Is anyone looking for a lacing jig?
#1
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Is anyone looking for a lacing jig?
Hey all, I don't post here much as i would like to since I have my own shop and a 9-5 that I work at. On that I would like to do more work with wheelbuilds and as we all know, time is money. I'm looking to create a lacing jig based off of the now defunct Noble Wheels lacing jig at a cheaper pricepoint with some more additions and improvements over the Noble design,
I think my biggest question is "Who else is interested?" Would this be a one-off project for me or would this be an item that can be sold? I have a bunch of other items in the pipeline of additive manufacturing/CNC machining.
Thanks a lot in advance all!
I think my biggest question is "Who else is interested?" Would this be a one-off project for me or would this be an item that can be sold? I have a bunch of other items in the pipeline of additive manufacturing/CNC machining.
Thanks a lot in advance all!
Likes For eddiepliers2:
#2
Full Member
Join Date: Aug 2007
Location: near Detroit
Posts: 304
Bikes: a few..
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 148 Times
in
96 Posts
Hey all, I don't post here much as i would like to since I have my own shop and a 9-5 that I work at. On that I would like to do more work with wheelbuilds and as we all know, time is money. I'm looking to create a lacing jig based off of the now defunct Noble Wheels lacing jig at a cheaper pricepoint with some more additions and improvements over the Noble design,
I think my biggest question is "Who else is interested?" Would this be a one-off project for me or would this be an item that can be sold? I have a bunch of other items in the pipeline of additive manufacturing/CNC machining.
Thanks a lot in advance all!
I think my biggest question is "Who else is interested?" Would this be a one-off project for me or would this be an item that can be sold? I have a bunch of other items in the pipeline of additive manufacturing/CNC machining.
Thanks a lot in advance all!
#3
...
Join Date: Oct 2021
Location: Whitestone and Rensselaerville, New York
Posts: 1,538
Bikes: Bicycles? Yup.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 488 Post(s)
Liked 1,623 Times
in
750 Posts
If I counted 'wheels built per week', instead of per year, I'd definitely get a jig, even at $450. It would really speed the process, but I doubt us enthusiastic amateurs is your market.
A Paceline post with similar idea:
https://forums.thepaceline.net/showthread.php?t=235811
A Paceline post with similar idea:
https://forums.thepaceline.net/showthread.php?t=235811
#4
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,124
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 946 Post(s)
Liked 663 Times
in
375 Posts
I built my own lacing jig which I find very useful for building with internal nipples, straight pull spokes and rims with no nipple access holes.
Most of the building I do these days fall into one of those categories.
For standard builds with J bend spokes and standard nipples I find lacing without the jig to be just as fast and convenient.
Most of the building I do these days fall into one of those categories.
For standard builds with J bend spokes and standard nipples I find lacing without the jig to be just as fast and convenient.
Likes For Dan Burkhart:
#6
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,878
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5874 Post(s)
Liked 2,723 Times
in
1,520 Posts
It would need meaningful features that seriously save time, plus be dirt cheap.
FWIW anyone can improvise something with roughly the same functionality as the $450 unit you referenced with a spindle and 3 soup cans.
For my part, it would be counterproductive because I lace fastest with the wheel vertical.
FWIW anyone can improvise something with roughly the same functionality as the $450 unit you referenced with a spindle and 3 soup cans.
For my part, it would be counterproductive because I lace fastest with the wheel vertical.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#7
Senior member
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,124
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 946 Post(s)
Liked 663 Times
in
375 Posts
Agree with this for lacing with J bend spokes and standard nipples but as I posted above, for building with internal nipples, straight pull spokes, rims with no nipple access holes or when nipple washers are necessary a jig is indispensable.
#8
Senior Member
No!
My guess is that it would not be worthwhile to pay hundreds of $ for an individual who laces wheels only for himself/herself and occasionally for a friend or two who are bicycling enthusiasts. That money would be better utilized for buying higher quality components.
My guess is that it would not be worthwhile to pay hundreds of $ for an individual who laces wheels only for himself/herself and occasionally for a friend or two who are bicycling enthusiasts. That money would be better utilized for buying higher quality components.
Likes For Alan K:
#9
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,878
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5874 Post(s)
Liked 2,723 Times
in
1,520 Posts
In any case, anyone who builds enough wheels to justify shelling out dough for a jig, has enough experience to decide for himself.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#10
Newbie
Thread Starter
Join Date: Nov 2022
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
It would need meaningful features that seriously save time, plus be dirt cheap.
FWIW anyone can improvise something with roughly the same functionality as the $450 unit you referenced with a spindle and 3 soup cans.
For my part, it would be counterproductive because I lace fastest with the wheel vertical.
FWIW anyone can improvise something with roughly the same functionality as the $450 unit you referenced with a spindle and 3 soup cans.
For my part, it would be counterproductive because I lace fastest with the wheel vertical.
I built my own lacing jig which I find very useful for building with internal nipples, straight pull spokes and rims with no nipple access holes.
Most of the building I do these days fall into one of those categories.
For standard builds with J bend spokes and standard nipples I find lacing without the jig to be just as fast and convenient.
Most of the building I do these days fall into one of those categories.
For standard builds with J bend spokes and standard nipples I find lacing without the jig to be just as fast and convenient.
That's the thing, I usually build about 2/3 sets a month, so would I benefit in saving time? I think so, but then there would be another item I would do a deep dive to fix another problem..
#11
Senior Member
Join Date: Aug 2009
Posts: 1,857
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 515 Post(s)
Liked 669 Times
in
394 Posts
Yeah, back in the 80s I worked with a guy at a bike shop in LI who had previously built wheels for Schwinn full time, the owners would keep us 2 on for the winter, just to keep us happy for the season, cause it got crazy busy in the spring. He built basic wheels as busy work, and he laced, tensioned and trued them in 15-20 minutes each, while carrying on a conversation, and not rushing at all, he'd lace one set (1/4 the spokes) on one side free hand, then he'd place it on the stand, and lace the rest, then finish it there. I mostly do it all vertical sitting on a stool. Phil at R&A was also very good and efficient.
#12
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,939
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2619 Post(s)
Liked 1,960 Times
in
1,228 Posts
Sounds like a cool stormy winter day in the shop project. I'd guess a woodworker could duplicate the functionality with $100-$150 of parts (plywood has gone up crazy expensive!) with lots of rollers, slots, and wingnuts for adjustability. I don't have any idea what it would cost in metal, just more.
OK, but what about buying one for a shop? Then it becomes a cost-benefit analysis. If a builder could save 20 minutes per wheel lacing @$50/hr, the payback would only take 30 wheels -- sounds pretty reasonable. Unless you're talking about wheelreason's builder, who might only save 5 minutes per wheelset. 100 wheelsets to pay back the cost sounds like expensive speculation. I'm not sure what small bike business could afford a bet like that.
So, OP (eddiepliers2), what's your best guess at how much this improved gadget is going to cost, and how much time will it save an experienced wheel builder? I couldn't find any projections of the latter for the Noble device, which may be why they're not being made any more.
OK, but what about buying one for a shop? Then it becomes a cost-benefit analysis. If a builder could save 20 minutes per wheel lacing @$50/hr, the payback would only take 30 wheels -- sounds pretty reasonable. Unless you're talking about wheelreason's builder, who might only save 5 minutes per wheelset. 100 wheelsets to pay back the cost sounds like expensive speculation. I'm not sure what small bike business could afford a bet like that.
So, OP (eddiepliers2), what's your best guess at how much this improved gadget is going to cost, and how much time will it save an experienced wheel builder? I couldn't find any projections of the latter for the Noble device, which may be why they're not being made any more.
#13
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,878
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5874 Post(s)
Liked 2,723 Times
in
1,520 Posts
FWIW, I divide wheelbuilding into 4 tasks: loading spokes in hub, lacing, pre-tightening, aligning (including setting elbows, dishing, stress relieving, etc.)
Of those, lacing is about the quickest, at about 3-5 minutes. (goes faster when focused, slower when not). That's for typical wheels with J-bend spokes & plain vanilla rims.
So here's the catch 22. Someone building few wheels might save time, but can't justify the cost. someone experienced and efficient, can't save enough time to matter.
Of those, lacing is about the quickest, at about 3-5 minutes. (goes faster when focused, slower when not). That's for typical wheels with J-bend spokes & plain vanilla rims.
So here's the catch 22. Someone building few wheels might save time, but can't justify the cost. someone experienced and efficient, can't save enough time to matter.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#14
Senior Member
Join Date: Oct 2023
Location: New Jersey
Posts: 587
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 381 Post(s)
Liked 284 Times
in
183 Posts
The proverbial tool that the beginner can't afford and the real pro doesn't bother with. As I was thinking about this, I came up with precious few examples where a pro might substitute pure skill for an expensive tool. Usually, a pro passes on a tool because he has even better tools.
#15
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,939
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2619 Post(s)
Liked 1,960 Times
in
1,228 Posts
FWIW, I divide wheelbuilding into 4 tasks: loading spokes in hub, lacing, pre-tightening, aligning (including setting elbows, dishing, stress relieving, etc.)
Of those, lacing is about the quickest, at about 3-5 minutes. (goes faster when focused, slower when not). That's for typical wheels with J-bend spokes & plain vanilla rims.
So here's the catch 22. Someone building few wheels might save time, but can't justify the cost. someone experienced and efficient, can't save enough time to matter.
Of those, lacing is about the quickest, at about 3-5 minutes. (goes faster when focused, slower when not). That's for typical wheels with J-bend spokes & plain vanilla rims.
So here's the catch 22. Someone building few wheels might save time, but can't justify the cost. someone experienced and efficient, can't save enough time to matter.
Thanks for wrapping my thoughts up so neatly (tied up with a bow!).
#16
Senior Member
Join Date: Aug 2009
Posts: 1,857
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 515 Post(s)
Liked 669 Times
in
394 Posts
Another thing from a shop's point of view, if we wanted or needed something like that (or any other type of jig) we'd just make it, We have a lot of tools and know how after all.
#17
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,878
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5874 Post(s)
Liked 2,723 Times
in
1,520 Posts
The proverbial tool that the beginner can't afford and the real pro doesn't bother with. As I was thinking about this, I came up with precious few examples where a pro might substitute pure skill for an expensive tool. Usually, a pro passes on a tool because he has even better tools.
For example, 50+ years ago as I started building more varied wheels, moving away from the std. 36/36 pairs, spoke length calculations became problematic. This was long before the internet, and even before cheap and convenient computers. So, after a few frustrating mis-estimates, I devised my own analog spoke length calculator. I still use it to this day because it's so fast, easy and reliable.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#19
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,468
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2535 Post(s)
Liked 3,016 Times
in
1,717 Posts
The idea is certainly appealing, but as FBinNY's post pointed out above, lacing a wheel, without or without a jig, takes substantially less time than any other phase of wheelbuilding. A slow lacing process might take 4 or even 5 minutes at the most, and a quick lacing job might take 2 or 3 minutes. At most, a lacing jig would save maybe a minute, maybe two. Not worth it unless you're building wheels for a living, if then.
#20
Newbie
Join Date: Mar 2024
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks for the input. I agree that it is difficult to justify based on time saved.
That said, I have a penchant for nice tools and an aversion to money. I realize that I am an edge case, but it will be worth it to me.
All the best!
That said, I have a penchant for nice tools and an aversion to money. I realize that I am an edge case, but it will be worth it to me.
All the best!