Steerer Tube: Replacement on 40's Ballooner fork
#1
Newbie
Thread Starter
Steerer Tube: Replacement on 40's Ballooner fork
This must have been discussed here, but I haven't found it. Show me the way. Thanks, Steve
#3
I'm good to go!
Join Date: Jul 2017
Location: Mississippi
Posts: 14,992
Bikes: Tarmac Disc Comp Di2 - 2020
Mentioned: 51 Post(s)
Tagged: 0 Thread(s)
Quoted: 6196 Post(s)
Liked 4,811 Times
in
3,319 Posts
I can't tell you about replacing it entirely. That might be more for a question in theFramebuilderssub-forum. I don't think many do that as a normal thing.
But since you are likely talking about a steel steerer tube, then cut it off at least a inch or so below where ever a quill stem might get too. And far enough away from the fork crown that the heat of brazing doesn't bother it.
Then braze on another piece of steerer tube of the same ID and OD with a internal union that is at least a half inch into each section of the joined tubes. Then dress up the outside with a file or something to bring the brazed joint back to the OD spec.
But since you are likely talking about a steel steerer tube, then cut it off at least a inch or so below where ever a quill stem might get too. And far enough away from the fork crown that the heat of brazing doesn't bother it.
Then braze on another piece of steerer tube of the same ID and OD with a internal union that is at least a half inch into each section of the joined tubes. Then dress up the outside with a file or something to bring the brazed joint back to the OD spec.
Likes For Iride01:
#4
Senior Member
Join Date: Apr 2016
Posts: 1,236
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 503 Post(s)
Liked 436 Times
in
335 Posts
If you get everything properly clean and close fitting you can use silver solder instead of bronze, significantly lower melting point so no risk of the steerer moving in the crown, and within the ability of a propane torch rather than needing oxy-fuel. I'd go with 7/8" insertion on each side i.e. the width of the inserted tube. Just be sure the solder flows fully, so you can see it all around the other end of the joint.
#5
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,725
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5793 Post(s)
Liked 2,586 Times
in
1,434 Posts
Not sure what the question is, so I'll guess and answer accordingly.
Assuming you're looking for a new fork for an old frame, odds greatly favor it being a standard (USA) 1" steerer. These are very similar, but different to modern 1" steerers, with a slightly smaller ID, different thread pitch, and different headset standards.
You may search for a vintage USA standard 26" middleweight fork, or use a modern fork, but having to replace the stem and headset.
With more info from you, folks will be able to slot in the details.
Assuming you're looking for a new fork for an old frame, odds greatly favor it being a standard (USA) 1" steerer. These are very similar, but different to modern 1" steerers, with a slightly smaller ID, different thread pitch, and different headset standards.
You may search for a vintage USA standard 26" middleweight fork, or use a modern fork, but having to replace the stem and headset.
With more info from you, folks will be able to slot in the details.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
#6
Newbie
Thread Starter
You are right, I was not clear enough. I have a "'44 vintage Rollfast ladies ballooner, which has a steerer tube that has been blown out. I wish to keep the original fork and replace preferably, or repair the steerer tube. Despite my shabby articulation, our members understood and I have gotten some wonderful advice about repairing the tube, Thank you all for those responses. So far not much about removal. I imagine removal to be a less complicated process, and structurally more sound, but I'm here because i really don't know diddley.
Steve
,
Steve
,
#7
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,985
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26425 Post(s)
Liked 10,381 Times
in
7,209 Posts
__________________