21.15mm stem in 22.2mm Steerer Tube. Shim or no shim?
#1
Full Member
Thread Starter
Join Date: Mar 2015
Posts: 320
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 88 Post(s)
Liked 296 Times
in
93 Posts
21.15mm stem in 22.2mm Steerer Tube. Shim or no shim?
Hey, folks! I recently swapped out a threaded 1" fork on a bike, with the new threaded 1" fork having a 22.2mm steerer tube. Unfortunately, the original stem on the bike (and original steerer tube) were 21.15mm, which leaves a very minor amount of room around the original stem once inserted into the new steerer tube. I'd really like to keep the original stem. When inserting the original stem into the new steerer tube, the wedge tightens down normally (apparantly) and everything seems firm with no perceptible flex or anything. I can throw a Coke-can style shim in there to fill the gap, but if everything seems to be fine, do I really need to?
Thanks much in advance!
Joe
Thanks much in advance!
Joe
#2
Senior Member
Join Date: Aug 2009
Posts: 2,395
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1562 Post(s)
Liked 1,734 Times
in
974 Posts
Just get the right sized 22.2 stem. They are so common that there is no reason to make do with an undersized stem.
You don’t want to risk having the stem loosen on you in the middle of a ride.
You don’t want to risk having the stem loosen on you in the middle of a ride.
#3
Senior Member
Join Date: Apr 2016
Posts: 1,236
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 503 Post(s)
Liked 436 Times
in
335 Posts
Hey, folks! I recently swapped out a threaded 1" fork on a bike, with the new threaded 1" fork having a 22.2mm steerer tube. Unfortunately, the original stem on the bike (and original steerer tube) were 21.15mm, which leaves a very minor amount of room around the original stem once inserted into the new steerer tube. I'd really like to keep the original stem. When inserting the original stem into the new steerer tube, the wedge tightens down normally (apparantly) and everything seems firm with no perceptible flex or anything. I can throw a Coke-can style shim in there to fill the gap, but if everything seems to be fine, do I really need to?
Likes For grumpus:
#4
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,585 Times
in
1,433 Posts
It's not absolutely necessary to shim it, since the wedge usually has plenty of travel. Sometimes the wedge runs out of travel before being tight, but that can be fixed with a file.
OTOH you might prefer to shim, because while the wedge braces the bottom, the top is free to rock back and forth.
It's not necessary to shim the full length, just up near the top.
How you shim is up to you, and may depend on how deep the stem is. Also, do not shim the area near the wedge. I'm partial to gummed paper tape, because it's easy to widn to an exact diameter. Once it's assembled, soak oil in, and the oil soaked tape will outlast you.
OTOH you might prefer to shim, because while the wedge braces the bottom, the top is free to rock back and forth.
It's not necessary to shim the full length, just up near the top.
How you shim is up to you, and may depend on how deep the stem is. Also, do not shim the area near the wedge. I'm partial to gummed paper tape, because it's easy to widn to an exact diameter. Once it's assembled, soak oil in, and the oil soaked tape will outlast you.
Last edited by FBinNY; 02-02-24 at 12:27 AM.
#5
Insane Bicycle Mechanic
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,843
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 809 Post(s)
Liked 712 Times
in
380 Posts
Hey, folks! I recently swapped out a threaded 1" fork on a bike, with the new threaded 1" fork having a 22.2mm steerer tube. Unfortunately, the original stem on the bike (and original steerer tube) were 21.15mm, which leaves a very minor amount of room around the original stem once inserted into the new steerer tube.
Joe
Joe
Fortunately, this was a common occurrence years ago so there’s a shim made just for this purpose:
https://www.amazon.com/Wald-905-Stee.../dp/B000A5QDY2
A bike shop that’s been around for a few decades might have these in stock.
__________________
Jeff Wills
Comcast nuked my web page. It will return soon..
Jeff Wills
Comcast nuked my web page. It will return soon..
#7
Garage tetris expert
Join Date: May 2016
Location: Texas Hill Country
Posts: 893
Bikes: A few. Ok, a lot
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 387 Post(s)
Liked 692 Times
in
329 Posts
That’s a 1 millimeter difference in diameter… not “minor”. The handlebars will rock side to side, which can be unpleasant.
Fortunately, this was a common occurrence years ago so there’s a shim made just for this purpose:
https://www.amazon.com/Wald-905-Stee.../dp/B000A5QDY2
A bike shop that’s been around for a few decades might have these in stock.
Fortunately, this was a common occurrence years ago so there’s a shim made just for this purpose:
https://www.amazon.com/Wald-905-Stee.../dp/B000A5QDY2
A bike shop that’s been around for a few decades might have these in stock.
For those like me who prefer an alternative to Amazon: https://www.porkchopbmx.com/wald-905...g-shim-13.html
(cheaper too!)
Likes For panzerwagon: