So what the heck am I doing wrong?
#1
Senior Member
Thread Starter
Join Date: Jul 2018
Location: Rolesville NC
Posts: 816
Bikes: Had an old Columbia in the 80's, here a used Schwinn hybrid, now a Cannondale Quick 3 and a Topstone 105..
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 249 Post(s)
Liked 306 Times
in
139 Posts
So what the heck am I doing wrong?
Trying to take the crank off my FSA crankset and it will not budge. I know the direction the nut has to turn. I have watched the videos on Youtube and they use hand pressure and it comes off easily. I am using an impact
driver and have soaked the nut with penetrating oil and it will not budge. What am I doing wrong? Any ideas are welcome as I am about to cut it off with a reciprocating saw. Only kidding but I am frustrated.
Any ideas?
Frank.
driver and have soaked the nut with penetrating oil and it will not budge. What am I doing wrong? Any ideas are welcome as I am about to cut it off with a reciprocating saw. Only kidding but I am frustrated.
Any ideas?
Frank.
#2
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 10,515
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 40 Post(s)
Tagged: 0 Thread(s)
Quoted: 2747 Post(s)
Liked 3,395 Times
in
2,056 Posts
More torque You're looking at 40 nm or about 30 ft/lb on it.
https://www.bikeforums.net/bicycle-m...oval-help.html
https://www.bikeforums.net/bicycle-m...oval-help.html
Likes For dedhed:
#3
Senior Member
Join Date: Jul 2006
Location: San Jose (Willow Glen) Ca
Posts: 9,846
Bikes: Kirk Custom JK Special, '84 Team Miyata,(dura ace old school) 80?? SR Semi-Pro 600 Arabesque
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 2338 Post(s)
Liked 2,822 Times
in
1,541 Posts
more leverage, no impact driver
__________________
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Life is too short not to ride the best bike you have, as much as you can
(looking for Torpado Super light frame/fork or for Raleigh International frame fork 58cm)
Likes For squirtdad:
#6
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,084
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4205 Post(s)
Liked 3,864 Times
in
2,312 Posts
Static fittings friction is generally greater then dynamic friction. So a tighten torque value is usually less then the loosening amount.
Also penetrating fluids are really poor lubricating ones. So replacing the lube between the bolt and the LH threaded cap could have further increased the friction between them, this added to the "stiction" of the axle and arm fit can add up to be pretty high. Andy
Also penetrating fluids are really poor lubricating ones. So replacing the lube between the bolt and the LH threaded cap could have further increased the friction between them, this added to the "stiction" of the axle and arm fit can add up to be pretty high. Andy
__________________
AndrewRStewart
AndrewRStewart
Likes For Andrew R Stewart:
Likes For cobba:
#8
Senior Member
The solution is leverage, not an impact driver.
Likes For cpach:
#9
Senior Member
Join Date: Sep 2020
Location: Eastern Poland
Posts: 744
Bikes: Romet Jubilat x 4, Wigry x 1, Turing x 1
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 194 Post(s)
Liked 204 Times
in
151 Posts
The solution is a lot more leverage, with something to securely support what you are trying to loosen and your tool. Impact drivers, while they have their uses, are brutish devices that dissipate your energy in all kinds of directions. Many eons ago, when I was a car mechanic back in the days when an air wrench was used almost solely to remove wheel nuts (yes, that long ago...), the company impact drivers rarely saw the light of day while our lever bars wouldn't have shamed a post-apocalyptic warrior's great grandson.
If your tool can take it, a scaffold tube is always an option
If your tool can take it, a scaffold tube is always an option
Likes For Geepig:
#10
Senior Member
Add a long tube to the end of the hex key to have more leverage. It should work.
Likes For Amt0571:
#11
Senior Member
Thread Starter
Join Date: Jul 2018
Location: Rolesville NC
Posts: 816
Bikes: Had an old Columbia in the 80's, here a used Schwinn hybrid, now a Cannondale Quick 3 and a Topstone 105..
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 249 Post(s)
Liked 306 Times
in
139 Posts
Thanks all. Will pick up an 8mm on 3/8" drive and lay into it.
Frank.
Frank.
#12
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,673
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 837 Post(s)
Liked 1,061 Times
in
745 Posts
I recommend taking off the self extracting ring and use a proper crank extractor tool in this case. If the crank is not coming off without a lot of force there is a good chance you'll ruin the SE ring and possibly strip some of the threads on the crank arm.
Likes For Crankycrank:
#13
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,987
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6193 Post(s)
Liked 4,810 Times
in
3,318 Posts
Is the bolt stuck and won't loosen from the crank shaft, or is the bolt tightening against the self removal ring and then getting tight? On my RaceFace crank arm, there is a turn or two of the bolt before it tightens against the self removal ring. But it didn't take much torque to get the crank arm off.
You are turning the wrench counter clockwise as the arrow on the removal ring shows?
Sometimes trying to tighten a bolt will move it enough to break the stiction and it'll be easier to loosen. Just don't over torque it too much.
You are turning the wrench counter clockwise as the arrow on the removal ring shows?
Sometimes trying to tighten a bolt will move it enough to break the stiction and it'll be easier to loosen. Just don't over torque it too much.
Likes For Iride01:
Likes For andrewclaus:
#15
Senior Member
Thread Starter
Join Date: Jul 2018
Location: Rolesville NC
Posts: 816
Bikes: Had an old Columbia in the 80's, here a used Schwinn hybrid, now a Cannondale Quick 3 and a Topstone 105..
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 249 Post(s)
Liked 306 Times
in
139 Posts
So leverage is my new favorite word. 8mm Allen and a 30" piece of 3/4" iron pipe done. Now to find out what the bottom bracket dimension is and I can order my new crank and BB.
Thank you all for the information. I blocked the crank arm and put my 190 lbs on the pipe and the rest is history. Fantastic.
Frank.
Thank you all for the information. I blocked the crank arm and put my 190 lbs on the pipe and the rest is history. Fantastic.
Frank.
Last edited by Helderberg; 04-27-21 at 03:51 PM.
Likes For Helderberg:
#16
Senior Member
So leverage is my new favorite word. 8mm Allen and a 30" piece of 3/4" iron pipe done. Now to find out what the bottom bracket dimension is and I can order my new crank and BB.
Thank you all for the information. I blocked the crank arm and put my 190 lbs on the pipe and the rest is history. Fantastic.
Frank.
Thank you all for the information. I blocked the crank arm and put my 190 lbs on the pipe and the rest is history. Fantastic.
Frank.
Likes For Amt0571: