122, 128, 130 BCD - all with 38T smallest ring?
#1
Senior Member
Thread Starter
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,117
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1451 Post(s)
Liked 1,402 Times
in
768 Posts
122, 128, 130 BCD - all with 38T smallest ring?
I'm working on my son's bike (Raleigh Competition) which has a later Nervar Star crank. According to Velobase it has a 128 BCD. Looking at Sheldon Brown's five-arm crank crib sheet, I see that the smallest chainring is given as 38 teeth. That's what's on the crank now. The table lists 38T as the smallest chainring for 122 and 130 BCD as well. I assume that must not be the theoretical minimum, but the practical minimum (the smallest produced by the manufacturer). Or are the chainring bolt diameters sufficiently different that it affects the smallest possible chainring?
#2
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,292
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3818 Post(s)
Liked 3,359 Times
in
2,191 Posts
-----
Sutherland lists:
38T as smallest for 122
38T as smallest for NERVAR 128
39T as smallest for all 130's
-----
Sutherland lists:
38T as smallest for 122
38T as smallest for NERVAR 128
39T as smallest for all 130's
-----
#3
ambulatory senior
Join Date: Dec 2016
Location: Peoria Il
Posts: 5,999
Bikes: Austro Daimler modified by Gugie! Raleigh Professional and lots of other bikes.
Mentioned: 76 Post(s)
Tagged: 0 Thread(s)
Quoted: 1956 Post(s)
Liked 3,662 Times
in
1,680 Posts
Likes For 52telecaster:
#4
working on my sandal tan
Join Date: Aug 2011
Location: CID
Posts: 22,630
Bikes: 1991 Bianchi Eros, 1964 Armstrong, 1988 Diamondback Ascent, 1988 Bianchi Premio, 1987 Bianchi Sport SX, 1980s Raleigh mixte (hers), All-City Space Horse (hers)
Mentioned: 98 Post(s)
Tagged: 0 Thread(s)
Quoted: 3871 Post(s)
Liked 2,571 Times
in
1,579 Posts
38T is definitely possible for 130mm BCD. I have one, but I see evidence that the chain plates are able to contact the mounting tabs on the crank spider. I wonder if that is why most production chainrings are a tooth or two bigger than their theoretical minimum.
@jonwvara makes a 37T 122mm BCD ring, of course.
@jonwvara makes a 37T 122mm BCD ring, of course.
Likes For ThermionicScott:
#5
ambulatory senior
Join Date: Dec 2016
Location: Peoria Il
Posts: 5,999
Bikes: Austro Daimler modified by Gugie! Raleigh Professional and lots of other bikes.
Mentioned: 76 Post(s)
Tagged: 0 Thread(s)
Quoted: 1956 Post(s)
Liked 3,662 Times
in
1,680 Posts
38T is definitely possible for 130mm BCD. I have one, but I see evidence that the chain plates are able contact the mounting tabs on the crank spider. I wonder if that is what is why most production chainrings are a tooth or two bigger than their theoretical minimum.
@jonwvara makes a 37T 122mm BCD ring, of course.
@jonwvara makes a 37T 122mm BCD ring, of course.
Likes For 52telecaster:
#6
Senior Member
Join Date: Feb 2013
Location: Alta California
Posts: 14,292
Mentioned: 415 Post(s)
Tagged: 1 Thread(s)
Quoted: 3818 Post(s)
Liked 3,359 Times
in
2,191 Posts
-----
the 39T limit on 130 BCD sets listed on me Sutherland is likely due to it being a fairly early edition
Howard revises the manual every few years
-----
the 39T limit on 130 BCD sets listed on me Sutherland is likely due to it being a fairly early edition
Howard revises the manual every few years
-----
Likes For juvela:
#7
verktyg
Join Date: Jul 2006
Location: SF Bay Area
Posts: 4,030
Bikes: Current favorites: 1988 Peugeot Birraritz, 1984 Gitane Super Corsa, 1980s DeRosa, 1981 Bianchi Campione Del Mondo, 1992 Paramount OS, 1988 Colnago Technos, 1985 RalieghUSA SBDU Team Pro
Mentioned: 207 Post(s)
Tagged: 0 Thread(s)
Quoted: 1036 Post(s)
Liked 1,239 Times
in
655 Posts
Smallest Chainrings
Over the years I've found that at least 5-15% of the specs in Sutherland's Handbooks are wrong or . I have a second edition the we used back in the 70's (error factor 15%) and a 5th edition that covers the C&V era that I'm interested in (5-10% error factor).
37T were the smallest 122mm BCD chainrings that Stronglight produced. This 1980 catalog page shows the 105 Bis "drillium" chainrings but they made 37T standard chainrings too. They don't show up in any catalog prior to 1980 but... I have at least 15 bikes with Stronglight 49, 93, 104 and 105 cranks that I've mounted what I thought to be 38T chainrings on. When doing a tooth count, I found that over 1/3rd of them are actually 37T rather than 38T! Several date back to the late 1970's.
The 3 silver chainrings are 38T - the black one is 37T.
Shimanos are the only 130mm BCD cranks that I have experience with. I found that some of them are limited to a 39T small chainring without a modification.
Shimano 600 Crank with a 39T chainring.
A 38T chainring on the same crank. The chain will drag when going over the top of the spider arm.
I'm running 48T or 49T outer chainrings with 38T inners on most of my Shimano cranks. File about 1mm to 1.5mm off of the spider above the chainring bolt hole. This minor modification solves the clearance problem.
In defense of Sutherland's, during the bike boom, many bikes were sold or serviced by shops with little or no experience working on derailleur bikes; e.g. lawn mower shops, ski shops and so on. Sutherland's was a good resource for those kinds of businesses when for example they needed to replace a BB and so on.
Some of the dimensional specs were off when it came to little nuances like components with wide open manufacturing tolerances like BBs, hubs, FWs, and headsets. It was better than nothing because we had to learn ourselves by trial and error. We focused on better quality bikes so it became an issue for us.
juvela I'm not picking on you... just pointing out & sharing weird exceptions learned the hard way....
verktyg
__________________
Don't believe everything you think! History is written by those who weren't there....
Chas. ;-)
Don't believe everything you think! History is written by those who weren't there....
Chas. ;-)
Last edited by verktyg; 05-18-22 at 07:07 PM.
Likes For verktyg:
#8
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,999
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 2,580 Times
in
1,080 Posts
Stronglight 93 et al. at 122mm should be able to take a 36t with a little trimming of the spider arm tabs. I plan to make one, have the holes marked out, needs drilling counterboring and trimming, just haven't got a round tooit.
CAD drawing is from here.
Mark B
CAD drawing is from here.
Mark B
Likes For bulgie:
#9
Senior Member
Join Date: Oct 2010
Posts: 8,530
Mentioned: 69 Post(s)
Tagged: 0 Thread(s)
Quoted: 3244 Post(s)
Liked 2,523 Times
in
1,516 Posts
Technically not true for the 130. There are some 130 cranks out there drilled for an 86 3rd ring. Takagi made triples in both 130/86 and 110/74. I'm guessing some other brands did as well.
#10
verktyg
Join Date: Jul 2006
Location: SF Bay Area
Posts: 4,030
Bikes: Current favorites: 1988 Peugeot Birraritz, 1984 Gitane Super Corsa, 1980s DeRosa, 1981 Bianchi Campione Del Mondo, 1992 Paramount OS, 1988 Colnago Technos, 1985 RalieghUSA SBDU Team Pro
Mentioned: 207 Post(s)
Tagged: 0 Thread(s)
Quoted: 1036 Post(s)
Liked 1,239 Times
in
655 Posts
Doubles Not Triples
verktyg
__________________
Don't believe everything you think! History is written by those who weren't there....
Chas. ;-)
Don't believe everything you think! History is written by those who weren't there....
Chas. ;-)
Last edited by verktyg; 05-19-22 at 12:20 AM.
Likes For verktyg:
#11
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,811
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3597 Post(s)
Liked 3,418 Times
in
1,944 Posts
You can file a little material off the end of the spider arm to prevent this. Ofmega actually machined their 144mm BCD cranks to provide clearance for a 41T ring, which was otherwise subject to the same issue:
Likes For JohnDThompson:
#12
Senior Member
Thread Starter
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,117
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1451 Post(s)
Liked 1,402 Times
in
768 Posts
While I appreciate the discussion of all the possibilities in the surrounding BCDs, is there any chance a 36T or 37T 128BCD chainring for Nervar Star cranks was ever produced?
#13
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,999
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 2,580 Times
in
1,080 Posts
Probably completely impossible at 36t, unless there's some hack I haven't considered.
The website I use, that does CAD simulations based on BCD and teeth, doesn't have Nervar as a choice in its drop-down menu.
But if you put in 37 and 130 mm, you see the "valley" between two teeth actually touches the bolt hole. Nervar has a bolt circle radius just one mm smaller, so you could get that silly millimeter of clearance if you were desperate enough. Maybe with a smaller bolt diameter, smaller hole?Do the same thing at 36t and I think you'll agree — ain't happenin':That's not even the worst place, a couple of the other holes overlap the chain roller even more — maybe I shouldn't have cropped the screenshot that way.
Mark B
Likes For bulgie:
#14
Senior Member
Thread Starter
Join Date: Aug 2007
Location: Evanston, IL
Posts: 5,117
Bikes: many
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1451 Post(s)
Liked 1,402 Times
in
768 Posts
Thanks, Mark. Seems if I want to go lower I'd be better off searching for a 122BCD or 86BCD crank. Jake's young. I think he can handle it.
#15
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,999
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 2,580 Times
in
1,080 Posts
- A factory-made triplizer middle ring for 130 BCD (TA, Stronglight, Shimano, Mavic, Willow, FSA or Thorn) can be adapted to 128. You only need to ovalize the holes by 1 mm each, like with a file or dremel. Looks a little wonky, but only if you look real close, and it works fine.
- Or a new triplizer can be made with an actual 128 mm BCD (no ovalized holes) by starting out with a 38t ring with a 74 mm bolt pattern. Rare but they're out there, I know where to get one right now. Then you add 5 new holes at 128 mm, and the granny bolts to the original 74 mm holes. I have done this, works a treat. Oh yeah you have to cut the inner "shelves" off the spider arms, like making it into a Track crank. The "shelfectomy" is a 15 minute job if you have a vise, hacksaw and file, and you are handy.
- Or a new triplizer can be made with an actual 128 mm BCD (no ovalized holes) by starting out with a 38t ring with a 86 mm bolt pattern, that is, a Stronglight 99 ring, not quite as rare. Then proceed as in item #2 including the shelfectomy.
- Finally there's the Campy old-Record (aka "NR") way, where the 5 spider arms are drilled and tapped for stand-off bolts that the granny attaches to. Here's one I made that way to take an 86 mm Stronglight 99 granny ring:
That's time-consuming ($$), and even just the 5 Campy #818 standoff bolts often sell for well over $100. Though there are cheaper alternatives to the Campy bolts shown here, like generic industrial bolts from McMaster, this is only really an option for someone (like me) who's just crazy about their Nervar Star and nothing else will do. For most sane individuals, there are easier ways to get the needed gearing. If you're one of the crazy ones, let's talk.
Mark B
Last edited by bulgie; 05-20-22 at 07:15 PM.
Likes For bulgie:
#16
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,336 Times
in
842 Posts
I am using an Origin8 38T chainring on a Shimano spider with an SRAM PC-58 chain on the Bianchi without any issues. The chain links do ride on the ends of the spider, but this does not appear to cause any issues.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
Likes For John E:
#17
Senior Member
Join Date: May 2013
Location: Greenwood SC USA
Posts: 2,253
Bikes: 2002 Mercian Vincitore, 1982 Mercian Colorado, 1976 Puch Royal X, 1973 Raleigh Competition, 1971 Gitane Tour de France and others
Mentioned: 55 Post(s)
Tagged: 0 Thread(s)
Quoted: 823 Post(s)
Liked 1,396 Times
in
694 Posts
+1 on the mild ovalizing of chainring bolt holes to make a 130 fit a 128 bcd Nervar Star. For a while I ran my Allegro using a 47T Sugino ring I modified that way, and it was discrete and drew no attention.
Likes For rustystrings61:
#18
Senior Member
Join Date: Apr 2006
Location: Washington County, Vermont, USA
Posts: 3,778
Bikes: 1966 Dawes Double Blue, 1976 Raleigh Gran Sport, 1975 Raleigh Sprite 27, 1980 Univega Viva Sport, 1971 Gitane Tour de France, 1984 Lotus Classique, 1976 Motobecane Grand Record
Mentioned: 77 Post(s)
Tagged: 0 Thread(s)
Quoted: 765 Post(s)
Liked 660 Times
in
351 Posts
Stronglight 93 et al. at 122mm should be able to take a 36t with a little trimming of the spider arm tabs. I plan to make one, have the holes marked out, needs drilling counterboring and trimming, just haven't got a round tooit.
CAD drawing is from here.
Mark B
CAD drawing is from here.
Mark B
__________________
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
Likes For jonwvara:
#19
Senior Member
Join Date: Apr 2006
Location: Washington County, Vermont, USA
Posts: 3,778
Bikes: 1966 Dawes Double Blue, 1976 Raleigh Gran Sport, 1975 Raleigh Sprite 27, 1980 Univega Viva Sport, 1971 Gitane Tour de France, 1984 Lotus Classique, 1976 Motobecane Grand Record
Mentioned: 77 Post(s)
Tagged: 0 Thread(s)
Quoted: 765 Post(s)
Liked 660 Times
in
351 Posts
Edit: Just read Bulgie's post #13 and unreservedly accept his word that a 36 o r 37 probably wouldn't work with 128 BCD.He is a real machinist, and I'm a guy who just works with machinists sometimes.
__________________
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
Last edited by jonwvara; 09-15-23 at 05:12 AM.
Likes For jonwvara:
#20
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
Stronglight 93 et al. at 122mm should be able to take a 36t with a little trimming of the spider arm tabs. I plan to make one, have the holes marked out, needs drilling counterboring and trimming, just haven't got a round tooit.
CAD drawing is from here.
Mark B
CAD drawing is from here.
Mark B
I might be able to import a 144 bcd ring drawing to detail out some milling for lightness and style as done using a ring I have as the design reference.
‘still need to have someone mill it out though.
#21
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,999
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 2,580 Times
in
1,080 Posts
I'm not saying send it to the guys I know, but maybe you know someone with a little CNC that you can trade favors with.
#22
blahblahblah chrome moly
Join Date: Apr 2009
Location: Seattle
Posts: 1,999
Mentioned: 92 Post(s)
Tagged: 0 Thread(s)
Quoted: 1182 Post(s)
Liked 2,580 Times
in
1,080 Posts
#23
Senior Member
Join Date: Apr 2006
Location: Washington County, Vermont, USA
Posts: 3,778
Bikes: 1966 Dawes Double Blue, 1976 Raleigh Gran Sport, 1975 Raleigh Sprite 27, 1980 Univega Viva Sport, 1971 Gitane Tour de France, 1984 Lotus Classique, 1976 Motobecane Grand Record
Mentioned: 77 Post(s)
Tagged: 0 Thread(s)
Quoted: 765 Post(s)
Liked 660 Times
in
351 Posts
Yeah, well, 85% of being a machinist is having the necessary machine tools....
__________________
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
www.redclovercomponents.com
"Progress might have been all right once, but it has gone on too long."
--Ogden Nash
Likes For jonwvara:
#24
Senior Member
Join Date: Jun 2006
Posts: 20,305
Mentioned: 130 Post(s)
Tagged: 0 Thread(s)
Quoted: 3464 Post(s)
Liked 2,831 Times
in
1,997 Posts
I know a couple guys with little hobby-sized benchtop CNC mills, that can handle parts this size in aluminum. They're slow but you don't have to stand there watching, you can go for a ride while it chugs away.
I'm not saying send it to the guys I know, but maybe you know someone with a little CNC that you can trade favors with.
I'm not saying send it to the guys I know, but maybe you know someone with a little CNC that you can trade favors with.
I can probably find someone, looking at the original and all the chatter in the slots, need to design a wee bit of tooling to hold the chainring effectively.