PSA, Inflate tire to 80% psi
#1
Junior Member
Thread Starter
PSA, Inflate tire to 80% psi
For longevity and "I know what psi my tires need to be...." I meant 80% of max psi. Refers to car tires as well..
4 of
4 of
Last edited by rc5781; 05-18-23 at 08:45 PM.
#3
Senior Member
Join Date: Oct 2014
Location: Portland, OR
Posts: 12,969
Bikes: (2) ti TiCycles, 2007 w/ triple and 2011 fixed, 1979 Peter Mooney, ~1983 Trek 420 now fixed and ~1973 Raleigh Carlton Competition gravel grinder
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 4854 Post(s)
Liked 3,994 Times
in
2,593 Posts
Huh? So front and rear tires should get the same pressure. Wet and dry don't matter? Neither does rider weight? Or does one swap tire sizes ride to ride to meet these conditions and stay at that magic 80%?
If you were going to go by a magic percent, a given percentage of "squish", ie sidewall deflection would probably be better. (I'"d stick to my 5 psi difference front and rear. I like enough surplus air in front to cover hitting that pothole braking hard with all my weight on the front wheel. A moment where I would rather not suddenly blow the tire or wreck the rim.
If you were going to go by a magic percent, a given percentage of "squish", ie sidewall deflection would probably be better. (I'"d stick to my 5 psi difference front and rear. I like enough surplus air in front to cover hitting that pothole braking hard with all my weight on the front wheel. A moment where I would rather not suddenly blow the tire or wreck the rim.
Likes For 79pmooney:
#4
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,918
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 107 Post(s)
Tagged: 0 Thread(s)
Quoted: 2367 Post(s)
Liked 2,891 Times
in
1,577 Posts
for cars you follow the manufacturers recommendations other wise you risk loss of control and handling and increase risk of blowouts with under inflation
for bikes there are any number of calculators that will give you a range based on weight, tire size and type there is not standard for all much less some vague 80%
Please don't post uninformed, dangerous crap when you don't know what you are talking about
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Last edited by squirtdad; 05-18-23 at 10:25 PM.
Likes For squirtdad:
#5
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,638
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3873 Post(s)
Liked 2,574 Times
in
1,581 Posts
Likes For ThermionicScott:
#6
Really Old Senior Member
Likes For Bill Kapaun:
#7
Senior Member
Join Date: Jul 2005
Posts: 6,017
Mentioned: 26 Post(s)
Tagged: 0 Thread(s)
Quoted: 2512 Post(s)
Liked 751 Times
in
531 Posts
We can agree that the o.p. misses the mark, but ... I have been riding since 1967 and I have never tried to maintain a differential between f/r. I have never used my weight to compute optimum psi. I do NOT take precipitation or lack of it into consideration. At zero dark thirty when I am heading out on the outbound commute there is only one thing I want to know: do the tires have air? A squeeze of the sidewalls (can't thumb the tire: fenders) tells me all I need to know. I've been doing it this way for too long to stop now.
Likes For Leisesturm:
#8
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,783
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 3762 Post(s)
Liked 5,709 Times
in
2,881 Posts
Folks can do stuff wrong for years and suffer no ill effects. One of the satisfactions of a hobby is taking the time to learn and do things right.
Likes For shelbyfv:
Likes For soyabean:
#10
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,958
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 990 Post(s)
Liked 884 Times
in
529 Posts
Thanks
#11
Junior Member
Thread Starter
I just stretched an assumption to bicycle tires.
Likes For rc5781:
#12
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,958
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 990 Post(s)
Liked 884 Times
in
529 Posts
Lee Abel
30+ Yr Senior Master Automotive TechnicianAuthor has 1.9K answers and 1.9M answer views3yAs a 30+ yr auto tech AND front end specialist I have long held factory MINIMUM air specs are just that. MINIMUM.
I was given advice many years ago and it really holds true in what I witnessed over the years. If you take your tires max inflation and use 80% of that your going to get much better results in my opinion.
I like running small to medium cars at 40 psi. If it's auv/cuv try 42.
If it's too stiff/rough try dropping to 38 psi.
But try to keep the 80% , your tires will hold up much better.
I watched a lady with older car that came with actual 32–35 psi tires, door said like 28. With 51 psi tires that half flat.
She went to 40 and loves her new tires.
35.2K views
View upvotes
30+ Yr Senior Master Automotive TechnicianAuthor has 1.9K answers and 1.9M answer views3yAs a 30+ yr auto tech AND front end specialist I have long held factory MINIMUM air specs are just that. MINIMUM.
I was given advice many years ago and it really holds true in what I witnessed over the years. If you take your tires max inflation and use 80% of that your going to get much better results in my opinion.
I like running small to medium cars at 40 psi. If it's auv/cuv try 42.
If it's too stiff/rough try dropping to 38 psi.
But try to keep the 80% , your tires will hold up much better.
I watched a lady with older car that came with actual 32–35 psi tires, door said like 28. With 51 psi tires that half flat.
She went to 40 and loves her new tires.
35.2K views
View upvotes
#13
Expired Member
Join Date: Jun 2007
Location: TN
Posts: 11,783
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 3762 Post(s)
Liked 5,709 Times
in
2,881 Posts
That's a stretch for sure. Here's a better idea Silca PSI Chart
Likes For shelbyfv:
#14
Senior Member
Join Date: Apr 2011
Posts: 7,301
Mentioned: 43 Post(s)
Tagged: 0 Thread(s)
Quoted: 4554 Post(s)
Liked 1,697 Times
in
1,113 Posts
https://www.quora.com/What-is-the-re...0to%2045%20psi.
I just stretched an assumption to bicycle tires.
I just stretched an assumption to bicycle tires.
Why would you extrapolate from some dude that posted on Quora like it is coming from a useful reference?
#15
Junior Member
Thread Starter
The advice in that link is stupid. Most passenger cars use a pressure closer to 30psi, not 40. 40 will increase gas mileage at the sacrifice of breaking and turning traction.
Why would you extrapolate from some dude that posted on Quora like it is coming from a useful reference?
Why would you extrapolate from some dude that posted on Quora like it is coming from a useful reference?
#16
Senior Member
Join Date: Apr 2011
Posts: 7,301
Mentioned: 43 Post(s)
Tagged: 0 Thread(s)
Quoted: 4554 Post(s)
Liked 1,697 Times
in
1,113 Posts
How long have you been driving around in a car with the tires 30% overinflated? Have you noticed the additional centerline wear? How's the emergency handling?
#17
Senior Member
Join Date: Mar 2022
Location: Missoula MT
Posts: 1,785
Bikes: Handsome xoxo, Serotta atx, Canyon Endurace CF8
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 906 Post(s)
Liked 1,949 Times
in
863 Posts
here is what a large reputable tire manufacturer says for their tires.
https://www.toyotires.com/media/pxcj...s_20200723.pdf
https://www.toyotires.com/media/pxcj...s_20200723.pdf
#18
Senior Member
Join Date: Mar 2022
Location: Missoula MT
Posts: 1,785
Bikes: Handsome xoxo, Serotta atx, Canyon Endurace CF8
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 906 Post(s)
Liked 1,949 Times
in
863 Posts
That's a stretch for sure. Here's a better idea Silca PSI Chart
or this one. curiously enough the if I average the RH soft and firm I get really close to the Silca psi..
Likes For jadmt:
#19
Full Member
I must admit that I'm getting a little nostalgic for the simplicity of the days when thin was in (are there still 19mm tires?) and max pressure was a must to avoid pinch flats. Not missing the pinch flats though.
#20
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,921
Bikes: 1989 Cinelli Supercorsa
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 3596 Post(s)
Liked 3,016 Times
in
1,824 Posts
I imagine if I tried I might be able to find some 19mm tires. I wish they were more readily available, and slicks would be even better. I still run my tires at the max (140 psi), and stating so usually triggers a large portion of BF folks.
#21
Senior Member
Join Date: Apr 2011
Posts: 7,301
Mentioned: 43 Post(s)
Tagged: 0 Thread(s)
Quoted: 4554 Post(s)
Liked 1,697 Times
in
1,113 Posts
Wouldn't solid rubber tires be a better choice?
Likes For Kontact:
#23
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,921
Bikes: 1989 Cinelli Supercorsa
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 3596 Post(s)
Liked 3,016 Times
in
1,824 Posts
#24
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,921
Bikes: 1989 Cinelli Supercorsa
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 3596 Post(s)
Liked 3,016 Times
in
1,824 Posts
#25
ignominious poltroon
Join Date: Jan 2022
Posts: 4,138
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 2280 Post(s)
Liked 3,503 Times
in
1,839 Posts
I miss the road surfaces that permitted one to ride with tires less than 38mm wide.
Likes For Polaris OBark: