Bottom Bracket spindle length ?
#1
Junior Member
Thread Starter
Join Date: Jan 2021
Location: Bay Area, CA
Posts: 16
Bikes: 1984 Ritchey converted for touring; 1995 Waterford
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Bottom Bracket spindle length ?
I am looking to replace a 175mm triple crank on a 1985 Ritchey with a new 170mm crank. The original Shimano triple crank was on a bottom bracket with a 121.5mm spindle. A 124mm spindle is recommended for the new crank that I’m looking at. Will the 121.5mm spindle work (2.5mm difference), or should I put in a new BB?
#3
Really Old Senior Member
Not all are symmetrical, so it could right on to NOT!
IF the FDER will move in that much, you "should" be good.
You may have to loosen the cable to allow that much inner travel.
Edit: add
Just meandering- the original crank might not be a "perfect" length, but the best compromise.
IF the FDER will move in that much, you "should" be good.
You may have to loosen the cable to allow that much inner travel.
Edit: add
Just meandering- the original crank might not be a "perfect" length, but the best compromise.
Last edited by Bill Kapaun; 07-21-21 at 08:30 PM.
#4
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,092
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4208 Post(s)
Liked 3,874 Times
in
2,314 Posts
Not mentioned is whether the old crank and new one share the same "end of BB axle to center of the rings" dimension. Of course this isn't listed in any spec list I've ever seen. Chain line is the holy grail by many but ring/frame clearances and (as mentioned) ft der range also come into play. So my answer to the OP is "you'll have to try the best first choice and see how it all agrees with each other". Andy .
__________________
AndrewRStewart
AndrewRStewart
#5
Junior Member
Thread Starter
Join Date: Jan 2021
Location: Bay Area, CA
Posts: 16
Bikes: 1984 Ritchey converted for touring; 1995 Waterford
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Thanks for the advice. I'll give the old BB a try and see how it works -- I guess I can always swap it out if there are problems.
Likes For jceastbay:
#6
Senior Member
Join Date: Feb 2015
Location: Mission Viejo
Posts: 5,806
Bikes: 1986 Cannondale SR400 (Flat bar commuter), 1988 Cannondale Criterium XTR, 1992 Serotta T-Max, 1995 Trek 970
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 1944 Post(s)
Liked 2,164 Times
in
1,323 Posts
In 1985 with a triple. I’m going wil Bill on this one that the BB spindle might be asymetrical; which means there is more spindle on the DS than the NDS. It effectively equals a 123mm, 124mm, 125mm symmetrical BB spindle,
John
John
#7
Senior Member
Join Date: Feb 2017
Location: Northern Shenandoah Valley
Posts: 4,141
Bikes: More bikes than riders
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1446 Post(s)
Liked 762 Times
in
570 Posts
The only other thing I think worth mentioning is watching the crank arms and the chain stays, to be sure the crank arms don't contact the stays (using the shorter-than-recommended spindle). It's only 2.5mm shy of ideal, which is only 1.25mm on each side (assuming symmetry, which can't always be assumed), so you're not likely to have issues here...but it is something to watch as you begin to reassemble the bike.
#8
Senior Member
Join Date: Jul 2014
Posts: 1,490
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 1083 Post(s)
Liked 687 Times
in
441 Posts
It's all about the chainline, which is arguably the most important thing to get correct on a bicycle drivetrain. Different cranksets may give you a different (and incorrect) chainline using an existing spindle. You can test-fit it and see, but you don't go by whether you have problems or not - you go by whether the chainline measurement is in spec. The good thing about test fitting on your existing spindle is you can measure, and then you'll know how much longer or shorter the new one needs to be.