Pickup Bed Bike Rack Options
#1
Member
Thread Starter
Join Date: Aug 2015
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
Pickup Bed Bike Rack Options
Hi, in the market for a new vehicle and a small/mid sized pickup ticks the boxes (most likely a Ridgeline). I know I can put a hitch mount rack on, but am looking at in-bed options.
Seems like a bar with a couple of front fork quick release attachment points is an obvious, straightforward, and reasonably secure answer. Any thoughts on if there's a better solution you've come across or generally any comments on this?
Thanks!
Seems like a bar with a couple of front fork quick release attachment points is an obvious, straightforward, and reasonably secure answer. Any thoughts on if there's a better solution you've come across or generally any comments on this?
Thanks!
#2
Senior Member
The bar with quick release hubs works. Check the below out. I'll be getting a new work truck in January and am gonna try these. They make 2 different kinds for depending on what type of bed rail. https://usa.innoracks.com/
#3
Junior Member
Join Date: Jul 2020
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 33 Post(s)
Likes: 0
Liked 75 Times
in
35 Posts
I rolled my own (with some yakima bits, so I could keep it all keyed the same as everythig else. First photo is the original setup, before I added a through-axle bike to the stable. But the thing works, obviously doesn't secure the through-axle bike. But I can install/remove it from the bed in a couple minutes, and until the truck went into the shop, was just leaving it on. For all of our bikes, I can put two bikes in the back with the Van Tech bed rack and iKamper Skycamp Mini mounted.
#4
Senior Member
Join Date: Jan 2013
Location: Norman, Oklahoma
Posts: 5,395
Bikes: Too many to list
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1765 Post(s)
Liked 1,124 Times
in
746 Posts
KISS
Motorcycle tie down straps i have found to be easier to deal with than the racks where you have to pop the front wheel off and secure it with a quick release -- just undo the straps and go
I however, use a Thule hitch mount with my Tacoma because i like to leave a bed cover on it to keep my tool boxes , gearbags and drink coolers, etc secure
Motorcycle tie down straps i have found to be easier to deal with than the racks where you have to pop the front wheel off and secure it with a quick release -- just undo the straps and go
I however, use a Thule hitch mount with my Tacoma because i like to leave a bed cover on it to keep my tool boxes , gearbags and drink coolers, etc secure
#5
Senior Member
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,883
Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7 AXS, Trek Emonda ALR AXS, Trek FX 5 Sport
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 1,744 Times
in
1,015 Posts
The bar with quick release hubs works. Check the below out. I'll be getting a new work truck in January and am gonna try these. They make 2 different kinds for depending on what type of bed rail. https://usa.innoracks.com/
I personally have a 1UP Hitchrack and I like not having to pull the wheel.
__________________
Brian | 2023 Trek Domane SLR 7 AXS | 2023 Trek CheckPoint SL 7 AXS | 2016 Trek Emonda ALR | 2022 Trek FX Sport 5
Brian | 2023 Trek Domane SLR 7 AXS | 2023 Trek CheckPoint SL 7 AXS | 2016 Trek Emonda ALR | 2022 Trek FX Sport 5
Last edited by jaxgtr; 10-13-21 at 06:29 PM.
Likes For hose:
#7
Senior Member
Join Date: Jul 2008
Location: Minas Ithil
Posts: 9,173
Mentioned: 66 Post(s)
Tagged: 0 Thread(s)
Quoted: 2432 Post(s)
Liked 638 Times
in
395 Posts
No need for all that. In my Silverado I just strap it down motorcycle style. A soft tie on each side of the bar attached to friction straps connected to the bed hooks. You can also attach a strap to each side of the rear of the bike. Takes about a minute to get her strapped in. Drove from New Jersey to El Paso like that with no problems.
You can get soft ties for three bucks.
https://www.harborfreight.com/soft-l...saAucDEALw_wcB
You can get soft ties for three bucks.
https://www.harborfreight.com/soft-l...saAucDEALw_wcB
#8
Member
Thread Starter
Join Date: Aug 2015
Posts: 26
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
Thanks folks, it's appreciated.
hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.
hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.
#10
Senior Member
Join Date: Jun 2015
Location: North Central Wisconsin
Posts: 4,624
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 2976 Post(s)
Liked 1,182 Times
in
771 Posts
Multiple bikes...you want a rack system of sorts to stand them up. Otherwise they can get scratched / damaged if they are piled on top of one another or leaned up against the bed sides.
I made a rack out of a 2 x 4 and some PVC pipe for my thru axle bikes.
Last edited by prj71; 10-14-21 at 09:36 AM.
#15
Senior Member
Join Date: Oct 2013
Location: Highlands Ranch, CO
Posts: 1,221
Bikes: '13 Diamondback Hybrid Commuter, '17 Spec Roubaix Di2, '17 Spec Camber 29'er, '19 CDale Topstone Gravel
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 590 Post(s)
Liked 445 Times
in
260 Posts
I'm getting a new SUV (Honda CRV) next week to that can transport my bikes in inside and upright (the CRV is the only vehicle I found that can do that with a 29er mtb, and I actually brought my mtb to all of the test drives just to test it out., and if the bike didn't fit, I didn't even bother to test drive it), and you just gave me the great idea to use 80/20 for the fork mounts so that I can easily adjust their positions.
Is there anything 80/20 can't do?!!
Is there anything 80/20 can't do?!!
#17
Junior Member
I use a tailgate pad. Wrapping something around the downtube before strapping it in prevents abrasion from the strap. My pad is a Dakine and carries 7 bikes.
#19
I like speed
I personally use the Thule Insta Gator on my F150; picked one up cheap from JensonUSA that had the box damaged in shipping.
Another option is to make your own PVC pipe rack for the bed and use bungees to hold it all in.
Another option is to make your own PVC pipe rack for the bed and use bungees to hold it all in.
Likes For oris:
#20
Full Member
Join Date: Jul 2019
Location: Greer, SC
Posts: 344
Bikes: GR300, Grail, Live Wire, 5010
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 189 Post(s)
Liked 241 Times
in
121 Posts
I used a Thule Instagater when I had a truck, it does a pretty good job, however the bar that holds the tire down is too wide to fit between the front tire and the down tube on my road bikes. It’s still usable, but you have to cock the wheel to the side when putting the bike in there. I’d think that a Ridgeline bed would be too short for most modern mountain bikes.
#22
Senior Member
Join Date: Aug 2009
Posts: 2,395
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 1562 Post(s)
Liked 1,734 Times
in
974 Posts
To be fair, My kids' bikes are 650c wheeled road bikes and my wife's bike is a small Terry style bike as well, So they are not 4 full sized bikes.
But I don't see why you couldn't lean and tie down 3 road bikes along the two sides and the back of the truck bed.
But I don't see why you couldn't lean and tie down 3 road bikes along the two sides and the back of the truck bed.
#23
Senior Member
Join Date: Jul 2006
Location: Jacksonville, FL
Posts: 6,883
Bikes: Trek Domane SLR 7 AXS, Trek CheckPoint SL7 AXS, Trek Emonda ALR AXS, Trek FX 5 Sport
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 768 Post(s)
Liked 1,744 Times
in
1,015 Posts
Thanks folks, it's appreciated.
hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.
hose , no you're not the only one. I'm just not willing to do that either with my tri bike, or for any distance. Personal choice.
+1. I just do not want to put my very expensive bikes in the back of my truck. It was worth it to me to spend the few hundred dollars for the hitch rack.
#24
Member
Bike in a small pickup
My favorite bike transportation method in my Ford Ranger is to run a 1/4" line from the saddle around the side rail at the top of the truck side bed wall and back to the stem. I do the line fastening with the bike standing upright a foot from the bed wall. When tied off, I brace my elbows on top of the bed side and grab the fork and seat stay and tilt the tires into the corner of the pickup wall and floor. The line is adjusted so the bike is leaning toward the mid-line of the truck at abut a 45 degree angle, and the tires perfectly span the wheel well, immobilizing the bike. We can fit two bikes in the Ranger short bed. To get the bikes out, just reverse the whole process. The Ranger bed is just long enough to close the tail gate. I have loops in the ends of my line, one with a slip knot, so adjustment is quick. For a longer trip I will tie the top of the bike to the other side of the truck bed, so if I was in a fender bender the bike would stay in the truck bed. This system also works on my Wife's Colorado.
Last edited by Blues; 10-17-21 at 07:47 PM. Reason: re-write and add photo
#25
Senior Member
Join Date: Jul 2007
Location: South shore, L.I., NY
Posts: 6,885
Bikes: Flyxii FR322, Cannondale Topstone, Miyata City Liner, Specialized Chisel, Specialized Epic Evo
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 3242 Post(s)
Liked 2,086 Times
in
1,181 Posts