bike to bike.
#5
vespertine member
Join Date: Jul 2013
Location: Land of Angora, Turkey
Posts: 2,476
Bikes: Yes
Liked 220 Times
in
163 Posts
I'm about 50/50, hoods and drops between three bikes with three different fits - a road bike that's about perfect, a single speed that's a bit more aggressive (smaller frame and lower stack), and a gravel bike that's a bit less aggressive.
I probably end up using the drops just a bit more on the road bike. I'm more likely to climb in the drops on the road bike or gravel bike than the single speed, and more likely to hit rollers in the drops on asphalt vs. gravel. Always drops for descending, unless on ice.
Tops? Never.
I probably end up using the drops just a bit more on the road bike. I'm more likely to climb in the drops on the road bike or gravel bike than the single speed, and more likely to hit rollers in the drops on asphalt vs. gravel. Always drops for descending, unless on ice.
Tops? Never.
#6
vespertine member
Join Date: Jul 2013
Location: Land of Angora, Turkey
Posts: 2,476
Bikes: Yes
Liked 220 Times
in
163 Posts
I always feel weird in a paceline when I notice that I'm in the drops and everyone else is on the hoods. For a lot of riding, the drops just seem more comfortable.
#7
Senior Member
Join Date: Oct 2013
Location: Mich
Posts: 7,702
Bikes: RSO E-tire dropper fixie brifter
Liked 3,195 Times
in
2,030 Posts
Drops unless it's a slow ride with no to little activity from other obstacles
__________________
-YMMV
-YMMV
#8
Advocatus Diaboli
Join Date: Feb 2015
Location: Wherever I am
Posts: 8,735
Bikes: Merlin Cyrene, Nashbar steel CX
Liked 1,562 Times
in
1,025 Posts
#9
Junior Member
Hoods almost exclusively...or down on the clip-on aero bars, which is easier on the wrists (but only when safe to do so).
l rode on the drops more with my last bike as it had compact bars...haven't gotten around to buying them for this one yet.
l rode on the drops more with my last bike as it had compact bars...haven't gotten around to buying them for this one yet.
#10
Banned
OP obviously a Roadie , I'm Not.
Several, varies, that's why they were chosen..
Bike touring , has my day long upright ish posture favoring..
Randonneur bend bars,
the last long tour I had a custom fabricated stem ,
combining 2 narrow ones,* to be as wide on the top, as my road bike
(road, Nitto, From an early MB1.. drops parallel, bottoms flare
(bar end shifters)
previous..
(Specialized badged Nitto) set they were narrower... drop flares , bottom parallel
sizing is across the bottom, so a 46 bottom but 38 top..
Now I mostly use trekking bars or straight bars ,
With Ergon Grips/bar end shifters ...
with IGH Drivetrains.. not derailleurs..
* having them come apart was an advantage in packing the bike
in an airline carton, to fly across the Atlantic , to tour , over there..
carry on kids..
....
Bike touring , has my day long upright ish posture favoring..
Randonneur bend bars,
the last long tour I had a custom fabricated stem ,
combining 2 narrow ones,* to be as wide on the top, as my road bike
(road, Nitto, From an early MB1.. drops parallel, bottoms flare
(bar end shifters)
previous..
(Specialized badged Nitto) set they were narrower... drop flares , bottom parallel
sizing is across the bottom, so a 46 bottom but 38 top..
Now I mostly use trekking bars or straight bars ,
With Ergon Grips/bar end shifters ...
with IGH Drivetrains.. not derailleurs..
* having them come apart was an advantage in packing the bike
in an airline carton, to fly across the Atlantic , to tour , over there..
carry on kids..
....
Last edited by fietsbob; 11-21-18 at 01:45 PM.
#11
Callipygian Connoisseur
Hoods 99% of the time.
-Kedosto
-Kedosto
#12
Occam's Rotor
Yes
#14
Senior Member
At a cruising pace I'm usually down grabbing the tips. I like bars with long tips. On one set of bars I actually bought some Control Tech 20mm bar extensions because they were too short.
#15
Senior Member
I see the older road bikes...the bar is higher....the newer compact road bikes...the bar is very low.
So, I think with newer compact geometry, you are forced to ride on the Hood. No way I can bend low enough to hold it in the Drop position on these compact geometry frame.
For this reason, I like the older diamond frame with horizontal top tube...I can get the handlebar quite high.
So, I think with newer compact geometry, you are forced to ride on the Hood. No way I can bend low enough to hold it in the Drop position on these compact geometry frame.
For this reason, I like the older diamond frame with horizontal top tube...I can get the handlebar quite high.
#16
Senior Member
Join Date: Jan 2009
Location: Colorado Springs, CO
Posts: 6,001
Bikes: 2015 Charge Plug, 2007 Dahon Boardwalk, 1997 Nishiki Blazer, 1984 Nishiki International, 2006 Felt F65, 1989 Dahon Getaway V
Liked 1,702 Times
in
840 Posts
I spend much more time on the hoods than any other area. I do change positions frequently and use pretty much the whole handlebar, just not as much as the hoods. I also change position in each one of the specific areas, forward or backward, side to side, straightening, bending the arms and just sort of rolling my shoulder hands or wrists. I have spinal and shoulder issues and even just making small adjustments helps to minimize the stress/fatigue factor. Along that same line I use a more relaxed set up on my bikes. Like bikes themselves, what you like and are comfortable with are very personal. I think for most people that is an ongoing adaptation from bike to bike.
#17
I use them all, and adjust my position regularly on long rides. Often I don't even put my hands on the bars, but rest my forearms on the tops of the bars. This makes me a little more aero, and gives my hands a little break (which is necessary on rides longer than 100 miles). The reason to run road bars is to offer a variety of positions for a variety of riding positions.
#18
Senior Member
Join Date: Jun 2013
Location: location location
Posts: 3,036
Bikes: MBK Super Mirage 1991, CAAD10, Yuba Mundo Lux, and a Cannondale Criterium Single Speed
Liked 297 Times
in
207 Posts
Hoods for “just riding along.” Sometimes on tops if sighting is more important than access to brakes.
Hoods or tops for climbing. Hoods if out of saddle.
Drops for descending. I hit a pothole on a fast downhill on the hoods once and my bars bent down. Very nearly came off. Drops 100% ever since.
Drops or “invisible aero bars” when riding hard on the flat. Sometimes hoods for a change of position.
I have bullhorns on my single speed, and they just aren’t versatile enough.
Hoods or tops for climbing. Hoods if out of saddle.
Drops for descending. I hit a pothole on a fast downhill on the hoods once and my bars bent down. Very nearly came off. Drops 100% ever since.
Drops or “invisible aero bars” when riding hard on the flat. Sometimes hoods for a change of position.
I have bullhorns on my single speed, and they just aren’t versatile enough.
#20
Sunshine
Join Date: Aug 2014
Location: Des Moines, IA
Posts: 16,801
Bikes: '18 class built steel roadbike, '19 Fairlight Secan, '88 Schwinn Premis , Black Mountain Cycles Monstercross V4, '89 Novara Trionfo
Liked 7,741 Times
in
4,302 Posts
I see the older road bikes...the bar is higher....the newer compact road bikes...the bar is very low.
So, I think with newer compact geometry, you are forced to ride on the Hood. No way I can bend low enough to hold it in the Drop position on these compact geometry frame.
For this reason, I like the older diamond frame with horizontal top tube...I can get the handlebar quite high.
So, I think with newer compact geometry, you are forced to ride on the Hood. No way I can bend low enough to hold it in the Drop position on these compact geometry frame.
For this reason, I like the older diamond frame with horizontal top tube...I can get the handlebar quite high.
I ride 63-65 cm road bikes. With traditional horizontal top tube geometry, the stack height is close to the seat post height which is the bike measurement.
the same stack height on a modern frame can be had woth a 58cm seatpost.
#21
Senior Member
For me it depends on the bike.
X4, I'm virtually always in the drops. It feels weird on the hoods as the brake levers are on the downward portion of the bars. When I'm on the hoods I have this uneasy sensation of going over the front of the bike.
Ti Mega tube, I have a set of Cinelli Spinacholi (?). I'm getting to really like these things. In this case I rest my forearms on the top of the bars and I rest my hands on the Spinocholi's.
Carbon Cross, virtually all the time on the hoods.
X4, I'm virtually always in the drops. It feels weird on the hoods as the brake levers are on the downward portion of the bars. When I'm on the hoods I have this uneasy sensation of going over the front of the bike.
Ti Mega tube, I have a set of Cinelli Spinacholi (?). I'm getting to really like these things. In this case I rest my forearms on the top of the bars and I rest my hands on the Spinocholi's.
Carbon Cross, virtually all the time on the hoods.
#22
Senior Member
I generally ride on the Tops, or the 'shoulders' where the top starts to bend forward, or drops if heading into a strong wind. Never on the hoods since my bars are deep drops, and the brake levers are waaaay out front. In fact my old Fuji doesn't even have hoods!
#24
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 14,058
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Liked 4,248 Times
in
2,841 Posts
Generally on the hoods is where I spend most of my days (that or the playground) but since many of my bike use Ergo top section bars I also will spend some time there because it is also comfortable. I am not often in the drops but I am not a flexible person especially these days. If I had any vintage style bars I don't know where I would want to keep my hands, I generally dislike those bars because of the positioning. I know they worked for Merckx but as much as I love Eddy, I am not him and will never even be an iota close to him.