What's happening with tradition?
#26
Senior Member
Thread Starter
Likes For gearbasher:
#27
Senior Member
Thread Starter
#28
Senior Member
Thread Starter
I believe the idea is: With the valve on top and the tire label aligned with the valve, you can read the tire, rim and hub and nothing is upside down (of course...this is reading from the right!).
#29
Full Member
Join Date: Aug 2019
Location: Albuquerque
Posts: 227
Bikes: 1st Track bike: 1978 Speedwell titanium 1st Road bike: 2001 Independent Fabrication Crown Jewel
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 97 Post(s)
Liked 116 Times
in
65 Posts
I like tradition and I'm anal about it. In this particular case, it has to do with wheels reading from the right. I always build my wheels so the rims read from the right. Unless they are decaled both ways. I always mount my tires so the label is on the right. But, these days, most tires are labeled on both sides. I also make sure my rim strips / tape also read from the right. I know, no one's gonna see it. So why bother? Well what upset me is a set of wheels I built with Miche Primato hubs. I built these a while ago and it bothered me back then. But today, when I stopped at a light and looked down, it just got to me. With the Miche hubs, the brand reads from the rear (as it should) but Primato and Made in Italy read from the left. Pisses me off. You would think an Italian company would keep up with tradition.
Or...am I being too anal?
Photos: Excuse the dirt, but I'm a firm believer of spending more time riding the bike than cleaning it.
Or...am I being too anal?
Photos: Excuse the dirt, but I'm a firm believer of spending more time riding the bike than cleaning it.
To each his own...
Likes For Biketiger:
#31
Senior Member
Join Date: Feb 2008
Location: Peoria, IL
Posts: 4,476
Mentioned: 86 Post(s)
Tagged: 0 Thread(s)
Quoted: 1829 Post(s)
Liked 3,375 Times
in
1,580 Posts
in any case, it seems to have become an indicator of quality or "thoroughness", so I've tried to do it. Here's a shot of a wheel I build for a friend a few years ago...
Steve in Peoria
#32
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,395 Times
in
2,092 Posts
#33
Senior Member
Join Date: Aug 2016
Posts: 712
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 283 Post(s)
Liked 262 Times
in
164 Posts
Old school: Attention to detail demonstrates a high level of craftsmanship attained by the builder.
New School: Build just good enough that when our widget fails it's past the pseudo warranty period and not our problem.
New School: Build just good enough that when our widget fails it's past the pseudo warranty period and not our problem.
#34
Senior Member
Thread Starter
BTW: Miche did get it right with their RC2 Racing Box Hubs.
#35
Senior Member
Join Date: Oct 2014
Location: GWN
Posts: 2,538
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 1858 Post(s)
Liked 606 Times
in
403 Posts
I have 2 sets of FB (Fratelli Brivio) hubs, Italian made. One is branded Paglianti, made sometime in the mid to late 1930s. The other is branded Frejus CdM, made in the early 1940s. Both are readable from the non-drive side.
When did this so-called "tradition" of readable on the drive side begin?
When did this so-called "tradition" of readable on the drive side begin?
#36
Full Member
Join Date: Apr 2018
Location: NYC
Posts: 383
Bikes: '72 Raleigh Super Course; '90 Cannondale ST1000; '98/99 Cannondale T700; 2002 Cannondale CAAD5 R700; 2022 Cannondale Topstone 2L
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 166 Post(s)
Liked 348 Times
in
156 Posts
Couldn't the offending stickers be... removed?
Likes For Rooney:
#37
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,395 Times
in
2,092 Posts
Likes For cudak888:
#38
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 13,519
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 54 Post(s)
Tagged: 0 Thread(s)
Quoted: 4355 Post(s)
Liked 3,993 Times
in
2,665 Posts
#39
Senior Member
Join Date: Dec 2019
Location: South Shore of Long Island
Posts: 2,799
Bikes: 2010 Carrera Volans, 2015 C-Dale Trail 2sl, 2017 Raleigh Rush Hour, 2017 Blue Proseccio, 1992 Giant Perigee, 80s Gitane Rallye Tandem
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1088 Post(s)
Liked 1,024 Times
in
723 Posts
I've had the same nuisance with King front disc hubs, the logo can't be read from the drive side, don't know why they put it backwards. I'd be more fine with the whole thing if it was consistent front and back but to orient one hub differently is just annoying.
Its a problem with disc wheels, I build my wheels with the outer spoke pulling but with a disc hub the outer spoke on the disc side should actually be opposite and pushing. To get the valve between parallel spokes requires switching up the non-drive spokes.
Its a problem with disc wheels, I build my wheels with the outer spoke pulling but with a disc hub the outer spoke on the disc side should actually be opposite and pushing. To get the valve between parallel spokes requires switching up the non-drive spokes.
Likes For Rooney:
#43
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,395 Times
in
2,092 Posts
#44
Senior Member
Join Date: Jan 2005
Location: Baltimore, MD
Posts: 5,373
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 2482 Post(s)
Liked 2,955 Times
in
1,678 Posts
Likes For Trakhak:
#45
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
Tradition is peer pressure from dead people...... somebody
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
Likes For Bianchigirll:
#46
Bike Butcher of Portland
Join Date: Jul 2014
Location: Portland, OR
Posts: 11,639
Bikes: It's complicated.
Mentioned: 1299 Post(s)
Tagged: 0 Thread(s)
Quoted: 4682 Post(s)
Liked 5,799 Times
in
2,284 Posts
when did that weird bit of OCD first appear? I sure don't recall hearing of it back in the 70's or 80's, but I wasn't hanging around with the OCD folks either.
in any case, it seems to have become an indicator of quality or "thoroughness", so I've tried to do it. Here's a shot of a wheel I build for a friend a few years ago...
Steve in Peoria
in any case, it seems to have become an indicator of quality or "thoroughness", so I've tried to do it. Here's a shot of a wheel I build for a friend a few years ago...
Steve in Peoria
__________________
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
If someone tells you that you have enough bicycles and you don't need any more, stop talking to them. You don't need that kind of negativity in your life.
#47
Half way there
Join Date: Sep 2015
Location: North Carolina
Posts: 2,957
Bikes: Many, and the list changes frequently
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 986 Post(s)
Liked 880 Times
in
527 Posts
If your practice gives you satisfaction, go for it. Perhaps you're a bit anal but so are most others about this or the other. I generally follow the convention but admit to building wheels the exact opposite of convention, just to be contrarian (and perhaps cause panic among other riders).
You do realize that when you're riding the bike, it's impossible to ascertain the orientation of the labels?
Photos: Excuse the dirt, but I'm a firm believer of spending more time riding the bike than cleaning it.
Likes For Moe Zhoost:
#48
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,786
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3588 Post(s)
Liked 3,400 Times
in
1,934 Posts
I'd be more concerned about the open-cam quick release on a horizontal dropout than the orientation of the letters on the hub.
Likes For JohnDThompson:
#49
Senior Member
Thread Starter
Since Campy's newest Record hubs have open cams, 4 of my 6 bikes now have them. All are horizontal drops. Only once did the rear wheel cock on me. And, that was my fault. I never made my quick releases very tight when I used the closed cam hubs. So, I did the same with the open cam. From a track stand to a hard launch, I pulled the wheel into the left chain stay.. I now make them tighter, and it never happened again.