Old Bianchi, new crankset
07-30-23, 10:53 AM
#1
Newbie
Thread Starter
Join Date: Jul 2023
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Old Bianchi, new crankset
I want to replace the crankset on this Bianchi Via Nirone from 2006 to make it look more modern. What would fit?
07-30-23, 11:22 AM
#2
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 15,002
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6198 Post(s)
Liked 4,814 Times
in
3,321 Posts
Most any crankset that has a BB compatible with your BB shell on the bike. You should also consider if the crankset is appropriate to that genre of bike and the number of speeds on the rear as that will determine the chain line that crank will or should give.
Figuring out what the BB shell is made for is your first step. Threaded or press fit, shell width, diameter and etc.
Welcome to BF. If you have a picture you wish to show us, then put it in the Galleryuntil you get 10 posts and can do them yourself. Let us know if you put them there and someone might link them for you.
Figuring out what the BB shell is made for is your first step. Threaded or press fit, shell width, diameter and etc.
Welcome to BF. If you have a picture you wish to show us, then put it in the Galleryuntil you get 10 posts and can do them yourself. Let us know if you put them there and someone might link them for you.
Last edited by Iride01; 07-30-23 at 11:25 AM.
07-30-23, 06:24 PM
#3
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,726
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,592 Times
in
1,436 Posts
A simple measurement will tell you all you need to know.
First eyeball to know whether it's threaded, then measure width.
Odds greatly favor a 68mm, 24 x 1.37" standard BB. If so pick whatever BB and crankset you like from the many available. If only buying the BB make sure it matches your crankset.
First eyeball to know whether it's threaded, then measure width.
Odds greatly favor a 68mm, 24 x 1.37" standard BB. If so pick whatever BB and crankset you like from the many available. If only buying the BB make sure it matches your crankset.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
07-31-23, 07:28 PM
#5
cowboy, steel horse, etc
Join Date: Sep 2008
Location: The hot spot.
Posts: 44,859
Bikes: everywhere
Mentioned: 72 Post(s)
Tagged: 1 Thread(s)
Quoted: 12784 Post(s)
Liked 7,697 Times
in
4,086 Posts
Likes For LesterOfPuppets:
08-30-23, 07:27 PM
#6
Newbie
Join Date: Aug 2023
Location: Central Florida
Posts: 18
Bikes: '80's Centerion Iron Man (purchased New) , ~'91 Specialized ($50 FaceBook Find), '?? Specialized Cross roads ($20 thrift Store Find)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked 18 Times
in
6 Posts
that record crank is like expensive jewelry looks awesome
08-30-23, 09:44 PM
#7
Senior Member
Join Date: Apr 2011
Posts: 7,077
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4416 Post(s)
Liked 1,567 Times
in
1,029 Posts
The frame will accept nearly every crank available. The current Campagnolo Veloce(?) bottom bracket may not work with much of anything. Which are you trying to fit to? And what kind of crank would you like?
Likes For Kontact:
09-01-23, 10:20 AM
#8
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,398
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 514 Post(s)
Liked 451 Times
in
339 Posts
On top of that, the inter-chainring spacing on these Campagnolo cranks is different from the Shimano/SRAM standard. Unless you're also planning to swap the shifters, derailleur, cassette, rear wheel, and chain, leave it alone.
09-01-23, 12:32 PM
#9
Newbie
Join Date: Sep 2023
Location: manchester
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Bianchi Via Nirone from 2006
likely 68mm threaded as thats what most roadbikes had at the time.
bianchi were allowing for english /bsa 68mm a lot
you can put shimano / campag on it.
just match the bb to the cranks. egs. shimanos have square taper, octalink, isis
bianchi were allowing for english /bsa 68mm a lot
you can put shimano / campag on it.
just match the bb to the cranks. egs. shimanos have square taper, octalink, isis
09-01-23, 12:49 PM
#10
Senior Member
Join Date: Apr 2011
Posts: 7,077
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4416 Post(s)
Liked 1,567 Times
in
1,029 Posts
09-01-23, 02:01 PM
#12
Senior Member
Join Date: Apr 2011
Posts: 7,077
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4416 Post(s)
Liked 1,567 Times
in
1,029 Posts
That's because later Shimano cranks have wider spacing than standard. 10 speed Sram, Campy and Shimano were the same.
09-01-23, 04:22 PM
#13
Senior Member
Join Date: Jul 2022
Location: Pac NW
Posts: 1,948
Bikes: several Eddy Merz (ride like Eddy, braze like Jim!)
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 1086 Post(s)
Liked 1,824 Times
in
665 Posts
um,
twice people have guessed the width to be 68.
Italians were famous for using 70MM
twice people have guessed the width to be 68.
Italians were famous for using 70MM
__________________
"Leave the gun. Take the Colnagos."
"Leave the gun. Take the Colnagos."
09-01-23, 10:50 PM
#14
Senior Member
Join Date: Apr 2011
Posts: 7,077
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4416 Post(s)
Liked 1,567 Times
in
1,029 Posts
But you never know, and hopefully the OP looks for markings or dimensions rather than just taking our word for it.
09-03-23, 06:41 AM
#15
Senior Member
Join Date: Jun 2020
Location: Maryland
Posts: 1,380
Bikes: 1982 Bianchi Sport SX, Rayleigh Tamland 1, Rans V-Rex recumbent, Fuji MTB, 80's Cannondale MTB with BBSHD ebike motor
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 668 Post(s)
Liked 529 Times
in
355 Posts
I put a Campy Centar Ultratorque crank on my 1982 Bianchi. Got it close out cheaper than replacing the pair of chain rings on the original Sugino crank. When I swapped out the Bianchi frame with a Tomassini frame all I had to do was buy some Italian thread bearings to replace the BSA threads on the old frame.
09-03-23, 08:33 AM
#16
Senior Member
Join Date: Sep 2004
Location: Chicago area
Posts: 2,556
Bikes: Airborne "Carpe Diem", Motobecane "Mirage", Trek 6000, Strida 2, Dahon "Helios XL", Dahon "Mu XL", Tern "Verge S11i"
Mentioned: 23 Post(s)
Tagged: 0 Thread(s)
Quoted: 980 Post(s)
Liked 584 Times
in
401 Posts
That is elegant in its simplicity! The Dura-Ace crankset looks like someone's idea of a 23rd-century spaceship part.
Not as light as the Record, but to my sensibilities this triple looks less massive than the Dura-Ace double.
Not as light as the Record, but to my sensibilities this triple looks less massive than the Dura-Ace double.
09-03-23, 10:36 AM
#17
Senior Member
Join Date: Sep 2009
Posts: 1,972
Bikes: Habanero Titanium Team Nuevo
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 399 Post(s)
Liked 185 Times
in
121 Posts
This is a no brainer to me you have a threaded BB. Could be Italian threaded but I doubt it, and in any case you just get the correct Shimano bottom bracket. In my book Shimano has it over everyone on hollowtech cranks and external bearning bottom bracket. A simply R7000 crankset with BB60 bottom bracket and you will install and forget about it except that it will perform and work with the best. I have always said that Shimano Cranks, chains, and cassette simply work with the best for sure. The front shifting in particular.
09-03-23, 12:25 PM
#18
Senior Member
Join Date: Apr 2011
Posts: 7,077
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 4416 Post(s)
Liked 1,567 Times
in
1,029 Posts
This is a no brainer to me you have a threaded BB. Could be Italian threaded but I doubt it, and in any case you just get the correct Shimano bottom bracket. In my book Shimano has it over everyone on hollowtech cranks and external bearning bottom bracket. A simply R7000 crankset with BB60 bottom bracket and you will install and forget about it except that it will perform and work with the best. I have always said that Shimano Cranks, chains, and cassette simply work with the best for sure. The front shifting in particular.
There was and is nothing wrong with any of the previous crank types - ramped and pinned chainrings are old news.
Of course, we have no idea what the OP is trying to accomplish. The crank on that bike is decent.
