Copying Fit From My Old Bike
#1
Senior Member
Thread Starter
Copying Fit From My Old Bike
I built up a Roubaix 2017 Pro frame over the winter. I got a bike fit on my old bike and I'm trying to copy the same measurements onto the new bike. Both bikes have a Specialized Power Expert saddle and I copied length from the hoods to the front of the saddle to 31.5". I have the exact same handlebar height and yet the bikes feel completely different. On my old bike, I have no pressure on my hands and feel super comfortable. On the Roubaix, I feel more pressure on my hands and shoulders. I'm 6'4" and both frames are 61cm. The reach on my old bike is 411 and the Roubaix is 396. I added a 130 stem to the Roubaix to get the same measurement to the end of the stem because the old bike has a 120 stem. The only thing I can figure out is the stack in the Roubaix is longer than my old bike. The stack on the Roubaix is 650 and my old bike is 617. Can someone help me figure out how to compensate for the difference in stack?
#2
just another gosling
Join Date: Feb 2007
Location: Everett, WA
Posts: 19,535
Bikes: CoMo Speedster 2003, Trek 5200, CAAD 9, Fred 2004
Mentioned: 115 Post(s)
Tagged: 0 Thread(s)
Quoted: 3889 Post(s)
Liked 1,938 Times
in
1,383 Posts
Do it this way: Start by using a long level (or a short one taped to a straight edge) to measure the horizontal distance between the saddle nose and the center of the bottom bracket on the old bike. Transfer that measurement to the new bike. Then measure saddle to hoods.
__________________
Results matter
Results matter
Likes For Carbonfiberboy:
#3
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,810 Times
in
3,318 Posts
If the seat tube is a different angle from the other, then you may never feel quite the same on it. That's not to say you can't make it just as comfortable.
#4
Senior Member
Thread Starter
I just checked and the seat angle for my original bike is 73 and the Roubaix is 73.5...pretty close. The head angle is exact for both at 74.
#5
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,810 Times
in
3,318 Posts
Are the handlebars the same reach and drop? And if you don't have your STI's at the same position or the bend profile of the handlebar is different, that might be putting you in a slightly different position that alters where you put your butt.
You are riding both and deciding about fit aren't you? Don't just sit on them and think bad of one.
You are riding both and deciding about fit aren't you? Don't just sit on them and think bad of one.
#6
Senior Member
Thread Starter
Update: I measured my bottom bracket to the saddle setback on my old bike and I moved my saddle on my new bike to match the setback. I had the saddle on my new bike all the way back on the rails and it now sets halfway on the rails. I went for a ride and there is noticeably more comfort. Being 6'4", I've always had my saddle back as far as it will go to accommodate my long torso.
#7
Senior Member
Join Date: Jul 2009
Posts: 5,949
Bikes: Colnago, Van Dessel, Factor, Cervelo, Ritchey
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 3952 Post(s)
Liked 7,299 Times
in
2,947 Posts
Do it this way: Start by using a long level (or a short one taped to a straight edge) to measure the horizontal distance between the saddle nose and the center of the bottom bracket on the old bike. Transfer that measurement to the new bike. Then measure saddle to hoods.
Likes For tomato coupe:
#8
Senior Member
Thread Starter
Easier to put the bike in a corner, with the back wheel against one wall. Measure from the wall to the saddle nose, and then from the wall to the bottom bracket, and subtract. Use the floor as a reference for vertical measurements. No fussing with levels or plumb bobs.