Wheel building question
#1
Newbie
Thread Starter
Wheel building question
Hello Folks,
I am sourcing out parts for a rear wheel build, and I am pretty confused about the length of the spokes that I need. I used several spoke calculators and they all spit out different numbers, some are way off (see pictures below). What Gives? What do I actually need?
The wheel will be a Crest CB7 laced on a DT Swiss 350 classic with 12mm aluminum nipples, and nipple washers, 3x lacing.
Here's the numbers:
Hub:
Any help is appreciated. Thanks!
I am sourcing out parts for a rear wheel build, and I am pretty confused about the length of the spokes that I need. I used several spoke calculators and they all spit out different numbers, some are way off (see pictures below). What Gives? What do I actually need?
The wheel will be a Crest CB7 laced on a DT Swiss 350 classic with 12mm aluminum nipples, and nipple washers, 3x lacing.
Here's the numbers:
Hub:
- Hub Drilling: 32
- Center to Flange, Right: 20.2
- Spoke Interface: J-Bend
- Center to Flange, Left: 33
- Flange Diameter, Right: 46
- Flange Diameter, Left: 46
- Rear Axle: 12mm Thru x 142mm
Any help is appreciated. Thanks!
#2
Really Old Senior Member
I get the same numbers on SpokeCalc as the top w/ 2.6mm dia. spoke holes.
I would just get 292 for both, assuming the ERD is correct.
I would just get 292 for both, assuming the ERD is correct.
#3
Senior Member
Join Date: Nov 2014
Location: Eugene, Oregon, USA
Posts: 27,547
Mentioned: 217 Post(s)
Tagged: 0 Thread(s)
Quoted: 18382 Post(s)
Liked 4,515 Times
in
3,355 Posts
If at all possible, I like to get the rims and hubs in front of me so that I can do the measurements myself.
That way, I can also measure to the top of the nipples, and include any washers if I want.
That way, I can also measure to the top of the nipples, and include any washers if I want.
#4
Newbie
Thread Starter
yeah I think 292 seems good, I don't know why sapim's calculator is so off...
Are washers recommended? and should I add anything for them? This is on a Carbon Crest CB7, they don't mention anything about washers on their site, but I'm sure they can't hurt right?
Are washers recommended? and should I add anything for them? This is on a Carbon Crest CB7, they don't mention anything about washers on their site, but I'm sure they can't hurt right?
#5
Senior Member
I think the Sapim is off because they want the internal diameter of the rim and rim thickness, not the ERD, which is essentially the internal diameter of the rim plus 2x the rim thickness. I think that is a confusing. Measuring ERD is simpler.
Edit: I tried plugging your numbers in using the ERD for internal rim diameter and zero for rim thickness. I thought it would work, but I got 294/296 spoke lengths. Closer, but not close enough. I'm at a loss.
Edit: I tried plugging your numbers in using the ERD for internal rim diameter and zero for rim thickness. I thought it would work, but I got 294/296 spoke lengths. Closer, but not close enough. I'm at a loss.
Last edited by gearbasher; 05-28-21 at 06:26 PM.
Likes For gearbasher:
#6
Senior Member
Join Date: Feb 2007
Posts: 1,443
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 626 Post(s)
Likes: 0
Liked 402 Times
in
277 Posts
I trust most of the info on the wheel building calculators but always measure the ERD myself. Don't forget to add in double the thickness of one nipple washer If you use them. I like the Sapim spokes and their Polyax nipples.
#8
Senior Member
pro lock nipples are very hard to deal with. they add torsional stress and strain on the spokes. they have loctite like paste in them.
i would only use pro lock if dealing with 24x wheels and i would only use them on the non drive side flange spokes/nipples.
brass nipples are much better and you could use a beeswax based homebrew lube if you expect accidental large loads that would have otherwise had your down spoke momentarily lose tension (nipple able to unscrew at that point). that being one way a wheel goes out of true, gradually...
beeswax is a good thing, you could go with something better... just saying that beeswas can be a bit stiff once the spoke has momentarily lost tension so it can prevent nipple unscrew.
and lubricate the eyelets/nipple interface with a proper grease for the application. not saying what that would be - because lotsa folks can pop out and disagree on what would work best. i'll let you to trial and error. but the most important thing is this: grease is essential on the nipple/eyelets interface and not greases are equal. i tried with dura ace grease - which is calcium - and it is utter crap btw.
i would only use pro lock if dealing with 24x wheels and i would only use them on the non drive side flange spokes/nipples.
brass nipples are much better and you could use a beeswax based homebrew lube if you expect accidental large loads that would have otherwise had your down spoke momentarily lose tension (nipple able to unscrew at that point). that being one way a wheel goes out of true, gradually...
beeswax is a good thing, you could go with something better... just saying that beeswas can be a bit stiff once the spoke has momentarily lost tension so it can prevent nipple unscrew.
and lubricate the eyelets/nipple interface with a proper grease for the application. not saying what that would be - because lotsa folks can pop out and disagree on what would work best. i'll let you to trial and error. but the most important thing is this: grease is essential on the nipple/eyelets interface and not greases are equal. i tried with dura ace grease - which is calcium - and it is utter crap btw.
Last edited by adipe; 05-29-21 at 08:33 AM.
#9
Senior Member
i'd say go with 290 DS (right flange) and 292 NDS (left flange) and use butted spokes on the NDS. if you have good skills and knowledge you could go with quite thin spokes on the NDS (i can handle 1.5mm) but if you are a rookie and don't know how to deal with torsional stress/strain then go with 1.8mm. for the the NDS that is. i would go with 1.8mm DS and 1.5-1.65mm NDS but would recommend 2mm (plain) and 1.8mm (plain/butted) gauge spokes. there are some 1.8mm plain spokes which need nipples for that thread size.
as the computed numbers i got were 291.68 left 290.65 right from this site:
https://spokecalculator.qbp.com/spok...ator/calculate
i have entered in the exact numbers i saw on the OP post. did not bother with what 350 hub classic would really mean and rim too.
there's also more spoke elastic elongation on thin spokes which means that you should be more careful to balance radial runout with spoke tension variance. but you should do that first working on the DS flange at medium tension with the NDS spokes having a tiny bit of tension, just enough to adjust lateral true (to be able to properly adjust radial) - meaning DS spokes having 89.999 degrees angle from the rim to the hub at that moderate tension. after that stage is done then you should not touch DS nipples but work on NDS alone while building tension etc. that would suppose you have the eyelets bedding in with the nipples uniformly. one more reason professional wheel builders readjust DS (loosening NDS all the way again) before finishing the wheel.
as the computed numbers i got were 291.68 left 290.65 right from this site:
https://spokecalculator.qbp.com/spok...ator/calculate
i have entered in the exact numbers i saw on the OP post. did not bother with what 350 hub classic would really mean and rim too.
there's also more spoke elastic elongation on thin spokes which means that you should be more careful to balance radial runout with spoke tension variance. but you should do that first working on the DS flange at medium tension with the NDS spokes having a tiny bit of tension, just enough to adjust lateral true (to be able to properly adjust radial) - meaning DS spokes having 89.999 degrees angle from the rim to the hub at that moderate tension. after that stage is done then you should not touch DS nipples but work on NDS alone while building tension etc. that would suppose you have the eyelets bedding in with the nipples uniformly. one more reason professional wheel builders readjust DS (loosening NDS all the way again) before finishing the wheel.
Last edited by adipe; 05-29-21 at 09:04 AM.
#10
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,629
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,568 Times
in
1,579 Posts
If FBinNY still posted here, he'd quip that a man with two watches can never be sure what time it is.
With aluminum nipples and nipple washers, it'll be better to err on the side of too long than too short.
With aluminum nipples and nipple washers, it'll be better to err on the side of too long than too short.
Likes For ThermionicScott:
#11
Senior Member
#12
Full Member
be sure to mash the spokes down with the palm of your hand where they come out of the hub to get the bend right.
when they bend those spokes, they tend to creep back and lose a few degrees.
or they were never bent far enuff in the first place, or both.
when they bend those spokes, they tend to creep back and lose a few degrees.
or they were never bent far enuff in the first place, or both.