Stripped bolt holding aero bar arm rest pad
#1
Senior Member
Thread Starter
Stripped bolt holding aero bar arm rest pad
Hello. I have a carbon aero bar on my triathlon bike that the left side bolt stripped out meaning it does not hold the arm rest pad as it just spins in the hole. Now a few things to bring you up to speed on the situation.
1. The handle bar company is long out of business,
2. The bar is carbon with what looks like a tiny aluminum insert where the bolt fits into the handlebar to hold the arm rest. .
3. Last year the original bolt snapped off inside the hole and I had to take the dremel and slice a thin grove in bar hole and bolt to then extract with tiny screwdriver.
4. I have tried some woven copper wire down the hole and that makes it hold but not even long enough for a full ride.
5. I just left the hardware store trying to see if I could find a way to rectify the issue. The guy there said the bolt was a m5 and the next up was m6 and was much larger, did not fit the carbon pad cup and way larger then the metal insert in the handlebar .
Soooo I would appreciate anyones ideas ..........what can I do ********************?
1. The handle bar company is long out of business,
2. The bar is carbon with what looks like a tiny aluminum insert where the bolt fits into the handlebar to hold the arm rest. .
3. Last year the original bolt snapped off inside the hole and I had to take the dremel and slice a thin grove in bar hole and bolt to then extract with tiny screwdriver.
4. I have tried some woven copper wire down the hole and that makes it hold but not even long enough for a full ride.
5. I just left the hardware store trying to see if I could find a way to rectify the issue. The guy there said the bolt was a m5 and the next up was m6 and was much larger, did not fit the carbon pad cup and way larger then the metal insert in the handlebar .
Soooo I would appreciate anyones ideas ..........what can I do ********************?
Last edited by Ilovemyride; 06-02-22 at 05:14 PM.
#2
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,092
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4207 Post(s)
Liked 3,872 Times
in
2,314 Posts
Try to find retailers who sold these bars and thus might have replacement parts still stashed away. Find a fabricator who works with this kind of stuff for "repairs". If you provide a photo we could better understand the details not described.
Of course the best answer is to get newer stuff. Steering control being pretty high up there on most riders' lists. Andy
Of course the best answer is to get newer stuff. Steering control being pretty high up there on most riders' lists. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
#3
Senior Member
Join Date: Mar 2019
Posts: 1,606
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 581 Post(s)
Liked 921 Times
in
518 Posts
There are a thread-repairing products available:
https://www.henkel-adhesives.com/ca/...e_pc_3967.html
This is the Loctite version, others are available.
If you go this route be sure to follow instructions closely.
I wouldn't recommend this for any 'structural' application (fixing the holes on the part of clip on aero bars that clamp the main bars, for instance, would be a bad idea), but for arm pads that are only ever pushed down it will likely work fine.
https://www.henkel-adhesives.com/ca/...e_pc_3967.html
This is the Loctite version, others are available.
If you go this route be sure to follow instructions closely.
I wouldn't recommend this for any 'structural' application (fixing the holes on the part of clip on aero bars that clamp the main bars, for instance, would be a bad idea), but for arm pads that are only ever pushed down it will likely work fine.
#5
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
It seems there is enough area around that hole to install an M5 Helicoil to restore the original hole size.
Likes For HillRider:
#7
Senior Member
Thread Starter
On further inspection it appears to be a metal piece atop the bars that must be glued on under the paint. So maybe just a tap to clean the threads would do it, or you suggest drilling and gluing in new threads , ie ,a helicoil ?
#8
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,674
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,061 Times
in
745 Posts
Videos on how to install. how to install a rivnut without a tool - Search (bing.com)
Last edited by Crankycrank; 06-03-22 at 07:10 PM.
#9
Senior Member
Thread Starter
Ok , so I finally thought I got all the parts and tools together to do the job. I drilled then I used the threads tool. After I turned in the coil and used something heavy to knock off the tang and thought I was done. What I noticed that I thought was odd was the bolt it is maybe 3 quarters inch long but the helicoil spring in the kit is just a few mm in length, is that normal ? Anyway I tightened in the bolt with aero bar arm rest and went to test it laying my arm in and within seconds it just wobbled lose !!! I am sooo annoyed ! I tried to tighten it twice and it just spun, ugghhh. What happened ????
#10
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,674
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,061 Times
in
745 Posts
What I noticed that I thought was odd was the bolt it is maybe 3 quarters inch long but the helicoil spring in the kit is just a few mm in length, is that normal ? Anyway I tightened in the bolt with aero bar arm rest and went to test it laying my arm in and within seconds it just wobbled lose !!! I am sooo annoyed ! I tried to tighten it twice and it just spun, ugghhh. What happened ????
#11
Senior Member
Thread Starter
Yes it all came in a kit. I did notice the thing I was slowly turning in to create ridges or threads stopped going down and it just kept turning, ugh.
#12
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,806
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1944 Post(s)
Liked 2,164 Times
in
1,323 Posts
I’m in the same camp as Andrew R Stewart.
There is a certain speed, while maneuvering over less than ideal road conditions, at which point the bars coming loose can cause a catastrophic accident.
Maybe not initially, but if you make a temporary fix that you believe is a permanent fix, bad things can happen.
John
There is a certain speed, while maneuvering over less than ideal road conditions, at which point the bars coming loose can cause a catastrophic accident.
Maybe not initially, but if you make a temporary fix that you believe is a permanent fix, bad things can happen.
John
#13
Senior Member
Thread Starter
I appreciate all the help and replies , though John I don't think you are paying attention , this has nothing to do with the handle bars or steering it is a arm rest for a tri bike , you can still ride a tri bike not being in the aero position.
#14
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,806
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1944 Post(s)
Liked 2,164 Times
in
1,323 Posts
I understand it is just the rest.
John
John
#15
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,334
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times
in
108 Posts
I’ll start with pointing out that even just an elbow rest suddenly coming loose at an unexpected time can be disastrous. That said, if you want to accept the risk here are a few thoughts:
1. It sounds like you used too short a Helicoil, and have also stripped that. They do come in multiple lengths, so a longer one may help, but the hole may be too damaged at this point.
2. Time-serts are a much stronger thread repair than Helicoil type inserts, and would be a better option. They also come in different lengths and the hole may still be too damaged at this point. It sounds like you may be over tightening the screws based on having failed fasteners in this joint multiple times, though it may just be worn out as well.
3. I’ve had some success in the past by press fitting a custom threaded insert into a properly sized hole. I’m assuming you don’t have the tools to do this, and a pair of handlebars doesn’t justify the machine shop cost to have this done as it would cost more than new bars if they would touch it at all. You may, with an unreasonable amount of labor, be able to file a hex nut down to a threaded insert and bond that in.
4. Opening the hole up in the arm rear frame to allow a larger fastener is possible, but I’m mainly listing that for future readers as tapping it for a Helicoil likely closed the door to this option.
5. I’ve not had particularly good luck with JB Weld and similar products to re-make the thread, but maybe there’s something better out there now.
1. It sounds like you used too short a Helicoil, and have also stripped that. They do come in multiple lengths, so a longer one may help, but the hole may be too damaged at this point.
2. Time-serts are a much stronger thread repair than Helicoil type inserts, and would be a better option. They also come in different lengths and the hole may still be too damaged at this point. It sounds like you may be over tightening the screws based on having failed fasteners in this joint multiple times, though it may just be worn out as well.
3. I’ve had some success in the past by press fitting a custom threaded insert into a properly sized hole. I’m assuming you don’t have the tools to do this, and a pair of handlebars doesn’t justify the machine shop cost to have this done as it would cost more than new bars if they would touch it at all. You may, with an unreasonable amount of labor, be able to file a hex nut down to a threaded insert and bond that in.
4. Opening the hole up in the arm rear frame to allow a larger fastener is possible, but I’m mainly listing that for future readers as tapping it for a Helicoil likely closed the door to this option.
5. I’ve not had particularly good luck with JB Weld and similar products to re-make the thread, but maybe there’s something better out there now.
Likes For jccaclimber:
#16
Go Ride!
Join Date: May 2019
Location: Minnesota—55346
Posts: 268
Bikes: Klein Quantum Pro, Klein Attitude, Azuki SS, Merckx AXM, Klein Quantum Race, Klein Quantum
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 109 Post(s)
Liked 155 Times
in
87 Posts
now that you see you have that much metal around the bolt hole, what if you go back to your original idea of tapping it out for an m6? (Just drill the pad so the wider bolt goes thru and use lots of oil and work slowly when taping out that aluminum.)
One more thought—from looking at the pics—is there room to move the pads (on both sides) forward half an inch by drilling/tapping all new holes? Seems there is room in front of the current hole but not clear on how far the metal base/plate extends.
One more thought—from looking at the pics—is there room to move the pads (on both sides) forward half an inch by drilling/tapping all new holes? Seems there is room in front of the current hole but not clear on how far the metal base/plate extends.
Last edited by Sonofamechanic; 06-18-22 at 08:17 AM.
#17
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,674
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 838 Post(s)
Liked 1,061 Times
in
745 Posts
Last edited by Crankycrank; 06-18-22 at 08:39 AM.
#18
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,599
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 427 Post(s)
Liked 700 Times
in
436 Posts
Could a nut be epoxied in the hole and an appropriate sized bolt used? If possible you could buy a hardened nut and bolt from the hardware store.
Likes For Crankycrank:
#20
Senior Member
Thread Starter
How about a rivet ? I have a rivet gun at my storage . I wonder if that would hold through all the vibrations on my usual 50 mile loops ?
#21
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,092
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4207 Post(s)
Liked 3,872 Times
in
2,314 Posts
"this has nothing to do with the handle bars or steering it is a arm rest" the OP in post 13
THIS is why I shake my head at many threads and posts here. How one keeps the front wheel pointing where it needs to go to stay under the bike's CG is EXTREEMLY important. To suggest that one doesn't need to be able to steer the bike when in the aero position is just stupid and very ignorant. For this reason I am out of this thread. Andy (who wonders where some get their ideas from)
THIS is why I shake my head at many threads and posts here. How one keeps the front wheel pointing where it needs to go to stay under the bike's CG is EXTREEMLY important. To suggest that one doesn't need to be able to steer the bike when in the aero position is just stupid and very ignorant. For this reason I am out of this thread. Andy (who wonders where some get their ideas from)
__________________
AndrewRStewart
AndrewRStewart
#22
Senior Member
Thread Starter
I guess you (Andrew) are too busy giving your unhelpful 2 cents to forum participants that really could not care less . A solution is what is necessary not your unnecessary nasty stupid remarks. And you aren't paying attention either , you just wanting to spout nasty stupid stuff is my guess, you get off on it. No need to respond because it will be boring, but if you take the time and look at the fellow ( 70sSanO ) who wrote the comment he jumped to the WRONG conclusion that what my question for help was something holding the handlebars to the bike and agreeing with you ( Andrew ) for some ******** reason. Ya should read it all before responding with rude ripping comments , better yet never comment unless its toward a solution .
#23
Go Ride!
Join Date: May 2019
Location: Minnesota—55346
Posts: 268
Bikes: Klein Quantum Pro, Klein Attitude, Azuki SS, Merckx AXM, Klein Quantum Race, Klein Quantum
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 109 Post(s)
Liked 155 Times
in
87 Posts
Actually Andrew makes a good point and we are all actually in agreement with him in principle…sometimes we just get a bit carried away trying to figure out a cheap solution. In reality it makes far more sense to spend the $ on a new/working handlebar. Its like compromising on a fork….you just don’t do that. Period.
#24
Senior Member
Thread Starter
I am seeing this forum is made up of brainless zombies that can not think for themselves or maybe just bots .
I come here probably like most just asking for friendly advice. I don't claim to know everything like some people giving not needed comments.
MY HANDLEBARS retail valve when new 795.00 .... so no .
I come here probably like most just asking for friendly advice. I don't claim to know everything like some people giving not needed comments.
MY HANDLEBARS retail valve when new 795.00 .... so no .