Ultegra 8050 or 6870?
#26
Senior Member
Thread Starter
#27
Woman make me faster
Never seen that information before, thank you dvdslw. Looks like a good page to keep as reference.
#28
Achtung!
Join Date: Oct 2015
Location: New England
Posts: 1,673
Bikes: 60.1, Marvel
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 515 Post(s)
Liked 268 Times
in
161 Posts
I realize I’m bumping an old thread, but I have a 2015 Pinarello Marvel with mechanical Ultegra 6800 (rim brake if that makes any difference). There was a 6870 model when I bought the bike new many years ago and I’m now kicking myself for not just buying the 6870 model at the time. Anyhoo, I’ve toyed with the idea of going to 6870 and have found a few used sets online, but I’m wondering if I can go up 8050 or even Dura Ace 9070 (don’t need DA but will consider it if it can directly bolt on to my bike) without any issues. My biggest concern is modifying the frame (drilling) to make space for a new groupset.
I’m aware the cost of converting can be very high, but I’d try to put my 6800 on my wife’s 105 5800 Domane and then sell the 105 bits. I really, really love this bike and don’t have any plans/interest in getting a new road bike (searching for a new TT bike to replace the P3 I sold some time ago).
Can I go directly from 6800 to 8050 without drilling holes or making serious frame modifications or am I stuck going to 6870 only? Would like the 12th gear but it’s by no means necessary.
Again - I realize this is an old thread, but I very much appreciate your thoughts and guidance
I’m aware the cost of converting can be very high, but I’d try to put my 6800 on my wife’s 105 5800 Domane and then sell the 105 bits. I really, really love this bike and don’t have any plans/interest in getting a new road bike (searching for a new TT bike to replace the P3 I sold some time ago).
Can I go directly from 6800 to 8050 without drilling holes or making serious frame modifications or am I stuck going to 6870 only? Would like the 12th gear but it’s by no means necessary.
Again - I realize this is an old thread, but I very much appreciate your thoughts and guidance
#29
Obsessed with Eddington
Join Date: Jun 2013
Location: Brussels (BE) 🇧🇪
Posts: 1,330
Bikes: '16 Spesh Diverge, '14 Spesh Fatboy, '18 Spesh Epic, '18 Spesh SL6, '21 Spesh SL7, '21 Spesh Diverge...and maybe n+1?
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 532 Post(s)
Liked 621 Times
in
368 Posts
I'm confused. Why would you modify (drill) your frame? Doesn't it already internally route the cables? If so, you'd use the same routing for the new brake cabling and the e-tube wiring. I must be missing something.
#30
Achtung!
Join Date: Oct 2015
Location: New England
Posts: 1,673
Bikes: 60.1, Marvel
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 515 Post(s)
Liked 268 Times
in
161 Posts
I didn’t know if the newer units were the same size and therefore use the same holes as where the existing 6800 is. Yes, there is internal cable routing.
#31
Obsessed with Eddington
Join Date: Jun 2013
Location: Brussels (BE) 🇧🇪
Posts: 1,330
Bikes: '16 Spesh Diverge, '14 Spesh Fatboy, '18 Spesh Epic, '18 Spesh SL6, '21 Spesh SL7, '21 Spesh Diverge...and maybe n+1?
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 532 Post(s)
Liked 621 Times
in
368 Posts
My first Di2 install (68xx) was on a 2015 Trek Madone 5 frame. Like your frame, it used internally routed cabling. The only thing I needed to acquire were the Di2 specific grommets for the frame holes (left side for the wiring to enter the frame next to the rear brake cable housing and right side to close the hole in the frame). Honestly, this was more about a "clean" install than any sort of requirement to run the Di2 wire from the A-Jct (under the stem) to B-Jct (at the bottom bracket), it would have been possible to run the wires without the specific grommets. Check with Pinarello and see if they have a similar Di2 adapter kit, otherwise just run the wires like you'd run shift cables. There should be no need to modify the frame.
Likes For Badger6:
#32
Achtung!
Join Date: Oct 2015
Location: New England
Posts: 1,673
Bikes: 60.1, Marvel
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 515 Post(s)
Liked 268 Times
in
161 Posts
My first Di2 install (68xx) was on a 2015 Trek Madone 5 frame. Like your frame, it used internally routed cabling. The only thing I needed to acquire were the Di2 specific grommets for the frame holes (left side for the wiring to enter the frame next to the rear brake cable housing and right side to close the hole in the frame). Honestly, this was more about a "clean" install than any sort of requirement to run the Di2 wire from the A-Jct (under the stem) to B-Jct (at the bottom bracket), it would have been possible to run the wires without the specific grommets. Check with Pinarello and see if they have a similar Di2 adapter kit, otherwise just run the wires like you'd run shift cables. There should be no need to modify the frame.
Likes For thin_concrete: