Small common parts that seem to be way overpriced
#1
Senior Member
Thread Starter
Join Date: Jan 2019
Location: Toledo Ohio
Posts: 1,525
Bikes: 1964 Huffy Sportsman, 1972 Fuji Newest, 1973 Schwinn Super Sport (3), 1982 Trek 412, 1983 Trek 700, 1989 Miyata 1000LT, 1991 Bianchi Boardwalk, plus others
Liked 712 Times
in
401 Posts
Small common parts that seem to be way overpriced
As title says, some small parts seem way overpriced to me. Leading off are crank arm dust covers. I guess I didn’t have them in tight enough and lost both nice Shimano ones on my Miyata. Of course even if available, these are perhaps $20 each. Even generic plastic ones are $5. It seems generic metal ones should be $5 considering the universal fit. Brake cable end ferrules also come to mind as they are quite pricey considering the low tech and universal application. Any other rants here?
Likes For sd5782:
#3
Senior Member
Milk and gas and, um, chewing gum!
#4
Senior Member
Join Date: Oct 2013
Location: Highlands Ranch, CO
Posts: 1,221
Bikes: '13 Diamondback Hybrid Commuter, '17 Spec Roubaix Di2, '17 Spec Camber 29'er, '19 CDale Topstone Gravel
Liked 445 Times
in
260 Posts
Agreed. ShimaNO, CampagNOlo, and ScRAM (just made that one up) are all equally annoying and should be done away with.
Last edited by Riveting; 03-01-22 at 04:10 PM.
Likes For Riveting:
#5
Senior Member
One time I told someone a presta adapter was $3 (I know they’re often cheaper) and he said “$3?! I could make that! Just need to get a chunk of brass, cut it, thread both ends, put in an o ring….”
I asked him if he’d make me one for $3.
I asked him if he’d make me one for $3.
Likes For bboy314:
#6
Likes For Polaris OBark:
#7
The little wire retainer clip that slips onto the slot on the disc brake pad retainer bolt. (Also the bolt itself, which is $5.)
#8
Senior Member
"Vintage" parts are likely one of those things that have limited stock, so prices are all over the ballpark.
One thing that happens is that selling individual items incurs a cost. So, the Presta adapter mentioned above, they should be less than $0.50 each if purchased by the hundred, or by the thousand. But, there is a lot of handling that gets priced in when buying one.
One thing that happens is that selling individual items incurs a cost. So, the Presta adapter mentioned above, they should be less than $0.50 each if purchased by the hundred, or by the thousand. But, there is a lot of handling that gets priced in when buying one.
Likes For TiHabanero:
#10
Banned.
Small parts prices are high, and they always have been. Small stuff is what always falls off/gets lost, after all. That's why when I hook somebody up with one out of my stash, or I'm hooked up with one by somebody out of theirs, we both know we're doing each other a solid ![Smilie](images/smilies/smile.gif)
Suck it up - and add some blue Loctite while you're at it!
DD
![Smilie](images/smilies/smile.gif)
Suck it up - and add some blue Loctite while you're at it!
DD
Likes For Drillium Dude:
#11
Banned.
Or this slightly modified version of the same:
![](https://cimg1.ibsrv.net/gimg/bikeforums.net-vbulletin/1600x1268/image_821cdde556a4354bbdf01085f70f1121eecbabe7.png)
DD
![](https://cimg1.ibsrv.net/gimg/bikeforums.net-vbulletin/1600x1268/image_821cdde556a4354bbdf01085f70f1121eecbabe7.png)
DD
Likes For Drillium Dude:
#12
Senior Member
Join Date: Mar 2015
Location: New Zealand
Posts: 1,058
Bikes: Gunnar, Shogun, Concorde, F Moser, Pete Tansley, Rocky Mtn, Diamant, Krapf, Marin, Avanti, Winora, Emmelle, Ken Evans
Liked 419 Times
in
219 Posts
As title says, some small parts seem way overpriced to me. Leading off are crank arm dust covers. I guess I didn’t have them in tight enough and lost both nice Shimano ones on my Miyata. Of course even if available, these are perhaps $20 each. Even generic plastic ones are $5. It seems generic metal ones should be $5 considering the universal fit.
Likes For Soody:
Likes For bboy314:
#15
2k miles from the midwest
Join Date: Feb 2005
Location: Washington
Posts: 1,964
Bikes: ~'75 Colin Laing, '80s Schwinn SuperSport 650b, ex-Backroads ti project...
Liked 932 Times
in
447 Posts
I'll never forget the day, several after leaving a shop job, when I realized I no longer had any shift ferrules. I'd brought home 2 quart-sized Ball jars of bench sweepings when I left.
#17
$5 and up - way up. A piece of plastic the size of a thumbnail made by the millions
![](https://i.ebayimg.com/images/g/dQgAAOSwUhthx0nN/s-l1600.jpg)
#18
Senior Member
One word: Aliexpress.
#19
Are you talking about the Shimano 600 tri-color cranks? If so those crank hole covers are NOT interchangeable with the universal covers. If you look carefully you'll notice that the cover follows the contours of the crank. One side is higher than the other side. It's not just a simple round cap!
#20
Junior Member
Plastic Cygolite Adapter...$16![Frown](images/smilies/frown.gif)
![Frown](images/smilies/frown.gif)
![](https://cimg9.ibsrv.net/gimg/bikeforums.net-vbulletin/757x562/adapter_152af992341b64842a1dd516a96b7a309a8932b9.jpg)
#21
buy my bikes
Join Date: Jun 2014
Location: Michigan
Posts: 1,823
Bikes: my very own customized GUNNAR CrossHairs
Liked 453 Times
in
254 Posts
I was thinking of starting a kind of loose-screws sales thread.
I got washers and and spacers and what not that I had to buy in bulk-ish.
I think this kind of goes to the OP.
I got washers and and spacers and what not that I had to buy in bulk-ish.
I think this kind of goes to the OP.
#22
Senior Member
Join Date: Mar 2021
Location: Beaverton, OR
Posts: 1,476
Bikes: You had me at rusty and Italian!!
Liked 1,100 Times
in
571 Posts
If it’s old, small and I can’t find it anywhere else I pay the money and don’t look back.
I agree with comments about crank dust caps. They’re ridiculously expensive for something some see as unnecessary. I think they look clean but I’m peculiar. Very peculiar….
I agree with comments about crank dust caps. They’re ridiculously expensive for something some see as unnecessary. I think they look clean but I’m peculiar. Very peculiar….
#23
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,741
Bikes: '70s - '80s Campagnolo
Liked 6,657 Times
in
3,295 Posts
#24
Senior Member
I'm having trouble picturing where the crank dustcaps go:
![](https://cimg2.ibsrv.net/gimg/bikeforums.net-vbulletin/640x360/rrachainset1_84b9bb3755798bab623e7ef4fb7e416e9283a161.jpg)
Likes For nlerner:
#25
Banned.
C'mon - some of you don't know what crank dust covers actually do? For real?
A clue: they most definitely serve a purpose, depending on the type of crank/BB - for example, you don't need them on cottered cranks.
"A dustcap may also refer, on a bicycle, to the crankarm bolt cover. It is usually a piece of metal or plastic that, on the crankarm, is snapped or screwed into the threaded counterbore, which houses the bolt that holds the crankarm to its axle, the bottom bracket spindle. The dustcap serves to protect the threads (on the inside of the counterbore), which are used with a crankarm puller to remove the crankarm from the spindle. It is also possible for the crank arm to squirm on the bottom bracket spindle, causing the crankarm nut/bolt to become loose, leading to the nut/bolt working its way out of the bottom bracket spindle. The dust cap limits the amount of dangerous loosening that can occur."
DD
A clue: they most definitely serve a purpose, depending on the type of crank/BB - for example, you don't need them on cottered cranks.
"A dustcap may also refer, on a bicycle, to the crankarm bolt cover. It is usually a piece of metal or plastic that, on the crankarm, is snapped or screwed into the threaded counterbore, which houses the bolt that holds the crankarm to its axle, the bottom bracket spindle. The dustcap serves to protect the threads (on the inside of the counterbore), which are used with a crankarm puller to remove the crankarm from the spindle. It is also possible for the crank arm to squirm on the bottom bracket spindle, causing the crankarm nut/bolt to become loose, leading to the nut/bolt working its way out of the bottom bracket spindle. The dust cap limits the amount of dangerous loosening that can occur."
DD
Last edited by Drillium Dude; 03-01-22 at 09:19 PM.