What have you been wrenching on lately?
#7826
Cantilever believer
And I figure it's my bike and I'm spending my time on it, so I don't want it to be all that boring or mundane. It makes me happy, in spite of the unavoidable "quality workout" it provides. And if other riders are quite happy with black matte graphics on black matte frames with black matte wheels and black matte tires, that's OK too.
But this bike is never truly silent, in that Wald baskets are notorious for singing the song of their tribe, fortunately not all that loudly unless I'm hauling loose metal parts in them. And there was a big difference between that level of sound and what I was hearing - and feeling - from the bottom bracket yesterday. All fixed now.
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
#7827
Crawlin' up, flyin' down
Join Date: Jan 2006
Location: Democratic Peoples' Republic of Berkeley
Posts: 5,911
Bikes: 1967 Paramount; 1982-ish Ron Cooper; 1978 Eisentraut "A"; two mid-1960s Cinelli Speciale Corsas; and others in various stages of non-rideability.
Liked 2,931 Times
in
1,229 Posts
Wisdom is achieved when one can be both loud and silent at the same time.
And I figure it's my bike and I'm spending my time on it, so I don't want it to be all that boring or mundane. It makes me happy, in spite of the unavoidable "quality workout" it provides. And if other riders are quite happy with black matte graphics on black matte frames with black matte wheels and black matte tires, that's OK too.
But this bike is never truly silent, in that Wald baskets are notorious for singing the song of their tribe, fortunately not all that loudly unless I'm hauling loose metal parts in them. And there was a big difference between that level of sound and what I was hearing - and feeling - from the bottom bracket yesterday. All fixed now.
And I figure it's my bike and I'm spending my time on it, so I don't want it to be all that boring or mundane. It makes me happy, in spite of the unavoidable "quality workout" it provides. And if other riders are quite happy with black matte graphics on black matte frames with black matte wheels and black matte tires, that's OK too.
But this bike is never truly silent, in that Wald baskets are notorious for singing the song of their tribe, fortunately not all that loudly unless I'm hauling loose metal parts in them. And there was a big difference between that level of sound and what I was hearing - and feeling - from the bottom bracket yesterday. All fixed now.
I personally would not go the "explosion in a paint factory" route, nor would I go the black-on-black route. But if forced to choose one or the other, I'd take your color palette in a heartbeat.
Tailwinds, and keep the rubber side down.
__________________
"I'm in shape -- round is a shape." Andy Rooney
"I'm in shape -- round is a shape." Andy Rooney
#7828
Senior Member
Join Date: Mar 2024
Location: San Diego
Posts: 1,221
Bikes: Columbine, Paramount Track Bike, Colnago Super, Santana Tandems (1995 & 2007), Gary Fisher Piranha, Trek Wahoo, Bianchi Track Bike, a couple of Honda mountain bikes
Liked 440 Times
in
271 Posts
Building up a bike for my daughter with parts I’ve collected and an eBay frame. I was going to put on a Shimano drivetrain, but after all the trouble I’ve had with our tandem and its Shimano system, I decided to use a SRAM Eagle 12-speed combo (900 hub, XDR Driver, 10-30 cassette and trigger shifter).
I’m incredibly impressed with the engineering attention to detail, the nice touches, how easily it went together and how well it works. The engineers that designed this setup must also work on bikes!
Ran into a snag with the front disc brake, so it’s not rideable yet (I’m now a convert to Centerlock discs), but I love ❤️ Ho it shifts on the stand. Reminds me of paddle shifters on my jalopy!
I’m incredibly impressed with the engineering attention to detail, the nice touches, how easily it went together and how well it works. The engineers that designed this setup must also work on bikes!
Ran into a snag with the front disc brake, so it’s not rideable yet (I’m now a convert to Centerlock discs), but I love ❤️ Ho it shifts on the stand. Reminds me of paddle shifters on my jalopy!
__________________
Cheers, Mike
-Stupid hurts....ride safe
Cheers, Mike
-Stupid hurts....ride safe
Likes For PromptCritical:
#7829
Senior Member
Join Date: Mar 2007
Location: SF Bay Area, East bay
Posts: 7,979
Bikes: Miyata 618 GT, Marinoni, Kestral 200, Soma double cross 2002 Trek 5200, KHS Flite, Koga Miyata, Schwinn Spitfire 5, Mondia Special, Univega Alpina, Miyata team Ti, Santa Cruz Highball, Waterford rs11
Liked 3,059 Times
in
1,392 Posts
I was just funnin' with ya. "It makes me happy." That's all the justification needed, regardless of what I or anyone else might think.
I personally would not go the "explosion in a paint factory" route, nor would I go the black-on-black route. But if forced to choose one or the other, I'd take your color palette in a heartbeat.
Tailwinds, and keep the rubber side down.
I personally would not go the "explosion in a paint factory" route, nor would I go the black-on-black route. But if forced to choose one or the other, I'd take your color palette in a heartbeat.
Tailwinds, and keep the rubber side down.
#7830
Crawlin' up, flyin' down
Join Date: Jan 2006
Location: Democratic Peoples' Republic of Berkeley
Posts: 5,911
Bikes: 1967 Paramount; 1982-ish Ron Cooper; 1978 Eisentraut "A"; two mid-1960s Cinelli Speciale Corsas; and others in various stages of non-rideability.
Liked 2,931 Times
in
1,229 Posts
[QUOTE=curbtender;23224264]That would fit in nicely in your hometown. A couple of ladies bring by their burning man bikes to get the fur out of the axles, lol.[/QUOTE]
Nah. Too hum-drum.
Nah. Too hum-drum.
__________________
"I'm in shape -- round is a shape." Andy Rooney
"I'm in shape -- round is a shape." Andy Rooney
Likes For bikingshearer:
#7831
The Rock Hopper gets a redux for the Mrs. 66.
#7832
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,732
Bikes: Bicycles? Yup.
Liked 2,074 Times
in
873 Posts
The Crescent 318 brazing guinea pig.
And that yellow package behind the vise, that's a pair of plastic gloves from a Chinese restaurant. When they gave them to everyone at my MIL'S 93rd birthday dinner, I couldn't believe they were handing out condoms, and said so, just to amuse myself. Sure as **** nobody else laughed. 😜 😜 😜
And that yellow package behind the vise, that's a pair of plastic gloves from a Chinese restaurant. When they gave them to everyone at my MIL'S 93rd birthday dinner, I couldn't believe they were handing out condoms, and said so, just to amuse myself. Sure as **** nobody else laughed. 😜 😜 😜
Last edited by BTinNYC; 04-26-24 at 02:45 PM.
Likes For BTinNYC:
Likes For BTinNYC:
#7834
Francophile
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,576
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Liked 680 Times
in
333 Posts
Been putting together a 1970s Claud Butler 531 frame using parts taken from my stash. Front wheel has a SON dynamo and rear has a wide range Suntour Ultra 6 freewheel. Bar cons, Mafac Racer brakes with C Record levers (which work very nicely together), Specialites TA triple with a 26-38-42 combination, Vélo Orange fenders. The bike will be my vélotaf/wet weather ride.
i set it up at first with the brake cables running along the bars, but the rear brake cable stops were clearly designed for cables running out the top of the levers. So I'll find a hole punch and open up the top of the hoods to reroute the brake cables. (Edit to say I found the punch, and the cables have been rerouted. Much better!)
i set it up at first with the brake cables running along the bars, but the rear brake cable stops were clearly designed for cables running out the top of the levers. So I'll find a hole punch and open up the top of the hoods to reroute the brake cables. (Edit to say I found the punch, and the cables have been rerouted. Much better!)
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
Last edited by Aubergine; 04-26-24 at 10:06 PM.
#7835
Senior Member
Join Date: Aug 2010
Location: Utah
Posts: 9,013
Bikes: Paletti,Pinarello Monviso,Duell Vienna,Giordana XL Super,Lemond Maillot Juane.& custom,PDG Paramount,Fuji Opus III,Davidson Impulse,Pashley Guv'nor,Evans,Fishlips,Y-Foil,Softride, Tetra Pro, CAAD8 Optimo,
Liked 6,250 Times
in
2,009 Posts
Spent too much time today swapping parts between an old C4 Air One vintage C.F. bike and the new to me Sancineto. Made a stupid mistake in the process and decided to just do a rare for me bike tear down. So stripped the Air One completely except for the headset and binder bolt and listed it locally for sale. I was going to move it along anyone, just not like this.
And while it's not really wrenching I did drop off the old C.F. fork for my Colnago CT1 to a local guy for some minor repair.
And while it's not really wrenching I did drop off the old C.F. fork for my Colnago CT1 to a local guy for some minor repair.
__________________
Steel is real...and comfy.
Steel is real...and comfy.
Likes For dualresponse:
#7837
Cantilever believer
I'd received a pair of lowrider front racks that I thought might be perfect for my Bike Friday. This being Friday, I test-fitted them only to find they were just a bit mismatched for the 20" fork. So I reinstalled the older Blackburn lowriders with my blacksmithed center support, and then remembered that I'd been planning to see if some 20" fenders that I'd purchased for the bike years ago might fit. No better time than a cooler-than-usual Friday, and after fabricating a few unique brackets (and finding out one set of stays were missing), they were finally in place and looking decent.
(the "oversize nail clippers" leaning against the workstand were needed to trim the fender stays.)
(the "oversize nail clippers" leaning against the workstand were needed to trim the fender stays.)
#7838
Steel is real
Join Date: Mar 2013
Location: Not far from Paris
Posts: 2,460
Bikes: 1992Giant Tourer,1992MeridaAlbon,1996Scapin,1998KonaKilaueua,1993Peugeot Prestige,1991RaleighTeamZ(to be upgraded),1998 Jamis Dragon,1992CTWallis(to be built),1998VettaTeam,1995Coppi(to be built),1993Grandis(to be built)
Liked 1,274 Times
in
848 Posts
Eying carefully on ebay future MTB spare parts to be purchased , then in june get the gary fisher and then the trek fuel100 assembled. After that from July 2024 until mid 2025 assembly of all road bikes
#7839
Senior Member
Join Date: Aug 2010
Location: Utah
Posts: 9,013
Bikes: Paletti,Pinarello Monviso,Duell Vienna,Giordana XL Super,Lemond Maillot Juane.& custom,PDG Paramount,Fuji Opus III,Davidson Impulse,Pashley Guv'nor,Evans,Fishlips,Y-Foil,Softride, Tetra Pro, CAAD8 Optimo,
Liked 6,250 Times
in
2,009 Posts
This afternoon was a disassembly of the old Dura Ace headset on the Holdsworth. The grease reminded me more of green peanut butter than grease. Once I got everything all cleaned up I got rid of the caged bearings and rebuilt it with a bunch of loose bearings with fresh grease. It feels so much better now. This was done in anticipation of converting this back to a proper drop bar road bike setup.
__________________
Steel is real...and comfy.
Steel is real...and comfy.
#7840
1991 PBP Anciens
Join Date: Nov 2009
Location: Elburn, Illannoy
Posts: 724
Bikes: 1954 Robin Hood, 1964 Dunelt, 1968 Raleigh Superbe, 1969 Robin Hood, 197? Gitane, 1973 Raleigh SuperCourse, 1981 Miyata 710, 1990 Miyata 600GT, 2007 Rivendell Bleriot
Liked 496 Times
in
189 Posts
The 90 year old Craftsman 918 lathe had some work done on it over the past week. Sometime in its past, the counter shaft drive pulley was replaced. Because the correct pulley probably wasn't available, or a previous owner made do with what they had(How I was raised), mods were made. Those mods consisted of going without the grease seals and retainers on the left side of the counter shaft. I learned this after pumping grease into the shaft, kicking on the power, and instantly having grease goblins on the white wall behind the lathe, on my shirt, and in my face. Missed my mouth. Just.
The heavy felt grease seals are available as re-pops. The retainers...nope. I hit on the "Hey, I have a lathe. I can make those" thing. After a little thought and Outhouse Engineering's' motto of 'measure once and hope for the best', I hit on modifying engine freeze plugs to work as retainers. It looked good on paper.
First issue was that the new hires at the local NAPA are useless. They can't look up anything without a make/model/year/# of cylinders/with or without AC. I went to the local Auto Zone instead and the old guy behind the counter just asked "what size and how many". I grabbed four at 1 5/8" because I screw up often.
The first two attempts ended up on the 'Experience Pile'. I did not take into account that the backside of the plugs were convex. That made them too thick and messed up the belt alignment. The third attempt worked out and I was able to do the job using a single freeze plug. First I faced the back flat. That gave me a pilot hole that I could bore to the correct ID. Then I used a cut off tool and cut the ring off the back of the plug back. Success.
Both seal retainers on either side of the bearing race. The thing with the bolt in it.
The bolt on the pulley keeps the ring with the felt seal in place on the left side. The Hi-Low range selector/knob/whatzit/thingamajig covers the right side seal when in High range.
I ran the lathe at high speed for a couple of minutes and no more grease goblins flying around.
The heavy felt grease seals are available as re-pops. The retainers...nope. I hit on the "Hey, I have a lathe. I can make those" thing. After a little thought and Outhouse Engineering's' motto of 'measure once and hope for the best', I hit on modifying engine freeze plugs to work as retainers. It looked good on paper.
First issue was that the new hires at the local NAPA are useless. They can't look up anything without a make/model/year/# of cylinders/with or without AC. I went to the local Auto Zone instead and the old guy behind the counter just asked "what size and how many". I grabbed four at 1 5/8" because I screw up often.
The first two attempts ended up on the 'Experience Pile'. I did not take into account that the backside of the plugs were convex. That made them too thick and messed up the belt alignment. The third attempt worked out and I was able to do the job using a single freeze plug. First I faced the back flat. That gave me a pilot hole that I could bore to the correct ID. Then I used a cut off tool and cut the ring off the back of the plug back. Success.
Both seal retainers on either side of the bearing race. The thing with the bolt in it.
The bolt on the pulley keeps the ring with the felt seal in place on the left side. The Hi-Low range selector/knob/whatzit/thingamajig covers the right side seal when in High range.
I ran the lathe at high speed for a couple of minutes and no more grease goblins flying around.
Likes For bikamper:
#7841
Cantilever believer
Rode 26 miles this morning with the club, had a nice nap, and now getting back to tube patching. Already patched over a dozen, and tested a bunch more.
Only 10 more bins to go through...
Only 10 more bins to go through...
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
#7842
Senior Member
Join Date: Nov 2005
Location: NW Ohio
Posts: 3,556
Bikes: 1984 Miyata 310, 1986 Schwinn Sierra, 2011 Jamis Quest, 1980 Peugeot TH8 Tandem, 1992 Performance Parabola, 1987 Ross Mt. Hood, 1988 Schwinn LeTour, 1988 Trek 400T, 1981 Fuji S12-S LTD, 197? FW Evans
Liked 1,243 Times
in
605 Posts
First issue was that the new hires at the local NAPA are useless. They can't look up anything without a make/model/year/# of cylinders/with or without AC. I went to the local Auto Zone instead and the old guy behind the counter just asked "what size and how many". I grabbed four at 1 5/8" because I screw up often.
Likes For Pompiere:
#7843
Edumacator
Join Date: Jan 2018
Location: Goose Creek, SC
Posts: 7,570
Bikes: '87 Crestdale, '87 Basso Gap, '92 Rossin Performance EL-OS, 1990 VanTuyl, 1980s Losa, 1985 Trek 670, 1982 AD SLE, 1987 PX10, etc...
Liked 3,596 Times
in
2,259 Posts
Not bike related. Making a throne/reading bench for my princess “niece” (daughter of a work wife). Her name is Lily which the legs spell as a secret if you look at the entire thing from the left of center.
Phases 1 and 2 complete. 3 and 4 to come.
Phases 1 and 2 complete. 3 and 4 to come.
__________________
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
1987 Crest Cannondale, 1987 Basso Gap, 1992 Rossin Performance EL, 1990ish Van Tuyl, 1985 Trek 670, 2003 Pinarello Surprise, 1990ish MBK Atlantique, 1987 Peugeot Competition, 1987 Nishiki Tri-A, 1981 Faggin, 1996 Cannondale M500, 1984 Mercian, 1982 AD SuperLeicht, 1985 Massi (model unknown), 1988 Daccordi Griffe , 1989 Fauxsin MTB, 1981 Ciocc Mockba, 1992 Bianchi Giro, 1977 Colnago Super, 1971 Raleigh International, 1998 Corratec Ap & Dun, 1991 Peugeot Slimestone
Likes For jdawginsc:
#7844
1991 PBP Anciens
Join Date: Nov 2009
Location: Elburn, Illannoy
Posts: 724
Bikes: 1954 Robin Hood, 1964 Dunelt, 1968 Raleigh Superbe, 1969 Robin Hood, 197? Gitane, 1973 Raleigh SuperCourse, 1981 Miyata 710, 1990 Miyata 600GT, 2007 Rivendell Bleriot
Liked 496 Times
in
189 Posts
I ran into that when I needed an alternator for an old tractor. It had been converted to 12 volts by mounting a junkyard alternator to it. There are several different alternators that are popular for this mod because they have the diodes and voltage regulator built in, so there is only one wire to connect to the battery. The tractor came to me that way, so I had no idea what car the alternator came from. Just saying "I need one of these" and handing them the part wasn't good enough. The counter person passed me off to someone with more mechanical experience. First, he scrolled through a lot of microfiche to find one that looked like mine so he could figure out how to hook it to the test machine. The alternator only has one output terminal, how hard can it be? After he confirmed it was junk, I asked how much for a new one and his reply was "What make and model?" Didn't we already cover this? So I said what about the one on the microfiche. It was only $45, so I said to ring it up. The mounting ears were slightly different, but I just needed to move a couple washers to line up the pulley to the drive belt and I was in business.
BTW, my 1948 DeSoto has a Delco 10SI alternator in it, converted to 6 volt positive ground. So nice to have bright headlights.
Likes For bikamper:
#7845
Francophile
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,576
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Liked 680 Times
in
333 Posts
Been putting together a 1970s Claud Butler 531 frame using parts taken from my stash. Front wheel has a SON dynamo and rear has a wide range Suntour Ultra 6 freewheel. Bar cons, Mafac Racer brakes with C Record levers (which work very nicely together), Specialites TA triple with a 26-38-42 combination, Vélo Orange fenders. The bike will be my vélotaf/wet weather ride.
i set it up at first with the brake cables running along the bars, but the rear brake cable stops were clearly designed for cables running out the top of the levers. So I'll find a hole punch and open up the top of the hoods to reroute the brake cables. (Edit to say I found the punch, and the cables have been rerouted. Much better!)
i set it up at first with the brake cables running along the bars, but the rear brake cable stops were clearly designed for cables running out the top of the levers. So I'll find a hole punch and open up the top of the hoods to reroute the brake cables. (Edit to say I found the punch, and the cables have been rerouted. Much better!)
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
Likes For Aubergine:
#7846
1991 PBP Anciens
Join Date: Nov 2009
Location: Elburn, Illannoy
Posts: 724
Bikes: 1954 Robin Hood, 1964 Dunelt, 1968 Raleigh Superbe, 1969 Robin Hood, 197? Gitane, 1973 Raleigh SuperCourse, 1981 Miyata 710, 1990 Miyata 600GT, 2007 Rivendell Bleriot
Liked 496 Times
in
189 Posts
According to my bone doc and my physical therapist, I'm fixing myself much faster and better than expected.
If I behave myself()I can be boot free by the end of the week. To celebrate, I crawled slowly up on the sidecar rig, backed it out of the garage, and rode up and down the street in front of the house just to see if I could shift it. I could. In an act of good judgement, I rode it right back into the garage and shut it down. Good judgement comes from wisdom. Wisdom comes from bad judgement. If I get the okay after my next session, I may try pedaling a bike up and down the driveway.
If I behave myself()I can be boot free by the end of the week. To celebrate, I crawled slowly up on the sidecar rig, backed it out of the garage, and rode up and down the street in front of the house just to see if I could shift it. I could. In an act of good judgement, I rode it right back into the garage and shut it down. Good judgement comes from wisdom. Wisdom comes from bad judgement. If I get the okay after my next session, I may try pedaling a bike up and down the driveway.
Likes For bikamper:
#7847
Full Member
Join Date: Jun 2020
Posts: 471
Bikes: 91 Ritchey Ultra, 1992 Specialized Stumpjumper, 1990 Klein Rascal, 97 Trek OCLV9700, 90 Minnelli Eclipse, 95 Marin Bear Valley SE, 1991 Breezer Lightning Flash 1991 Diamondback Axis 1992 Stumpjumper Comp 1983 Stumpjumper Sport
Liked 706 Times
in
246 Posts
For it’s 30th birthday the Hot got reunited with an original tire set.
#7848
Dirty Heathen
Join Date: Oct 2015
Location: MC-778, 6250 fsw
Posts: 2,277
Bikes: 1997 Cannondale, 1976 Bridgestone, 1998 SoftRide, 1989 Klein, 1989 Black Lightning #0033
Liked 985 Times
in
574 Posts
My 89 Cannondale Criterium returned to the road after two years of hanging in the garage while I formulated the plan and collected components. Pretty much everything needed repair or replacement, including the paint job. Only original parts are the brake calipers, because black single-pivots just look right on this era. Microshift R-10 with 5600 DRs, my favorite Salsa Cowchipper handlebars, Mavic CXP-22s, and the icing on the cake; Specialized Turbo 320 tpi cotton clinchers in 26mm.
#7849
Francophile
Join Date: Nov 2015
Location: Seattle and Reims
Posts: 3,576
Bikes: Peugeot: AO-8 1973, PA-10 1971, PR-10 1973, Sante 1988; Masi Gran Criterium 1975, Stevenson Tourer 1980, Stevenson Criterium 1981, Schwinn Paramount 1972, Rodriguez 2006, Gitane Federal ~1975, Holdsworth Pro, Follis 172 ~1973, Bianchi '62
Liked 680 Times
in
333 Posts
Bike is now almost done. The last fiddly bits - - adjusting the Mafac brake shoes, getting the rear fender set in place, running the dynamo wires - - took more time than the rest of the danged installation. All I need to do now is wrap the bars once I get the tape, and then straighten out the handlebar bag. I'll take a better photo once it is done.
Drive side!
The boring side
__________________
Keeping Seattle’s bike shops in business since 1978
Keeping Seattle’s bike shops in business since 1978
Likes For Aubergine:
#7850
Cantilever believer
"The less expensive side."
Unless you have mirrors in a right-hand-drive country.
Unless you have mirrors in a right-hand-drive country.
__________________
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html
Richard C. Moeur, PE - Phoenix AZ, USA
https://www.richardcmoeur.com/bikestuf.html