Bike grease recommendations
#26
Senior Member
Bike grease recommendation? Use it. Regularly, and wherever appropriate.
Seriously: bicycle loads and bearing RPMs are trivial compared to what most greases are designed to withstand. Unless you ride in the Arctic, as others have said above pretty much any high-quality grease should work well enough. (If you regularly ride in extremely harsh winter conditions, you might - and that's might - need a low-temp grease formulated for those conditions during winter riding.)
Two caveats: if you regularly ride where you encounter lots of water (trails crossing streams, deep puddles), maybe consider marine grease (it's more water resistant). And don't put grease where it doesn't belong (freehub and freewheel pawls reputedly don't like thick greases).
Seriously: bicycle loads and bearing RPMs are trivial compared to what most greases are designed to withstand. Unless you ride in the Arctic, as others have said above pretty much any high-quality grease should work well enough. (If you regularly ride in extremely harsh winter conditions, you might - and that's might - need a low-temp grease formulated for those conditions during winter riding.)
Two caveats: if you regularly ride where you encounter lots of water (trails crossing streams, deep puddles), maybe consider marine grease (it's more water resistant). And don't put grease where it doesn't belong (freehub and freewheel pawls reputedly don't like thick greases).
Likes For Hondo6:
#27
Senior Member
Join Date: Oct 2014
Location: Reno nevada
Posts: 788
Bikes: a few that I can't recall
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 347 Post(s)
Liked 302 Times
in
147 Posts
I use Phil Wood because it makes me smell like a Bicycle. Everything makes me smell like either a Boat Trailer or a Tractor.
(not much of an exaggeration)
(not much of an exaggeration)
Likes For icemilkcoffee:
#29
Senior Member
Join Date: Dec 2005
Posts: 17,167
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3814 Post(s)
Liked 6,730 Times
in
2,618 Posts
#30
Senior Member
Join Date: Aug 2009
Posts: 2,408
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1571 Post(s)
Liked 1,743 Times
in
979 Posts
Well I have a tube here that separated in less than a year. And I am in San Jose, ostensibly the same climate as Phil Wood. In fact it even says San Jose, CA on the tube of grease if I recall. You want to exchange your non-separated grease with my separated grease?
#31
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,833
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3538 Post(s)
Liked 2,952 Times
in
1,790 Posts
Well I have a tube here that separated in less than a year. And I am in San Jose, ostensibly the same climate as Phil Wood. In fact it even says San Jose, CA on the tube of grease if I recall. You want to exchange your non-separated grease with my separated grease?
Maybe the modern formulation is different?
#32
Senior Member
I bought a tub of waterproof marine grease in the late 1970's. It was bluish-green but has faded to mostly green but is still transparent.
I still have some but you can see the bottom of the tub.
I still have some but you can see the bottom of the tub.
#33
Junior Member
The Phil Wood grease formulation has definitely changed. It 'stinks' more now. I suspect that sulfur has been added to or increased in the mix.
Likes For Jeff Neese:
#35
Palmer
Join Date: Mar 2007
Location: Parts Unknown
Posts: 8,633
Bikes: Mike Melton custom, Alex Moulton AM, Dahon Curl
Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 1672 Post(s)
Liked 1,832 Times
in
1,064 Posts
What's a good all-purpose grease for parts vs hubs and rims or can I use them interchangeably?
Eeeeeevrybody's got their own thing.
Fuchs Renolit CA-LZ (NLGI 2) for bearings: hubs, BBs, headsets pedals.
Houdini Lock Lube for caliper brake and derailleur pivots.
John Deere Cotton Picker Spindle Grease (NLGI 00) for IGH clockwork.
Don't grease your rims.
#36
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,642
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3897 Post(s)
Liked 6,501 Times
in
3,219 Posts
Likes For SurferRosa:
#39
Senior Member
Join Date: Dec 2005
Posts: 17,167
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3814 Post(s)
Liked 6,730 Times
in
2,618 Posts
Likes For nlerner:
#40
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,642
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3897 Post(s)
Liked 6,501 Times
in
3,219 Posts
Likes For SurferRosa:
#41
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,803
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3594 Post(s)
Liked 3,407 Times
in
1,938 Posts
Automobile wheel bearings operate at higher RPM/load/temperature than bicycle wheel bearings. It works fine in bicycle wheel bearings.
#42
Thread derailleur
Join Date: Mar 2004
Location: Glendora, CA
Posts: 652
Bikes: Croll '94 & Cannondale Supersix '15
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 371 Post(s)
Liked 470 Times
in
269 Posts
Some of that tubed Phil green lube (from the 80's) kicks around my stash somewhere.
Could not find it, but found a new Dura Ace bottom bracket and chain, while looking.
For that, I owe this thread a great deal of gratitude.
Like an earlier poster said, that Rock n Roll red stuff works exceptionally well.
Always strive for slickness, not thickness.
Could not find it, but found a new Dura Ace bottom bracket and chain, while looking.
For that, I owe this thread a great deal of gratitude.
Like an earlier poster said, that Rock n Roll red stuff works exceptionally well.
Always strive for slickness, not thickness.
#44
Senior Member
Join Date: Aug 2006
Location: Land of Cheese
Posts: 1,079
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 112 Post(s)
Liked 213 Times
in
105 Posts
In the early 70's I bought a copy of Eugene Sloane's Complete Book of Bicycling where he recommended Lubriplate 105, so I got a tin from an auto parts store back then.
For the longest time it's been Mobil 1.
Trying out Citgo's Mystik JT6 with 3% moly cuz it was on sale at Farm and Fleet, and Valvoline Palladium, 3% moly.
Or maybe just rendered pork fat.
For the longest time it's been Mobil 1.
Trying out Citgo's Mystik JT6 with 3% moly cuz it was on sale at Farm and Fleet, and Valvoline Palladium, 3% moly.
Or maybe just rendered pork fat.
Likes For streetsurfer:
#46
Senior Member
Likes For P!N20:
#48
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,190
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,313 Times
in
1,119 Posts
I have a freezer full of Blue and Gold bacon and sausage (it's an Oklahoma thing) and a recent diagnosis of cardiac arrhythmia. Now I know what to do with my pork investment.
__________________
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
"It is the unknown around the corner that turns my wheels." -- Heinz Stücke
#49
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,525
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2750 Post(s)
Liked 3,407 Times
in
2,062 Posts
Would you use this in the hubs and bearings as well?
Lets say on a pair of Vintage C-Record Hubs with the oil port what's the recommended grease for that application?
I was surprised nothing came up under the search but the search function for "recommended grease" brings up What did you wrench on today and other hits.
Lets say on a pair of Vintage C-Record Hubs with the oil port what's the recommended grease for that application?
I was surprised nothing came up under the search but the search function for "recommended grease" brings up What did you wrench on today and other hits.
grease site:www.bikeforums.net
#50
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
Would you use this in the hubs and bearings as well?
Lets say on a pair of Vintage C-Record Hubs with the oil port what's the recommended grease for that application?
I was surprised nothing came up under the search but the search function for "recommended grease" brings up What did you wrench on today and other hits.
Lets say on a pair of Vintage C-Record Hubs with the oil port what's the recommended grease for that application?
I was surprised nothing came up under the search but the search function for "recommended grease" brings up What did you wrench on today and other hits.