Newbie questions
#1
Newbie
Thread Starter
Newbie questions
While not new to bicycles and bicycling, the C&V category still has a few "mysteries" for me.
One thing I was not at all aware of is whether or not road bikes from mid to late '80s would have had springs on the QR shafts? Mine has none on front or rear wheels, but then I am at least the third owner of the bike, so they might have gotten removed at some point.
Were these standard with quick release wheels at the time?
One thing I was not at all aware of is whether or not road bikes from mid to late '80s would have had springs on the QR shafts? Mine has none on front or rear wheels, but then I am at least the third owner of the bike, so they might have gotten removed at some point.
Were these standard with quick release wheels at the time?
#2
Senior Member
Join Date: Dec 2014
Location: Central Virginia
Posts: 4,780
Bikes: Numerous
Mentioned: 150 Post(s)
Tagged: 0 Thread(s)
Quoted: 1678 Post(s)
Liked 3,098 Times
in
914 Posts
Pretty standard as far as I know but you can get by without 'em.
__________________
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
N = '96 Colnago C40, '04 Wilier Alpe D'Huez, '10 Colnago EPS, '85 Merckx Pro, '89 Merckx Century, '86 Tommasini Professional, '04 Teschner Aero FX Pro, '05 Alan Carbon Cross, '86 De Rosa Professional, '82 Colnago Super, '95 Gios Compact Pro, '95 Carrera Zeus, '84 Basso Gap, ‘89 Cinelli Supercorsa, ‘83 Bianchi Specialissima, ‘VO Randonneur, Ritchey Breakaway Steel, '84 Paletti Super Prestige, Heron Randonneur
Likes For Spaghetti Legs:
#3
Full Member
Join Date: Feb 2013
Location: Worcester, Massachusetts
Posts: 308
Bikes: Fuji Sportif 1.7C, Shogun Metro AT, Jamis Durango SX, Miyata Alumicross, Fuji Special Road Racer, Mongoose ATB, Fuji SST 1.0 Team, Gitane (?), Specialized Rockhopper SS, Univega Gran Turismo, Univega Supra Sport Mixte, Nishiki Tri-A, Diamondback Coil
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 82 Post(s)
Liked 141 Times
in
78 Posts
+1 on not totally needing them; as far as I know they have a centering effect when you put the wheel back on. The QR is supposed to have springs for each end, though. Stay in the C&V zone long enough and you'll build up a whole bin of quick releases.
Likes For PugRider:
#4
Newbie
Thread Starter
Already had a small bag of these conical springs from other projects, so will throw some on now knowing they were even used "back in the day". Thanks!
#5
Newbie
Thread Starter
Next puzzling item ..
What on earth is the little projection off the right seatstay? It was welded on, so probably required some strength. Seems like overkill for a reflector mount, and if for racks or fenders, there should be one on the left side as well.
This particular model seemed aimed more at "everyday" riding vs "racer", so I'm imagining the point of this appendage is more functional.
odd seatstay dealio
What on earth is the little projection off the right seatstay? It was welded on, so probably required some strength. Seems like overkill for a reflector mount, and if for racks or fenders, there should be one on the left side as well.
This particular model seemed aimed more at "everyday" riding vs "racer", so I'm imagining the point of this appendage is more functional.
odd seatstay dealio
#6
Senior Member
Join Date: Aug 2020
Location: Saratoga, CA
Posts: 825
Bikes: 1981 Bianchi Specialissim, 1976 Colnago Super. 1971 Bob Jackson. 2012 Kestrel 4000. 2012 Willier. 2016 Fuji Cross 1.1
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 276 Post(s)
Liked 952 Times
in
389 Posts
The projection is for hanging your chain on when removing the rear wheel.
Likes For SwimmerMike:
#7
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,626
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3888 Post(s)
Liked 6,485 Times
in
3,209 Posts
You can get by without the skewer springs just as you can get by without drinking decent beer.
Likes For SurferRosa:
#8
Newbie
Thread Starter
These must have fallen out of favor later, maybe for the endless pursuit of weight reduction? Checking my steel MTB from ~10 yrs after this bike, and it did not have this.
#9
Senior Member
Join Date: Aug 2010
Location: Wurundjeri Country
Posts: 2,469
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 1079 Post(s)
Liked 1,899 Times
in
931 Posts
I could be wrong, but I think the introduction of slant parallelogram derailleurs kind of rendered chain keepers irrelevant; in that the tension could be relieved by pushing the jockey wheel, rather than taking the chain off the gears.
#10
Happy With My Bikes
Join Date: Sep 2020
Location: Oklahoma
Posts: 2,186
Bikes: Hi-Ten bike boomers, a Trek Domane and some projects
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 884 Post(s)
Liked 2,307 Times
in
1,117 Posts
Likes For Chuck M:
#11
señor miembro
Join Date: Dec 2018
Location: Pac NW
Posts: 6,626
Bikes: '70s - '80s Campagnolo
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 3888 Post(s)
Liked 6,485 Times
in
3,209 Posts
Likes For SurferRosa:
#12
Senior Member
Join Date: Feb 2020
Posts: 2,820
Mentioned: 49 Post(s)
Tagged: 0 Thread(s)
Quoted: 1106 Post(s)
Likes: 0
Liked 1,328 Times
in
784 Posts
Springs are worth having. You can get a bag of stainless ones on that auction site - cheap, though shipping may be dear.
Springs are fiddly things to make, and QR ones are special, a conical helix made of flat strip. They often get mashed or lost, so it was a happy result to find them available. What I'd like is a source for the little springs under the plastic wingnut of Simplex QR nuts. They are getting old enough that the plastic is starting to crack and fall apart, and then they fall off and the spring does too. Replacement wingnuts cast from epoxy are easy enough, but *that* spring is essential.
Springs are fiddly things to make, and QR ones are special, a conical helix made of flat strip. They often get mashed or lost, so it was a happy result to find them available. What I'd like is a source for the little springs under the plastic wingnut of Simplex QR nuts. They are getting old enough that the plastic is starting to crack and fall apart, and then they fall off and the spring does too. Replacement wingnuts cast from epoxy are easy enough, but *that* spring is essential.
#13
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1608 Post(s)
Liked 2,216 Times
in
1,103 Posts
When I purchased the wheels for the De Rosa, I had a discovery about one spring.
The hubs are Record in black with black skewers. I was having some problems with the clamp side of the rear hub.
P1030548 on Flickr
There were two springs stacked! pulled one out of the clamp housing and everything worked well. It was a bit mangle.
P1030726 on Flickr
there primary purpose is to assist in mounting the wheel by spreading the open position enough to clear the DO when mounting. I know, kind of obvious.
The hubs are Record in black with black skewers. I was having some problems with the clamp side of the rear hub.
P1030548 on Flickr
There were two springs stacked! pulled one out of the clamp housing and everything worked well. It was a bit mangle.
P1030726 on Flickr
there primary purpose is to assist in mounting the wheel by spreading the open position enough to clear the DO when mounting. I know, kind of obvious.
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
#14
Newbie
Thread Starter
Anyway, now that I know these springs were used even "back in the day", the wheels have a full set! As others have said, it does have a "complete" feel to it.
And I think I'll fight any OCD-like tendencies to get caught up in whether or not black would be the correct spring color for c1987.
#15
Phyllo-buster
Join Date: Jan 2010
Location: Nova Scotia
Posts: 8,847
Bikes: roadsters, club bikes, fixed and classic
Mentioned: 133 Post(s)
Tagged: 0 Thread(s)
Quoted: 2298 Post(s)
Liked 2,054 Times
in
1,254 Posts
#16
Newbie
Thread Starter
"Chain Hanger
Some bikes have a small brazed-on peg facing inward near the bottom of the right seat stay. This is intended to support the chain when the rear wheel has been removed for some reason. This is, in practice, a pretty useless feature."
I don't know yet. Seemed like it would be handy at least to keep the chainstay a bit cleaner. Will have to try it next time.
Likes For 2wheels2:
#17
Senior Member
Join Date: Aug 2010
Location: Wurundjeri Country
Posts: 2,469
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 1079 Post(s)
Liked 1,899 Times
in
931 Posts
Bring back the Portacatena!
Edit: geez, I just noticed that frame has a chain hanger and portacatena. Talk about belts and braces!
Edit: geez, I just noticed that frame has a chain hanger and portacatena. Talk about belts and braces!
Last edited by P!N20; 07-11-22 at 03:49 AM.
Likes For P!N20:
#18
Senior Member
Join Date: May 2008
Location: Fredericksburg, Va
Posts: 9,579
Bikes: '65 Frejus TDF, '73 Bottecchia Giro d'Italia, '83 Colnago Superissimo, '84 Trek 610, '84 Trek 760, '88 Pinarello Veneto, '88 De Rosa Pro, '89 Pinarello Montello, '94 Burley Duet, 97 Specialized RockHopper, 2010 Langster, Tern Link D8
Mentioned: 73 Post(s)
Tagged: 0 Thread(s)
Quoted: 1608 Post(s)
Liked 2,216 Times
in
1,103 Posts
After getting more curious, I searched and found Sheldon Brown had some info. Seems he would agree on irrelevance of chain hangers ...
"Chain Hanger
Some bikes have a small brazed-on peg facing inward near the bottom of the right seat stay. This is intended to support the chain when the rear wheel has been removed for some reason. This is, in practice, a pretty useless feature."
I don't know yet. Seemed like it would be handy at least to keep the chainstay a bit cleaner. Will have to try it next time.
"Chain Hanger
Some bikes have a small brazed-on peg facing inward near the bottom of the right seat stay. This is intended to support the chain when the rear wheel has been removed for some reason. This is, in practice, a pretty useless feature."
I don't know yet. Seemed like it would be handy at least to keep the chainstay a bit cleaner. Will have to try it next time.
Including the Pinarello Montello
P1050206 on Flickr
__________________
Bikes don't stand alone. They are two tired.
Bikes don't stand alone. They are two tired.
Likes For SJX426:
#19
Senior Member
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 5,790
Bikes: 1989 Cinelli Supercorsa
Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 3511 Post(s)
Liked 2,926 Times
in
1,775 Posts
Likes For smd4:
#20
Senior Member
Join Date: Jun 2021
Posts: 1,683
Bikes: '38 Schwinn New World, ’69 Peugeot PX-10, '72 Peugeot PX-10, ‘7? Valgan, '78 Raleigh Comp GS, ’79 Holdsworth Pro, ’80 Peugeot TH-8 tandem, '87 Trek 400T, ‘7? Raleigh Sports, ‘7? Raleigh Superbe, ‘6? Hercules
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 761 Post(s)
Liked 1,563 Times
in
757 Posts
What I'd like is a source for the little springs under the plastic wingnut of Simplex QR nuts. They are getting old enough that the plastic is starting to crack and fall apart, and then they fall off and the spring does too. Replacement wingnuts cast from epoxy are easy enough, but *that* spring is essential.
#21
ambulatory senior
Join Date: Dec 2016
Location: Peoria Il
Posts: 5,998
Bikes: Austro Daimler modified by Gugie! Raleigh Professional and lots of other bikes.
Mentioned: 76 Post(s)
Tagged: 0 Thread(s)
Quoted: 1955 Post(s)
Liked 3,661 Times
in
1,679 Posts
In my youth a chainhanger was considered a dividing line between cheap and better frames. Of course I'm 65 so take that for what it's worth.