Fitting of a 7 speed cassette
#1
Newbie
Thread Starter
Join Date: Feb 2013
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Fitting of a 7 speed cassette
I have added a couple of spacers but I am not sure if the last chain ring is too proud.
I have not tightened beyond finger tight.
Does this picture look Ok?
I have not tightened beyond finger tight.
Does this picture look Ok?
#2
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
It's hard to know by looking. What hub do you have?
EDIT: If it were my wheel with an unknown hub, I'd use just enough spacer so that the outer cog has a slight "rock" against the rest of the cassette when the lockring is loose, but the whole cassette feels like one unit once there's some torque on the lockring.
EDIT: If it were my wheel with an unknown hub, I'd use just enough spacer so that the outer cog has a slight "rock" against the rest of the cassette when the lockring is loose, but the whole cassette feels like one unit once there's some torque on the lockring.
__________________
RUSA #7498
Originally Posted by noglider
People in this forum are not typical.
Last edited by ThermionicScott; 02-01-13 at 12:18 PM.
#3
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,727
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,590 Times
in
1,436 Posts
The lockring compresses the cassette against the back shoulder of the freehub body to make everything tight, For that to happen the cassette has to overhang the outside of the body, so the lockring presses on it without bottoming against the FH body.
It's that simple. If you're at all familiar with how threadless headsets are tightened by the top cap, you'll see that these are similar in concept.
So remove the lockring, and compress the cassette with your fingers. If you can bring it flush with the freehub's front edge, you need a spacer, If it still overhangs by a millimeter or so you don't.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#4
Really Old Senior Member
#8
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,727
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,590 Times
in
1,436 Posts
If necessary add enough spacer to the back to have the front overhang by 1-2mm.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#9
Senior Member
Join Date: Aug 2009
Posts: 1,820
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 504 Post(s)
Liked 636 Times
in
376 Posts
I did this last year on a shimano wheel. It was last minute for a ride with my bike, horrified some roadies with the grinder 126mm spark show. The advise above is good, I'll just add that with some cassettes, the rivets or bolts that hold it together will deform the spacers and cause shifting issues when tightened, if this is the case, just remove them, spark show optional.
#10
Senior Member
If it helps, I found and bought my 4.5mm spacer on ebay!
#11
Newbie
Thread Starter
Join Date: Feb 2013
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Many thanks for all the advice. I took the hint to engage brain which for reference resulted in 3 spacers of about 4mm in total.
Thank you.
Thank you.
Thread
Thread Starter
Forum
Replies
Last Post
Metis
Bicycle Mechanics
11
07-10-17 07:05 AM
gearhead82
Bicycle Mechanics
3
07-15-14 11:04 AM